Home › ENGINE ยท 3UR-FE › ENGINE CONTROL SYSTEM › HEATED OXYGEN SENSOR

HEATED OXYGEN SENSOR > INSTALLATION

for Preparation Click here



1. INSTALL HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)


    A158663
  1. Install the sensor to the exhaust pipe by hand.



    A148589E01
  1. Using SST, tighten the sensor.

    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.



2. INSTALL HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)


    A158663
  1. Install the sensor to the exhaust pipe by hand.



    A148589E01
  1. Using SST, tighten the sensor.

    SST
    09224-00010  

    Torque:
    without SST:
    44 N*m{ 449 kgf*cm , 32 ft.*lbf }
    with SST:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). If using a torque wrench with a length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the wrench are connected in a straight line.



3. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. Install a new gasket and the exhaust pipe to the exhaust manifold RH with 3 new nuts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the exhaust pipe to the center exhaust pipe with the 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector and 2 clamps.



4. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY (for Regular Cab Standard Deck)
  1. Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 3 new nuts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the front No. 2 exhaust pipe to the front No. 3 exhaust pipe with the 2 bolts and 2 new nuts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector.



5. INSTALL FRONT NO. 2 EXHAUST PIPE ASSEMBLY (except Regular Cab Standard Deck)
  1. Connect the front No. 2 exhaust pipe to the exhaust pipe support.

  1. Install a new gasket and the front No. 2 exhaust pipe to the exhaust manifold LH with 3 new nuts.

    Torque:
    54 N*m{ 551 kgf*cm , 40 ft.*lbf }

  1. Install a new gasket and the front No. 2 exhaust pipe to the center exhaust pipe with the 2 bolts.

    Torque:
    48 N*m{ 489 kgf*cm , 35 ft.*lbf }

  1. Connect the air fuel ratio sensor connector.

  1. Connect the heated oxygen sensor connector.



6. INSTALL FRONT PROPELLER SHAFT ASSEMBLY (for 4WD)


C158457E01
  1. for Front Differential Side:

    1. Align the matchmarks on the differential and propeller shaft flange.

    2. Install the propeller shaft with the 4 washers and 4 nuts.

      Torque:
      80 N*m{ 816 kgf*cm , 59 ft.*lbf }



    C158456E02
  1. for Transfer Side:

    1. Align the matchmarks on the transfer and propeller shaft flange.

    2. Connect the propeller shaft with the 4 washers and 4 nuts.

      Torque:
      80 N*m{ 816 kgf*cm , 59 ft.*lbf }



7. INSTALL PROPELLER SHAFT HEAT INSULATOR (for 4WD)


C158452
  1. Install the heat insulator to the heat insulator bracket with the 2 bolts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }



8. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.