Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

LIGHTING SYSTEM > Turn Signal Light Circuit

for Preparation Click here


DESCRIPTION

The turn signal flasher receives a turn signal switch signal from the headlight dimmer switch, and illuminates the front turn signal light, outer rear view mirror and rear combination light.

WIRING DIAGRAM


E146098E01


INSPECTION PROCEDURE

1.CHECK TURN SIGNAL LIGHT
  1. Check that the turn signal lights blink.
    Result 
    Result
    Proceed to
    All turn signal lights do not blink
    A
    Only front turn signal light does not blink
    B
    Only rear combination light does not blink
    C
    Only door mirror foot light does not blink
    D



B
Go to step 4

C
Go to step 5

D
Go to step 6
A


2.INSPECT FUSE (LH-IG, TURN-HAZ)
  1. Remove the LH-IG fuse from the main body ECU.

  1. Remove the TURN-HAZ fuse from the engine room junction block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    LH-IG fuse
    Always
    Below 1 Ω
    TURN-HAZ fuse



NG
REPLACE FUSE
OK


3.CHECK HARNESS AND CONNECTOR (TURN SIGNAL FLASHER - BATTERY AND BODY GROUND)
E147627E01
  1. Disconnect the J29 relay connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J29-3 (IG) - Body ground
    Ignition switch ON
    11 to 14 V
    Ignition switch OFF
    Below 1 V
    J29-1 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    J29-4 (E) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

4.CHECK HARNESS AND CONNECTOR (FRONT TURN SIGNAL LIGHT - TURN SIGNAL FLASHER AND BODY GROUND)
E146104E01
E146104E02
  1. for LH:

    1. Disconnect the A12 light connector.

    2. Disconnect the J29 relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A12-3 (B) - J29-10 (LTRN)
      Always
      Below 1 Ω
      A12-2 (E) - Body ground
      A12-3 (B) - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the A13 light connector.

    2. Disconnect the J29 relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      A13-3 (B) - J29-17 (RTRN)
      Always
      Below 1 Ω
      A13-2 (E) - Body ground
      A13-3 (B) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.CHECK HARNESS AND CONNECTOR (REAR COMBINATION LIGHT - TURN SIGNAL FLASHER AND BODY GROUND)
E146105E01
E146105E02
  1. for LH:

    1. Disconnect the R5 light connector.

    2. Disconnect the J29 relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      R5-5 (TRN) - J29-2 (LL)
      Always
      Below 1 Ω
      R5-6 (E) - Body ground
      R5-5 (TRN) - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the R4 light connector.

    2. Disconnect the J29 relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      R4-5 (TRN) - J29-8 (LR)
      Always
      Below 1 Ω
      R4-6 (E) - Body ground
      R4-5 (TRN) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (OUTER REAR VIEW MIRROR - TURN SIGNAL FLASHER AND BODY GROUND)
E147742E01
E147742E02
  1. for LH:

    1. Disconnect the N5 light connector.

    2. Disconnect the J29 relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      N5-4 (B) - J29-2 (LL)
      Always
      Below 1 Ω
      N5-3 (E) - Body ground
      N5-4 (B) - Body ground
      Always
      10 kΩ or higher

  1. for RH:

    1. Disconnect the M6 light connector.

    2. Disconnect the J29 relay connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Condition
      Specified Condition
      M6-4 (B) - J29-8 (LR)
      Always
      Below 1 Ω
      M6-3 (E) - Body ground
      M6-4 (B) - Body ground
      Always
      10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)