Home › DRIVE LINE › JF1A TRANSFER › TRANSFER CASE REAR OIL SEAL

TRANSFER CASE REAR OIL SEAL > REPLACEMENT

for Preparation Click here



1. DRAIN TRANSFER OIL


    C159809
  1. Remove the 4 bolts and lower transfer case protector.

  1. Remove the filler plug and gasket.

  1. Remove the drain plug and gasket, and drain the transfer oil.



2. REMOVE PROPELLER SHAFT ASSEMBLY (for 2 Joint Type)


C158453E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 nuts and 4 bolts, and disconnect the propeller shaft from differential side.



    C158455E01
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts and propeller shaft.



3. REMOVE PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 3 Joint Type)


C158453E01
  1. Place matchmarks on the propeller shaft flange and differential flange.

  1. Remove the 4 bolts and 4 nuts.



    C158454
  1. w/o Bearing Washer:

    1. Remove the 2 mounting bolts from the frame crossmember.

  1. w/ Bearing Washer:

    1. Remove the 2 mounting bolts and 2 bearing washers from the frame crossmember.



    C158455E01
  1. Place matchmarks on the propeller shaft flange and transfer flange.

  1. Remove the 4 nuts and propeller shaft.



4. REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    C159617
  1. Using a chisel and hammer, loosen the staked part of the lock nut.



    C159618E01
  1. Using SST to hold the companion flange, remove the lock nut.

    SST
    09330-00021  



    C159619E01
  1. Using SST, remove the companion flange.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)



5. REMOVE TRANSFER CASE REAR OIL SEAL


    C159302E01
  1. Using SST, tap out the oil seal.

    SST
    09308-00010  

    NOTICE:
    Do not damage the oil-seal-fitted surface of the rear extension housing.



6. INSTALL TRANSFER CASE REAR OIL SEAL
  1. Apply transfer oil to the spline area of the output shaft.



    C159303E01
  1. Using SST and a hammer, tap in the oil seal until its surface is flush with the housing upper surface.

    SST
    09316-60011   (09316-00011)



7. INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Install the companion flange onto the output shaft.



    C159618E01
  1. Using SST to hold the companion flange, install a new companion flange lock nut.

    SST
    09330-00021  

    Torque:
    127 N*m{ 1299 kgf*cm , 94 ft.*lbf }



    F050151E01
  1. Using a chisel and hammer, stake the companion flange lock nut.



8. INSTALL PROPELLER SHAFT ASSEMBLY (for 2 Joint Type)


HINT:
When replacing the spider bearing, make sure that the grease fitting assembly hole is facing in the direction shown in the illustration.



C158514E01



    C158453E01
  1. Align the matchmarks on the propeller shaft flange and differential flange.

  1. Install the propeller shaft to the differential side with the 4 bolts and 4 nuts.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }



    C158455E01
  1. Align the matchmarks on the propeller shaft flange and transfer flange.

  1. Install the propeller shaft to the transfer side with the 4 nuts.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }



9. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 3 Joint Type)


HINT:
When replacing the spider bearing, make sure that the grease fitting assembly hole is facing in the direction shown in the illustration.



C160963E01



    C158454
  1. w/o Bearing Washer:

    1. Temporarily install the center support bearing to the crossmember with the 2 mounting bolts.



    C179315E01
  1. w/ Bearing Washer:

    1. Temporarily install the center support bearing to the crossmember with the 2 bearing washers and 2 mounting bolts.



    C158455E01
  1. Align the matchmarks on the flange yoke and transfer flange.

  1. Install the propeller shaft to the transfer side with the 4 nuts.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }



    C158453E01
  1. Align the matchmarks on the flange yoke and differential flange.

  1. Install the propeller shaft to the differential side with the 4 bolts and 4 nuts.

    Torque:
    70 N*m{ 714 kgf*cm , 52 ft.*lbf }



10. ADD TRANSFER OIL
  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. Pour oil so that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the filler plug hole.

    NOTICE:
    1. Pour oil slowly.
    2. Pour oil a little at a time, waiting several minutes between each addition of oil.

  1. Wait approximately 5 minutes and check that the oil level has not changed.

  1. Install a new gasket and the filler plug.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



    C159809
  1. Install the lower transfer case protector with the 4 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }



11. CHECK TRANSFER OIL
  1. Remove the filler plug and gasket.



    C083746E08
  1. Check that the oil level is between 0 to 5.0 mm (0 to 0.197 in.) from the bottom lip of the filler plug hole.
    If the result is not as specified, add transfer oil.

    Oil grade:
    GL-4 or GL-5

    Viscosity:
    SAE 75W-90

    Standard capacity:
    1.1 +/- 0.06 liters (1.2 +/- 0.06 US qts, 1.0 +/- 0.05 Imp. qts)

    NOTICE:
    1. After changing the oil, drive the vehicle and check the oil level again.
    2. Too much or too little oil will lead to transfer problems.

  1. When the oil level is too low, check for oil leak.

  1. Install a new gasket into the filler plug and then tighten the plug.



12. CHECK FOR TRANSFER OIL LEAK