Home › BODY › SEAT › REAR SEAT ASSEMBLY (for CrewMax RH Side)

REAR SEAT ASSEMBLY (for CrewMax RH Side) > REASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat cushion spring and seatback frame may injure your hands.



1. INSTALL SEAT LOCK CONTROL CABLE SUB-ASSEMBLY RH


B168937
  1. Install the control cable to the seatback frame.

  1. Connect the 2 cables.



2. INSTALL REAR SEAT CUSHION SUPPORT ASSEMBLY


B165065
  1. Install the cushion support with the 6 nuts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



3. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY RH


B165064
  1. Using a T45 "TORX" socket, install the frame with the 5 bolts.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



4. INSTALL RECLINING ADJUSTER INSIDE COVER RH


B165062
  1. Attach the claw to install the cover.

  1. Install the 2 screws.



5. INSTALL RECLINING ADJUSTER INSIDE COVER LH


B165063
  1. Attach the claw to install the cover.

  1. Install the 2 screws.



6. INSTALL REAR SEAT CUSHION MOULDING RH


B165060
  1. Attach the 2 claws to install the moulding.

  1. Install the 3 screws.



7. INSTALL REAR SEAT CUSHION MOULDING LH


B165061
  1. Attach the 2 claws to install the moulding.

  1. Install the 3 screws.



8. INSTALL REAR SEAT CUSHION SPRING ASSEMBLY RH


B165059
  1. Install the 2 bushes to the cushion spring. Then using a T45 "TORX" socket, install the 2 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }

  1. Install the 2 bolts.

    Torque:
    22 N*m{ 224 kgf*cm , 16 ft.*lbf }



9. INSTALL SEPARATE TYPE REAR SEATBACK COVER RH
  1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



10. INSTALL REAR SEATBACK COVER WITH PAD RH


  1. Attach the hooks to install the seatback cover (with pad).


    B165054E02



11. INSTALL LOWER REAR SEATBACK COVER SUB-ASSEMBLY RH


B165048E02
  1. Using hog ring pliers, install the seatback cover with new hog rings.



12. INSTALL REAR SEAT LOCK CONTROL LEVER SUB-ASSEMBLY RH


    B165053E01
  1. Connect the cable in the order shown in the illustration to install the lever.



    B165051
  1. Install the 2 screws.



13. INSTALL REAR SEATBACK LOCK STRIKER COVER RH


B165050
  1. Attach the 2 claws to install the cover.



14. INSTALL REAR SEAT HEADREST SUPPORT


B165049
  1. Attach the 4 claws to install the 2 supports.



15. INSTALL REAR SEAT HEADREST ASSEMBLY RH


16. INSTALL REAR SEATBACK COVER


B170218
  1. Attach the 4 claws to install the cover.



17. INSTALL REAR SEATBACK BOARD RH


B165047
  1. Attach the 2 clips to install the seatback board.

  1. Install the 4 screws.



18. INSTALL REAR SEAT CUSHION MOULDING REAR RH


B165056E01
  1. Attach the 2 claws in the order shown in the illustration to install the moulding.

  1. Install the screw.



19. INSTALL REAR SEAT CUSHION MOULDING REAR LH


B165058E01
  1. Attach the 2 claws in the order shown in the illustration to install the moulding.

  1. Install the screw.



20. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER RH
  1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.



21. INSTALL REAR SEAT CUSHION COVER WITH PAD RH
  1. Attach the hooks to install the seat cushion cover (with pad).



  1. Install the seat belt with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }



    B165046E02



    B165045E02
  1. Using hog ring pliers, install the rubber band of the seatback cover to the seat frame with new hog rings.