REAR DOOR (for Double Cab) > REASSEMBLY |
| 1. INSTALL REAR DOOR WEATHERSTRIP LH |
![]() |
Attach the 34 clips to install the weatherstrip.
| 2. INSTALL REAR DOOR CHECK ASSEMBLY LH |
![]() |
Apply MP grease to the sliding areas of the door check.
Install the door check to the door panel with the 2 nuts.
Apply adhesive to the threads of the bolt.
Install the bolt.
| 3. INSTALL REAR NO. 2 DOOR WEATHERSTRIP LH |
![]() |
Attach the 7 clips to install the weatherstrip.
| 4. INSTALL REAR DOOR OUTSIDE HANDLE ASSEMBLY LH |
![]() |
Install the rear door outside handle with the 2 nuts.
Install the 2 hole plugs.
| 5. INSTALL REAR DOOR LOCK OPEN ROD LH |
| 6. INSTALL REAR DOOR LOCK CHILD PROTECTION COVER LH |
| 7. INSTALL REAR DOOR INSIDE LOCKING CABLE ASSEMBLY LH |
![]() |
Install the rear door inside locking cable.
![]() |
Attach the 3 claws.
| 8. INSTALL REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY LH |
![]() |
Install the rear door lock remote control cable.
| 9. INSTALL REAR DOOR LOCK ASSEMBLY LH |
Apply MP grease to the sliding and rotating parts of the front door lock.
Install a new door lock wire harness packing to the door lock.
![]() |
Using a T30 ''TORX'' wrench, install the door lock with the 3 screws.
Connect the connector.
| 10. INSTALL POWER WINDOW REGULATOR MOTOR ASSEMBLY LH |
Apply MP grease to the sliding and rotating areas of the regulator motor.
![]() |
Using a T25 ''TORX'' driver, install the motor with the 3 screws.
| 11. INSTALL REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY LH |
Apply MP grease to the rear door power window regulator.
![]() |
Loosely install the temporary bolt onto the window regulator.
Insert the window regulator into the door panel. Use the temporary bolt to hang the window regulator on the door panel.
Temporarily install the window regulator with the 3 bolts, and tighten the temporary bolt so that it contacts the door panel.
Tighten the 4 bolts in the order shown in the illustration.
| 12. INSTALL REAR OUTER DOOR GLASS WEATHERSTRIP |
![]() |
Attach the claw to install the weatherstrip.
| 13. INSTALL REAR NO. 2 DOOR GLASS RUN LH |
Install the rear door glass run to the rear door window front lower guide.
| 14. INSTALL REAR DOOR FRONT WINDOW GUIDE SUB-ASSEMBLY LH |
![]() |
Install the rear door front window guide to the door panel with the 2 bolts.
| 15. INSTALL REAR DOOR GLASS SUB-ASSEMBLY LH |
![]() |
Slide the rear door glass to install it as shown in the illustration.
| 16. INSTALL REAR NO. 2 DOOR GLASS RUN LH |
Install the rear door glass run to the rear door window rear lower frame.
| 17. INSTALL REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH |
![]() |
Install the rear door rear lower window frame LH to the door panel with the 4 bolts.
| 18. INSTALL REAR DOOR GLASS RUN LH |
![]() |
Install the rear door glass run.
| 19. INSTALL REAR DOOR SERVICE HOLE COVER LH |
![]() |
Attach the 2 clamps to install the rear door service hole cover.
| 20. INSTALL REAR SPEAKER ASSEMBLY |

Temporarily install the speaker by attaching the claws of the speaker to the door panel.
Install the speaker with the 3 screws.
Connect the connector.
| 21. INSTALL REAR NO. 2 DOOR TRIM BRACKET |
![]() |
Install the bracket with the 2 screws.
| 22. INSTALL REAR INNER DOOR GLASS WEATHERSTRIP LH |
| 23. INSTALL REAR DOOR TRIM BOARD SUB-ASSEMBLY LH |
![]() |
Connect the 2 cables to the inside handle.
Attach the inside handle's knob to the door trim board.
![]() |
Attach the 9 clips to install the door trim board.
Install the inside handle and door trim board to the door trim panel with the screw.
Install the door trim board to the door panel with the screw
Attach the clip.
| 24. INSTALL REAR DOOR ARMREST COVER LH |
| 25. INSTALL COURTESY LIGHT ASSEMBLY |
![]() |
Connect the connector.
Attach the claw to install the courtesy light.
| 26. INSTALL REAR DOOR FRAME GARNISH LH |
![]() |
Attach the 4 clips to install the rear door frame garnish.
| 27. INSTALL REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY |
![]() |
Attach the 4 claws to install the control switch.
| 28. INSTALL REAR UPPER DOOR ARMREST BASE PANEL LH |
![]() |
Connect the connector.
Attach the 2 clips to install the rear upper door armrest base panel.
| 29. INSTALL REAR DOOR INSIDE HANDLE BEZEL PLUG LH |
![]() |
Attach the 4 claws to install the bezel plug.