Home › DRIVE LINE › JF1A TRANSFER › TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM

TOUCH SELECT 2-4 AND HIGH-LOW SYSTEM > SYSTEM DESCRIPTION

for Preparation Click here



DRIVING MODE SWITCHING PATTERN

C160086E01


2WD TO 4WD HIGH SWITCHING CONTROL (Pattern A)


1.CHANGE 4WD CONTROL SWITCH FROM 2WD TO 4H

    NEXT


    2.2WD-4WD TRANSFER SHIFT ACTUATOR MOTOR IS OPERATED


      C160101E01

    1. Vehicle speed judgment.

      HINT:
      When the vehicle speed is 100 km/h (62 mph) or more, vehicle speed limit violation control is performed.

    2. 2WD to 4WD HIGH switching vehicle speed limit violation control
      Control
      1. Motor operation prohibited
      2. 4HI indicator light blinks at 0.5 second intervals
      3. Warning buzzer sounds at 0.5 second intervals
      Release of Control
      4WD control switch: 2WD


    NEXT


    3.4WD DETECTION SWITCH IS TURNED ON
      Result 
      Condition
      Proceed to
      After 4WD control switch operation, detection switch turns ON within 10 seconds
      A
      After 4WD control switch operation, detection switch does not turn ON even after 10 seconds have passed
      B


    B.
    Go to step 7
    A


    4.A.D.D. ACTUATOR MOTOR IS OPERATED

      HINT:
      When switching the A.D.D. actuator motor, the rotation difference limit violation control operates when either of the following occurs: 1) there is a difference in the rotation of the front wheels and rear wheels; or 2) there is a difference in the rotation of the front left wheel and front right wheel.
      1. Rotation difference limit violation control
      Control
      1. A.D.D. actuator motor operation prohibited
      2. Warning buzzer sounds once (0.5 seconds on, 0.5 seconds off)
      Release of Control
      1. Difference in rotation of front wheels and rear wheels: Less than 21.15 km/h (13.1 mph)
      2. Difference in rotation of front left wheel and front right wheel: Less than 5.5 km/h (3.4 mph)


    NEXT


    5.A.D.D. ACTUATOR IS LOCKED (A.D.D. DETECTION SWITCH IS TURNED ON)

      HINT:
      If the A.D.D. actuator motor is performing the switch from 2WD to 4WD and then the 4WD control switch is returned to 2WD, the 2WD switching operation is started after the 2WD to 4WD switch completion.


    NEXT


    6.4HI INDICATOR LIGHT COMES ON
    1. The 4HI indicator light comes on when the 2WD to 4WD HIGH switch is complete.

    2. HINT:
      If the 4WD control switch is changed to 4L before the 4WD HIGH switch completion, switch prohibition control is performed.
      1. Switch prohibition control
        Control
        1. 4LO indicator light blinks at 0.5 second intervals
        2. Warning buzzer sounds at 0.5 second intervals
        Release of Control
        4WD control switch: Changed to position other than 4L


    NEXT

    END


    7.4WD HIGH TO 2WD RETURN CONTROL IS PERFORMED
    1. 4WD HIGH to 2WD return control
      Control
      1. 4HI indicator light blinks at 0.5 second intervals
      2. Switches to 2WD
      Release of Control
      When 2WD switch completed

      NOTICE:
      1. When the return control is completed, the 4WD control switch is in the 4H position but the vehicle is in the 2WD state, and this inconsistency causes the 4HI indicator light to blink at 0.2 second intervals. Changing the 4WD control switch to the 2WD position stops the blinking.
      2. When the 4HI indicator light blinks at 0.2 second intervals, the system is malfunctioning. Refer to the PROBLEM SYMPTOMS TABLE (Click here).


    NEXT

    END


    4WD HIGH TO 2WD SWITCHING CONTROL (Pattern B)


    1.CHANGE 4WD CONTROL SWITCH FROM 4H TO 2WD

      NEXT


      2.2WD-4WD TRANSFER SHIFT ACTUATOR MOTOR IS OPERATED
      1. Control is possible when driving at less than 100 km/h (62 mph).

        HINT:
        When the vehicle speed is 100 km/h (62 mph) or more, vehicle speed limit violation control is performed.
        1. 4WD HIGH to 2WD switching vehicle speed limit violation control
          Control
          1. Motor operation prohibited
          2. 4HI indicator light blinks at 0.5 second intervals
          3. Warning buzzer sounds at 0.5 second intervals
          Release of Control
          4WD control switch: 4H


      NEXT


      3.4WD DETECTION SWITCH IS TURNED OFF

        NEXT


        4.A.D.D. ACTUATOR BECOMES FREE (A.D.D. DETECTION SWITCH IS TURNED OFF)

          HINT:
          If the A.D.D. actuator motor is performing the switch from 4WD to 2WD and then the 4WD control switch is returned to 4H, the 4WD switching operation is started after the 4WD to 2WD switch completion.


        NEXT


        5.4HI INDICATOR LIGHT TURNS OFF
        1. The 4HI indicator light turns off when the 4WD HIGH to 2WD switch is complete.

          HINT:
          If the 4WD control switch is changed to 4L before the 2WD switch completion, switch prohibition control is performed.
          1. Switch prohibition control
            Control
            1. 4LO indicator light blinks at 0.5 second intervals
            2. Warning buzzer sounds at 0.5 second intervals
            Release of Control
            4WD control switch: Changed to position other than 4L


        NEXT

        END


        4WD HIGH TO 4WD LOW SWITCHING CONTROL (Pattern C)


        1.CHANGE 4WD CONTROL SWITCH FROM 4H TO 4L

          NEXT


          2.HIGH-LOW TRANSFER SHIFT ACTUATOR MOTOR IS OPERATED
          1. The high-low transfer shift actuator motor operates when all of the following conditions are met: 1) the vehicle speed is less than 5 km/h (3 mph); 2) the shift lever is on N.

            HINT:
            When the conditions are not met, the 4WD HIGH to 4WD LOW switching violation control operates.
            1. 4WD HIGH to 4WD LOW switching violation control (if violation occurs after high-low transfer shift actuator motor operation has started)
              Control
              1. 4LO indicator light blinks at 0.5 second intervals
              2. Warning buzzer sounds at 0.5 second intervals
              3. Actuator fork is in neutral position (driving is impossible)
              Release of Control
              Vehicle speed is less than 5 km/h (3 mph) and shift lever is on N (after release of control, warning buzzer stops and 4LO indicator light blinks at 0.5 second intervals until 4WD LOW switch completion)
            2. 4WD HIGH to 4WD LOW switching violation control (if violation occurs before high-low transfer shift actuator motor operation has started)
              Control
              1. 4LO indicator light blinks at 0.5 second intervals
              2. Warning buzzer sounds at 0.5 second intervals
              3. Motor operation prohibited
              Release of Control
              Vehicle speed is less than 5 km/h (3 mph) and shift lever is on N (after release of control, warning buzzer stops and 4LO indicator light blinks at 0.5 second intervals until 4WD LOW switch completion)
              4WD control switch is changed to 4H or 2WD (switching operation occurs depending on switch position)


          NEXT


          3.ACTUATOR LOW IS DETECTED
            Result 
            Condition
            Proceed to
            After 4WD control switch operation, ACTUATOR LOW detection occurs within 3 seconds
            A
            After 4WD control switch operation, ACTUATOR LOW detection does not occur even after 3 seconds have passed
            B

            HINT:
            After 4WD control switch operation, if ACTUATOR LOW is not detected even after 3 seconds have passed, the 4WD HIGH to 4WD LOW return control is performed.



          B.
          Go to step 5
          A


          4.4LO INDICATOR LIGHT TURNS ON
          1. The 4LO indicator light turns on when the 4WD HIGH to 4WD LOW switch is complete.


          NEXT

          END


          5.4WD LOW TO 4WD HIGH RETURN CONTROL IS PERFORMED
          1. 4WD LOW to 4WD HIGH return control
            Control
            1. 4LO indicator light blinks at 0.5 second intervals
            2. 4WD LOW side operation is stopped, and operation is switched to 4WD HIGH side
            Release of Control
            When 4WD HIGH switch completed

            NOTICE:
            1. When the return control is completed, the 4WD control switch is in the 4L position but the vehicle is in the 4WD HIGH state, and this inconsistency causes the 4LO indicator light to blink at 0.2 second intervals. Changing the 4WD control switch to the 4H position stops the blinking. (The 4HI indicator light remains illuminated.)
            2. When the 4LO indicator light blinks at 0.2 second intervals, the system is malfunctioning. Refer to the PROBLEM SYMPTOMS TABLE (Click here).

            HINT:
            The 4WD LOW to 4WD HIGH switching violation control operates when all of the following conditions are met during 4WD LOW to 4WD HIGH return control: 1) the vehicle speed is less than 5 km/h (3 mph); 2) the shift lever is on N.


          NEXT

          END


          4WD LOW TO 4WD HIGH SWITCHING CONTROL (Pattern D)


          1.CHANGE 4WD CONTROL SWITCH FROM 4L TO 4H

            NEXT


            2.HIGH-LOW TRANSFER SHIFT ACTUATOR MOTOR IS OPERATED
            1. The high-low transfer shift actuator motor operates when all of the following conditions are met: 1) the vehicle speed is less than 5 km/h (3 mph); 2) the shift lever is on N.

              HINT:
              When the conditions are not met, the 4WD LOW to 4WD HIGH switching violation control operates.
              1. 4WD LOW to 4WD HIGH switching violation control (if violation occurs after high-low transfer shift actuator motor operation has started)
                Control
                1. 4LO indicator light blinks at 0.5 second intervals
                2. Warning buzzer sounds at 0.5 second intervals
                3. Actuator fork is in neutral position (driving is impossible)
                Release of Control
                Vehicle speed is less than 5 km/h (3 mph) and shift lever is on N (after release of control, warning buzzer stops and 4LO indicator light blinks at 0.5 second intervals until 4WD HIGH switch completion)
              2. 4WD LOW to 4WD HIGH switching violation control (if violation occurs before high-low transfer shift actuator motor operation has started)
                Control
                1. 4LO indicator light blinks at 0.5 second intervals
                2. Warning buzzer sounds at 0.5 second intervals
                3. Motor operation prohibited
                Release of Control
                Vehicle speed is less than 5 km/h (3 mph) and shift lever is on N (after release of control, warning buzzer stops and 4LO indicator light blinks at 0.5 second intervals until 4WD HIGH switch completion)
                4WD control switch is changed to 4L (switching operation occurs depending on switch position)


            NEXT


            3.ACTUATOR HIGH IS DETECTED
              Result 
              Condition
              Proceed to
              After 4WD control switch operation, ACTUATOR HIGH detection occurs within 3 seconds
              A
              After 4WD control switch operation, ACTUATOR HIGH detection does not occur even after 3 seconds have passed
              B

              HINT:
              After 4WD control switch operation, if ACTUATOR HIGH is not detected even after 3 seconds have passed, the 4WD LOW to 4WD HIGH return control is performed.



            B.
            Go to step 5
            A


            4.4HI INDICATOR LIGHT ILLUMINATES
            1. The 4HI indicator light illuminates when the 4WD LOW to 4WD HIGH switch is complete.


            NEXT

            END


            5.4WD HIGH TO 4WD LOW RETURN CONTROL IS PERFORMED
            1. 4WD HIGH to 4WD LOW return control
              Control
              1. 4LO indicator light blinks at 0.5 second intervals
              2. 4WD HIGH side operation is stopped, and operation is switched to 4WD LOW side
              Release of Control
              1. When 4WD LOW switch completed

              NOTICE:
              1. When the return control is completed, the 4WD control switch is in the 4H position but the vehicle is in the 4WD LOW state, and this inconsistency causes the 4LO indicator light to blink at 0.2 second intervals. Changing the 4WD control switch to the 4L position stops the blinking of the 4LO indicator light and causes it to illuminate.
              2. When the 4LO indicator light blinks at 0.2 second intervals, the system is malfunctioning. Refer to the PROBLEM SYMPTOMS TABLE (Click here).

              HINT:
              The 4WD HIGH to 4WD LOW switching violation control operates when all of the following conditions are met during 4WD HIGH to 4WD LOW return control: 1) the vehicle speed is less than 5 km/h (3 mph); 2) the shift lever is on N.


            NEXT

            END


            4WD LOW TO 2WD SWITCHING CONTROL (Pattern E)

            HINT:
            The switching operation occurs in the following order: 1) 4WD LOW to 4WD HIGH switching control; 2) 4WD HIGH to 2WD switching control.


            INDICATOR LIGHT
            1. 4HI Indicator Light

              Indicator Condition
              Vehicle Condition
              Details [Terminal Name: Switch Condition]
              Illuminates
              4WD HIGH
              1. 2WD-4WD transfer shift actuator limit switch 4WD [TL1: OFF, TL3: ON]
              2. 2WD-4WD transfer shift actuator 4WD detection switch 4WD [4WD: ON]
              3. High-low transfer shift actuator limit switch High [HL1: ON, HL2: OFF, HL3: OFF]
              4. High-low transfer shift actuator neutral position switch 4HI [NP: OFF]
              5. A.D.D. actuator limit switch Lock [DL1: ON, DL2: OFF]
              6. A.D.D. actuator A.D.D. detection switch Lock [ADD: ON]
              During 4WD HIGH to 2WD switching
              While 2WD-4WD transfer shift actuator and A.D.D. actuator are switching, within 3 seconds of operation of 4WD control switch (4H to 2WD)
              Does not illuminate
              2WD
              1. 2WD-4WD transfer shift actuator limit switch 2WD [TL1: ON, TL3: OFF]
              2. 2WD-4WD transfer shift actuator 4WD detection switch 2WD [4WD: OFF]
              3. High-low transfer shift actuator limit switch High [HL1: ON, HL2: OFF, HL3: OFF]
              4. High-low transfer shift actuator neutral position switch 4HI [NP: OFF]
              5. A.D.D. actuator limit switch Free [DL1: OFF, DL2: ON]
              6. A.D.D. actuator A.D.D. detection switch Free [ADD: OFF]
              During 2WD to 4WD HIGH switching
              While 2WD-4WD transfer shift actuator and A.D.D. actuator are switching, within 3 seconds of operation of 4WD control switch (2WD to 4H)
              4WD LOW
              1. 2WD-4WD transfer shift actuator limit switch 4WD [TL1: OFF, TL3: ON]
              2. 2WD-4WD transfer shift actuator 4WD detection switch 4WD [4WD: ON]
              3. High-low transfer shift actuator limit switch Low [HL1: OFF, HL2: ON, HL3: OFF]
              4. High-low transfer shift actuator neutral position switch 4LO [NP: OFF]
              5. A.D.D. actuator limit switch Lock [DL1: ON, DL2: OFF]
              6. A.D.D. actuator A.D.D. detection switch Lock [ADD: ON]
              During 4WD LOW to 4WD HIGH or 4WD LOW to 2WD switching
              1. From change of 4WD control switch from 4L to 4H, until high-low transfer shift actuator change completes
              2. From change of 4WD control switch from 4L to 2WD, until high-low transfer shift actuator change completes
              Blinks (ON: 0.5 seconds, OFF: 0.5 seconds)
              During 2WD to 4WD HIGH or 4WD HIGH to 2WD switching
              While 2WD-4WD transfer shift actuator and A.D.D. actuator are switching, from 3 seconds or more after operation of 4WD control switch (2WD to 4H or 4H to 2WD) to switch completion
              During 4WD LOW to 2WD return control
              During 4WD LOW to 2WD switching
              After change of 4WD control switch from 4L to 2WD, from high-low transfer shift actuator switch completion until 2WD-4WD transfer shift actuator and A.D.D. actuator switch completion
              When ignition switch is ON and 4WD control switch is between 2WD and 4H, or 4H and 4L
              Blinks (ON: 0.5 seconds, OFF: 0.5 seconds)
              Warning buzzer sounds (ON: 0.5 seconds OFF: 0.5 seconds)
              During 2WD to 4WD HIGH or 4WD HIGH to 2WD switching control violation
              1. At ambient temperature and vehicle speed at 100 km/h (62 mph) or more, 2WD to 4WD switching operation is performed
              2. With vehicle speed at 100 km/h (62 mph) or more, 4WD to 2WD switching operation is performed
              During A.D.D. actuator switching violation
              During A.D.D. actuator switching, there is difference in rotation of front wheels and rear wheels or front left and right wheel
              Blinks (ON: 0.2 seconds, OFF: 0.2 seconds)
              During malfunction
              1. During A.D.D. actuator limit switch malfunction
              2. During 2WD-4WD transfer shift actuator limit switch malfunction
              3. During 2WD to 4WD switching control malfunction
              4. During wheel speed signal malfunction
              5. During vehicle speed signal malfunction
              From 2WD to 4WD return control switching completion until 4WD control switch is changed to 2WD

            2. 4LO Indicator Light

              Indicator Condition
              Vehicle Condition
              Details [Terminal Name: Switch Condition]
              Illuminates
              4WD LOW
              1. 2WD-4WD transfer shift actuator limit switch 4WD [TL1: OFF, TL3: ON]
              2. 2WD-4WD transfer shift actuator 4WD detection switch 4WD [4WD: ON]
              3. High-low transfer shift actuator limit switch Low [HL1: OFF, HL2: ON, HL3: OFF]
              4. High-low transfer shift actuator neutral position switch 4LO [NP: OFF]
              5. A.D.D. actuator limit switch Lock [DL1: ON, DL2: OFF]
              6. A.D.D. actuator A.D.D. detection switch Lock [ADD: ON]
              During 4WD LOW to 4WD HIGH switching
              While High-Low transfer shift actuator is switching, within 3 seconds of operation of 4WD control switch (4L to 4H)
              Does not illuminate
              2WD
              1. 2WD-4WD transfer shift actuator limit switch 2WD [TL1: ON, TL3: OFF]
              2. 2WD-4WD transfer shift actuator 4WD detection switch 2WD [4WD: OFF]
              3. High-low transfer shift actuator limit switch High [HL1: ON, HL2: OFF, HL3: OFF]
              4. High-low transfer shift actuator neutral position switch 4HI [NP: OFF]
              5. A.D.D. actuator limit switch Free [DL1: OFF, DL2: ON]
              6. A.D.D. actuator A.D.D. detection switch Free [ADD: OFF]
              During 2WD to 4WD HIGH switching
              4WD HIGH
              1. 2WD-4WD transfer shift actuator limit switch 4WD [TL1: OFF, TL3: ON]
              2. 2WD-4WD transfer shift actuator 4WD detection switch 4WD [4WD: ON]
              3. High-low transfer shift actuator limit switch High [HL1: ON, HL2: OFF, HL3: OFF]
              4. High-low transfer shift actuator neutral position switch 4HI [NP: OFF]
              5. A.D.D. actuator limit switch Lock [DL1: ON, DL2: OFF]
              6. A.D.D. actuator A.D.D. detection switch Lock [ADD: ON]
              During 4WD HIGH to 2WD switching
              During 4WD HIGH to 4WD LOW switching
              While high-low transfer shift actuator is switching, within 3 seconds of operation of 4WD control switch (4H to 4L)
              Blinks (ON: 0.5 seconds, OFF: 0.5 seconds)
              During 4WD LOW to 4WD HIGH, or 4WD HIGH to 4WD LOW switching
              While High-Low transfer shift actuator is switching, from 3 seconds or more after operation of 4WD control switch (4L to 4H or 4H to 4L) to switch completion
              1. During 4WD LOW to 4WD HIGH return control
              2. During 4WD HIGH to 4WD LOW return control
              When ignition switch is ON and 4WD control switch is between 2WD and 4H, or 4H and 4L
              Blinks (ON: 0.5 seconds, OFF: 0.5 seconds)
              Warning buzzer sounds (ON: 0.5 seconds OFF: 0.5 seconds)
              During 4WD LOW to 4WD HIGH or 4WD LOW to 2WD switching control violation
              1. With vehicle speed at 5 km/h (3 mph) or more, 4WD HIGH to 4WD LOW or 4WD LOW to 4WD HIGH switching operation is performed
              2. With shift lever on position other than N, 4WD HIGH to 4WD LOW or 4WD LOW to 4WD HIGH switching operation is performed
              When 2WD to 4WD HIGH switching is not completed, from when 4WD control switch is accidentally changed to 4L, until 4WD control switch is changed to 4H or 2WD
              Blinks (ON: 0.2 seconds, OFF: 0.2 seconds)
              During malfunction
              1. During High-low transfer shift actuator limit switch malfunction
              2. During 4WD HIGH to 4WD LOW switching control malfunction
              3. During vehicle speed signal malfunction
              4. During shift position P signal malfunction
              5. During shift position N signal malfunction
              6. During engine speed signal malfunction
              1. From 4WD HIGH to 4WD LOW return control completion, until 4WD control switch is changed to 4H or 2WD
              2. From 3 seconds after 4WD HIGH to 4WD LOW return control start (shift fork of high-low transfer shift actuator is in neutral position), until 4WD control switch is changed to 4H or 2WD
              3. From 4WD LOW to 4WD HIGH return control completion, until 4WD control switch is changed to 4L
              4. From 3 seconds after 4WD LOW to 4WD HIGH return control start (shift fork of high-low transfer shift actuator is in neutral position), until 4WD control switch is changed to 4L


            C160142E02