ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE OIL FILTER ELEMENT |
![]() |
Connect a hose with an inside diameter of 15 mm (0.591 in.) to the pipe.
![]() |
Remove the oil filter drain plug.
![]() |
Install the pipe to the oil filter cap.
![]() |
Check that oil is drained from the oil filter. Then disconnect the pipe and remove the O-ring, as shown in the illustration.
![]() |
Using SST, remove the oil filter cap.
![]() |
Remove the oil filter element and O-ring from the oil filter cap.
| 2. REMOVE NO. 1 OIL COOLER BRACKET (w/ Oil Cooler) |
![]() |
Remove the 2 nuts and bracket.
Disconnect the ground wire from the cylinder block.
| 3. REMOVE OIL FILTER BRACKET (w/ Oil Cooler) |
![]() |
Remove the 2 bolts, 2 nuts and filter bracket.
![]() |
Remove the 2 O-rings.
| 4. REMOVE OIL FILTER BRACKET (w/o Oil Cooler) |
![]() |
Remove the 2 bolts, 2 nuts and oil filter bracket.
![]() |
Remove the 2 O-rings.
| 5. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, loosen the crankshaft pulley set bolt.
Partially install the pulley set bolt to the crankshaft until 2 or 3 threads are engaged.
![]() |
Using the pulley set bolt and SST, remove the crankshaft pulley.
| 6. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
| 7. REMOVE OIL FILLER CAP HOUSING |
![]() |
Remove the 2 bolts, filler cap housing and gasket.
| 8. REMOVE SPARK PLUG |
| 9. REMOVE VVT SENSOR |
![]() |
LH:
Remove the 2 bolts and 2 VVT sensors.
![]() |
RH:
Remove the 2 bolts and 2 VVT sensors.
| 10. REMOVE CAMSHAFT POSITION SENSOR |
![]() |
Remove the bolt and camshaft position sensor.
| 11. REMOVE CRANK POSITION SENSOR PROTECTOR |
![]() |
Remove the 2 bolts and sensor protector.
| 12. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Remove the bolt and crankshaft position sensor.
| 13. REMOVE CAMSHAFT OIL CONTROL VALVE ASSEMBLY |
![]() |
LH:
Remove the 2 bolts and 2 oil control valves.
![]() |
RH:
Remove the 2 bolts and 2 oil control valves.
| 14. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY LH |
![]() |
Remove the 14 bolts, seal washer, cylinder head cover and gasket.
![]() |
Remove the 5 gaskets from the camshaft bearing caps (No. 2, No. 3).
| 15. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY RH |
![]() |
Remove the bolt and noise filter.
![]() |
Remove the 14 bolts, seal washer, cylinder head cover and gasket.
![]() |
Remove the 5 gaskets from the camshaft bearing caps (No. 1, No. 3).
| 16. REMOVE OIL CONTROL VALVE FILTER |
![]() |
LH:
Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.
![]() |
RH:
Remove the 3 bolts, cylinder head cover spacer, gasket and valve filter.
| 17. REMOVE SPARK PLUG TUBE GASKET |
![]() |
Bend the 4 ventilation baffle plate claws on the cylinder head cover to an angle of 90° or more.
Using a screwdriver, pry out the gaskets.
| 18. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the 8 bolts, water pump and gasket.
| 19. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Remove the 28 bolts and nut shown in the illustration.
![]() |
Remove the timing chain cover by prying between it and the cylinder head and cylinder block with a screwdriver as shown in the illustration.
![]() |
Remove the oil pump gasket from the cylinder block.
![]() |
Remove the O-ring from the oil pan.
| 20. REMOVE WATER INLET PIPE |
![]() |
Remove the water inlet pipe.
Remove the 2 O-rings from the water inlet pipe.
| 21. REMOVE FRONT CRANKSHAFT OIL SEAL |
Place the timing chain cover on wooden blocks.
![]() |
Place the oil pump on a wooden block.
Using a screwdriver and wooden block, pry out the oil seal.
| 22. SET NO. 1 CYLINDER TO TDC / COMPRESSION |
Temporarily tighten the pulley set bolt.
Rotate the crankshaft clockwise so that the timing marks on the crankshaft timing gear and camshaft timing gears are as shown in the illustration.

| 23. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY LH |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.
![]() |
Remove the 2 bolts, chain tensioner and gasket.
| 24. REMOVE NO. 1 CHAIN TENSIONER SLIPPER LH |
![]() |
| 25. REMOVE NO. 1 CHAIN VIBRATION DAMPER LH |
![]() |
Remove the 2 bolts and chain vibration damper.
| 26. REMOVE NO. 1 CHAIN SUB-ASSEMBLY LH |
![]() |
While pushing down the No. 3 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket LH.
Remove the No. 1 and No. 2 chains from the gears.
| 27. REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the 2 bolts and chain tensioner.
| 28. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY RH |
![]() |
Move the stopper plate upward to release the lock, and push the plunger deep into the tensioner.
Move the stopper plate downward to set the lock, and insert a hexagon wrench into the stopper plate hole.
![]() |
Remove the 2 bolts and chain tensioner.
| 29. REMOVE NO. 1 CHAIN TENSIONER SLIPPER RH |
![]() |
| 30. REMOVE NO. 1 CHAIN VIBRATION DAMPER RH |
![]() |
Remove the 2 bolts and vibration damper.
| 31. REMOVE NO. 1 CHAIN SUB-ASSEMBLY RH |
![]() |
While raising up the No. 2 chain tensioner, insert a pin of φ1.0 mm (0.0394 in.) into the hole to fix it in place.
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
![]() |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.
Remove the No. 1 and No. 2 chains from the gears.
| 32. REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the 2 bolts and chain tensioner.
| 33. REMOVE CRANKSHAFT TIMING GEAR KEY |
![]() |
Using a screwdriver, remove the 2 timing gear keys from the crankshaft.
| 34. REMOVE CAMSHAFT BEARING CAP LH |
![]() |
Make sure that the knock pin of the camshaft is positioned as shown in the illustration.
![]() |
Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.
Remove the 6 bearing caps.
Remove the No. 3 and No. 4 camshafts.
| 35. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH |
![]() |
Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.
| 36. REMOVE CAMSHAFT BEARING CAP RH |
![]() |
Make sure that the knock pin of the camshaft is positioned as shown in the illustration.
![]() |
Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
![]() |
Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.
Remove the 6 bearing caps.
Remove the No. 1 and No. 2 camshafts.
| 37. REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH |
![]() |
Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.
| 38. REMOVE VALVE ROCKER ARM SUB-ASSEMBLY |
Remove the 32 valve rocker arms from the cylinder head.
| 39. REMOVE VALVE LASH ADJUSTER ASSEMBLY |
Remove the 32 valve lash adjusters from the cylinder head.
| 40. REMOVE VALVE STEM CAP |
Remove the 32 valve stem caps from the cylinder head.
| 41. REMOVE CYLINDER HEAD SUB-ASSEMBLY LH |
![]() |
Uniformly loosen and remove the 2 bolts in the sequence shown in the illustration.
![]() |
Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.
| 42. REMOVE CYLINDER HEAD SUB-ASSEMBLY RH |
![]() |
Uniformly loosen and remove the 2 bolts in the sequence shown in the illustration.
![]() |
Using a 10 mm bi-hexagon wrench, uniformly loosen the 10 cylinder head bolts in the sequence shown in the illustration. Remove the 10 cylinder head bolts and plate washers.
| 43. REMOVE CYLINDER HEAD GASKET LH |
| 44. REMOVE CYLINDER HEAD GASKET RH |
| 45. REMOVE CYLINDER BLOCK WATER JACKET SPACER |
![]() |
Remove the 2 water jacket spacers from the cylinder head.
| 46. REMOVE OIL RETURN PIPE GASKET |
![]() |
Using a screwdriver, pry out the oil return pipe gasket.
| 47. REMOVE VENTILATION PIPE GASKET |
![]() |
Using a screwdriver, pry out the ventilation pipe gasket.
| 48. REMOVE NO. 1 HEAT EXCHANGER COVER |
![]() |
Remove the 12 bolts and 2 nuts.
![]() |
Remove the heat exchanger by prying between the heat exchanger and cylinder block with a screwdriver.
| 49. REMOVE NO. 2 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 14 bolts and 2 nuts.
![]() |
Insert the blade of oil pan seal cutter between the oil pans. Cut through the applied sealer and remove the No. 2 oil pan.
| 50. REMOVE NO. 1 OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 14 bolts and 2 nuts.
![]() |
Remove the oil pan by prying between the oil pan and cylinder block with a screwdriver.
| 51. REMOVE NO. 1 OIL PAN BAFFLE PLATE |
![]() |
Remove the 7 bolts and baffle plate.
| 52. REMOVE OIL STRAINER SUB-ASSEMBLY |
![]() |
Remove the 2 bolts, oil strainer and O-ring.
| 53. REMOVE ENGINE REAR OIL SEAL RETAINER |
![]() |
Remove the 6 bolts and oil seal retainer.
![]() |
Using a screwdriver, pry out the oil seal retainer.
| 54. REMOVE OIL DRAIN PIPE SUB-ASSEMBLY |
![]() |
Remove the bolt and oil drain pipe.
Remove the O-ring.
| 55. REMOVE REAR CRANKSHAFT OIL SEAL |
![]() |
Place the oil seal retainer on wooden blocks.
Using a screwdriver and hammer, tap out the oil seal.
| 56. REMOVE RING PIN |
| 57. REMOVE STUD BOLT |