TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM > TERMINALS OF ECU |
| CHECK 4WD CONTROL ECU |

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| A25-1 (HL1) - A26-4 (GND) | BE - W-B | High-low transfer shift actuator limit switch | Ignition switch ON 4WD control switch 4H | Below 1.5 V |
| Ignition switch ON 4WD control switch 4L | 10.5 to 14 V | |||
| A25-2 (HL2) - A26-4 (GND) | R - W-B | High-low transfer shift actuator limit switch | Ignition switch ON 4WD control switch 4H | 10.5 to 14 V |
| Ignition switch ON 4WD control switch 4L | Below 1.5 V | |||
| A25-3 (HL3) - A26-4 (GND) | GR - W-B | High-low transfer shift actuator limit switch | Ignition switch ON 4WD control switch 4H | 10.5 to 14 V |
| Ignition switch ON 1.5 seconds or less after 4WD HIGH to 4WD LOW switching operation | Below 1.5 V | |||
| Ignition switch ON Over 1.5 seconds after 4WD HIGH to 4WD LOW switching operation | 10.5 to 14 V | |||
| A25-5 (TT) - A25-25 (TGND) | L - P | Temperature sensor | Ignition switch ON | 0 to 5 V |
| A25-6 (TL1) - A26-4 (GND) | V - W-B | 2WD-4WD transfer shift actuator limit switch | Ignition switch ON 4WD control switch 2WD | Below 1.5 V |
| Ignition switch ON 4WD control switch 4H or 4L | 10.5 to 14 V | |||
| A25-8 (TL3) - A26-4 (GND) | W - W-B | 2WD-4WD transfer shift actuator limit switch | Ignition switch ON 4WD control switch 2WD or 4H | 10.5 to 14 V |
| Ignition switch ON 4WD control switch 4L | Below 1.5 V | |||
| A25-9 (DL1) - A26-4 (GND) | LG - W-B | A.D.D. actuator limit switch | Ignition switch ON 4WD control switch 2WD (A.D.D. actuator Free) | 10.5 to 14 V |
| Ignition switch ON 4WD control switch 4H (A.D.D. actuator Lock) | Below 1.5 V | |||
| A25-10 (DL2) - A26-4 (GND) | R - W-B | A.D.D. actuator limit switch | Ignition switch ON 4WD control switch 2WD (A.D.D. actuator Free) | Below 1.5 V |
| Ignition switch ON 4WD control switch 4H (A.D.D. actuator Lock) | 10.5 to 14 V | |||
| A25-11 (2-4) - A26-4 (GND) | B - W-B | 4WD control switch | Ignition switch ON 4WD control switch 2WD or 4H | Below 1.5 V |
| Ignition switch ON 4WD control switch 4L | 10.5 to 14 V | |||
| A25-13 (LO) - A26-4 (GND) | P - W-B | 4WD control switch | Ignition switch ON 4WD control switch 2WD | 10.5 to 14 V |
| Ignition switch ON 4WD control switch 4H or 4L | Below 1.5 V | |||
| A25-14 (4WD) - A26-4 (GND) | SB - W-B | 2WD-4WD transfer shift actuator 4WD detection switch | Ignition switch ON 4WD control switch 2WD | 9.5 to 14 V |
| Ignition switch ON 4WD control switch 4H | Below 1.5 V | |||
| A25-15 (ADD) - A26-4 (GND) | W - W-B | A.D.D. actuator A.D.D. detection switch | Ignition switch ON 4WD control switch 2WD | 10 to 14 V |
| Ignition switch ON 4WD control switch 4H | Below 1.5 V | |||
| A25-16 (NP) - A26-4 (GND) | B - W-B | 2WD-4WD transfer shift actuator neutral detection switch | Ignition switch ON 1.5 seconds or less after 4WD HIGH to 4WD LOW switching operation | Below 1.5 V |
| Ignition switch ON Over 1.5 seconds after 4WD HIGH to 4WD LOW switching operation | 10 to 14 V | |||
| A25-19 (CANH) - A25-20 (CANL) | BE - W | CAN communication line | Ignition switch OFF | 54 to 69 Ω |
| A25-21 (L4) - A26-4 (GND) | Y - W-B | Transfer 4LO signal | Except 4WD control switch 4L | 10 to 14 V |
| Ignition switch ON 4WD control switch 4L | Below 1.5 V | |||
| A26-1 (DM1) - A26-4 (GND) | W - W-B | A. D. D. actuator motor | Ignition switch ON 4WD control switch 4H (During operation of A.D.D. actuator from Lock to Free) | 10 to 14 V |
| Ignition switch ON 4WD control switch 4H (A.D.D. actuator Free) | Below 1.5 V | |||
| A26-2 (HM1) - A26-4 (GND) | GR - W-B | High-low transfer shift actuator motor | Ignition switch ON 4WD control switch 4L → 4H (During operation of high-low transfer shift actuator motor from 4WD LOW to 4WD HIGH) | 10 to 14 V |
| Ignition switch ON 4WD control switch 4L → 4H (High-low transfer shift actuator motor stopped) | Below 1.5 V | |||
| A26-3 (IG) - A26-4 (GND) | V - W-B | IG power | Ignition switch ON | 11 to 14 V |
| A26-4 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| A26-5 (DM2) - A26-4 (GND) | Y - W-B | A. D. D. actuator motor | Ignition switch ON 4WD control switch 4H (during operation of A.D.D. actuator from Free to Lock) | 10 to 14 V |
| Ignition switch ON 4WD control switch 4H (A.D.D. actuator Lock) | Below 1.5 V | |||
| A26-6 (HM2) - A26-4 (GND) | P - W-B | High-low transfer shift actuator motor | Ignition switch ON 4WD control switch 4H → 4L (During operation of high-low transfer shift actuator motor from 4WD HIGH to 4WD LOW) | 10 to 14 V |
| Ignition switch ON 4WD control switch 4H → 4L (High-low transfer shift actuator motor stopped) | Below 1.5 V | |||
| A26-7 (TM2) - A26-4 (GND) | LG - W-B | 2WD-4WD transfer shift actuator motor | Ignition switch ON 4WD control switch 4H → 2WD (During operation of 2WD-4WD transfer shift actuator motor from 4WD HIGH to 2WD) | 10 to 14 V |
| Ignition switch ON 4WD control switch 4H → 2WD (2WD-4WD transfer shift actuator motor stopped) | Below 1.5 V | |||
| A26-8 (TM1) - A26-4 (GND) | R - W-B | 2WD-4WD transfer shift actuator motor | Ignition switch ON 4WD control switch 2WD → 4H (During operation of 2WD-4WD transfer shift actuator motor from 2WD to 4WD HIGH) | 10 to 14 V |
| Ignition switch ON 4WD control switch 2WD → 4H (2WD-4WD transfer shift actuator motor stopped) | Below 1.5 V |