BACK WINDOW GLASS (for Regular Cab and Double Cab) > INSTALLATION |
| 1. INSTALL NO. 1 BACK WINDOW GLASS SPACER |
![]() |
Install 2 new spacers onto the back window assembly as shown in the illustration.
| 2. INSTALL NO. 2 BACK WINDOW GLASS SPACER |
![]() |
Install 2 new spacers onto the back window assembly as shown in the illustration.
| 3. INSTALL BACK WINDOW ASSEMBLY |
![]() |
Using a brush or sponge, apply Primer M to the exposed part of the vehicle body.
Using a brush or sponge, apply Primer G to the contact surface of the back window.


Apply adhesive to the back window.
Cut off the tip of the cartridge nozzle as shown in the illustration below.
| Temperature | Usage Time Frame |
| 35°C (95°F) | 15 minutes |
| 20°C (68°F) | 1 hour 40 minutes |
| 5°C (41°F) | 8 hours |
Load the sealer gun with the cartridge.
Apply adhesive to the back window as shown in the illustration.


| Area | Specified Condition |
| a | 12.0 mm (0.472 in.) |
| b | 8.0 mm (0.315 in.) |
![]() ![]() |
Using suction cups, position the glass so that the reference marks are aligned. Press it in gently along the rim.
Lightly press the front surface of the back window to ensure that the back window is securely fit to the vehicle body.
Using a scraper, remove any excess or protruding adhesive.
| Temperature | Minimum time prior to driving vehicle |
| 35°C (95°F) | 1 hour 30 minutes |
| 20°C (68°F) | 5 hours |
| 5°C (41°F) | 24 hours |
| 4. CHECK FOR LEAKS AND REPAIR |
Conduct a leak test after the adhesive has completely hardened.
Seal any leaks with auto glass sealer.
| 5. INSTALL UPPER OUTSIDE BACK WINDOW MOULDING (for Slide Type) |
![]() |
Clean the back window surface.
Using a heat light, heat the back window surface.
Remove the double-sided tape from the back window.
Wipe off any tape adhesive residue with cleaner.
If reusing the moulding:
Clean the moulding.
Using a heat light, heat the moulding.
Remove the double-sided tape from the moulding.
Wipe off any tape adhesive residue with cleaner.
Apply new double-sided tape to the moulding, as shown in the illustration.
Install the moulding.
Using a heat light, heat the back window and moulding.
Remove the peeling paper.
Attach the 3 clips to install the moulding.
| 6. INSTALL LOWER OUTSIDE BACK WINDOW MOULDING |
![]() |
Clean the back window surface.
Using a heat light, heat the back window surface.
Remove the double-sided tape from the back window.
Wipe off any tape adhesive residue with cleaner.
If reusing the moulding:
Clean the moulding.
Using a heat light, heat the moulding.
Remove the double-sided tape from the moulding.
Wipe off any tape adhesive residue with cleaner.
Apply new double-sided tape to the moulding, as shown in the illustration.
Install the moulding.
Using a heat light, heat the back window and moulding.
Remove the peeling paper.
Attach the 3 clips to install the moulding.
| 7. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH |
Attach the clip to install the moulding.

| 8. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING RH |
| 9. INSTALL COAT HOOK |
![]() |
Install the coat hook with the screw.
Attach the 2 claws to install the coat hook cap.
| 10. INSTALL ROOM LIGHT ASSEMBLY (w/ Short Type Roof Console Box) |
Connect the connector.
Attach the 4 clips to install the room light.
Attach the 4 claws to install the lens.

| 11. INSTALL ROOF CONSOLE BOX ASSEMBLY (w/ Long Type Roof Console Box) |
Connect the connector.
Install the roof console box with the 6 screws.
Attach the 4 claws to install the lens.

| 12. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH |
for Regular Cab:
Install the quarter trim panel .
for Double Cab:
Install the quarter trim panel .
| 13. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH |
| 14. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY LH |
for Regular Cab:
Install the quarter trim panel .
for Double Cab:
Install the quarter trim panel .
| 15. INSTALL LOWER QUARTER TRIM PANEL ASSEMBLY RH |
| 16. INSTALL LUGGAGE COMPARTMENT BOX RH (for Regular Cab) |
![]() |
Install the luggage compartment box with the 4 clips.
| 17. INSTALL LUGGAGE COMPARTMENT BOX LH (for Regular Cab) |
![]() |
Attach the 3 claws to install the luggage compartment box.
Install the 2 clips.
| 18. INSTALL UPPER BACK PANEL GARNISH (for Regular Cab) |
![]() |
Attach the 10 clips to install the back panel garnish.
| 19. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH (for Regular Cab) |
| 20. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH (for Regular Cab) |
| 21. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP LH (for Double Cab) |
| 22. INSTALL REAR DOOR OPENING TRIM WEATHERSTRIP RH (for Double Cab) |
| 23. INSTALL FRONT DOOR SCUFF PLATE LH (for Regular Cab) |
![]() |
Attach the 6 claws and 3 clips to install the scuff plate.
| 24. INSTALL FRONT DOOR SCUFF PLATE RH (for Regular Cab) |
| 25. INSTALL REAR DOOR SCUFF PLATE LH (for Double Cab) |
![]() |
Attach the 6 claws and 2 clips to install the scuff plate.
| 26. INSTALL REAR DOOR SCUFF PLATE RH (for Double Cab) |
| 27. INSTALL REAR SEAT ASSEMBLY (for Double Cab) |
Install the rear seat (Click here).
| 28. INSTALL FRONT SEAT ASSEMBLY (for Center Seat) |
Install the front seat (Click here).
| 29. INSTALL FRONT SEAT ASSEMBLY (for Power Seat) |
Install the front seat (Click here).
| 30. INSTALL FRONT SEAT ASSEMBLY (for Manual Seat) |
Install the front seat (Click here).