Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > TERMINALS OF ECM

for Preparation Click here



CHECK ECM

A107881E92

  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    The standard normal voltage between each pair of ECM terminals is shown in the table below. The appropriate conditions for checking each pair of terminals are also indicated. The result of checks should be compared with the standard normal voltage for that pair of terminals, displayed in the Specified Condition column. The illustration above can be used as a reference to identify the ECM terminal locations.


    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A24-1 (BATT) - D74-81 (E1)
    L - BR
    Battery (for measuring battery voltage and for ECM memory)
    Always
    11 to 14 V
    D74-41 (+BM) - D74-81 (E1)
    P - BR
    Power source of throttle actuator
    Always
    11 to 14 V
    A24-28 (IGSW) - D74-81 (E1)
    LG - BR
    Ignition switch
    Ignition switch ON
    11 to 14 V
    A24-3 (+B) - D74-81 (E1)
    GR - BR
    Power source of ECM
    Ignition switch ON
    11 to 14 V
    A24-2 (+B2) - D74-81 (E1)
    GR - BR
    Power source of ECM
    Ignition switch ON
    11 to 14 V
    D74-58 (OC1+) - D74-57 (OC1-)
    B - B-L
    Camshaft timing oil control valve (OCV) (for Intake Side of Bank 1)
    Idling
    Pulse generation
    (see waveform 1)
    D74-52 (OC2+) - D74-51 (OC2-)
    L-B - R-B
    Camshaft timing oil control valve (OCV) (for Intake Side of Bank 2)
    Idling
    Pulse generation
    (see waveform 1)
    D74-56 (OE1+) - D74-55 (OE1-)
    L-W - L-B
    Camshaft timing oil control valve (OCV) (for Exhaust Side of Bank 1)
    Idling
    Pulse generation
    (see waveform 1)
    D74-50 (OE2+) - D74-49 (OE2-)
    L-R - L
    Camshaft timing oil control valve (OCV) (for Exhaust Side of Bank 2)
    Idling
    Pulse generation
    (see waveform 1)
    A24-34 (MREL) - D74-81 (E1)
    W - BR
    EFI relay
    Ignition switch ON
    11 to 14 V
    D74-74 (VG) - D74-75 (E2G)
    L-Y - G-W
    Mass air flow meter
    Idling, Shift lever position P or N, A/C switch OFF
    0.5 to 3.0 V
    D74-73 (THA) - D74-97 (ETHW)
    Y-B - BR
    Intake air temperature sensor
    Idling, Intake air temperature 20°C (68°F)
    0.5 to 3.4 V
    D74-76 (THW) - D74-98 (ETHA)
    G-B - BR
    Engine coolant temperature sensor
    Idling, Engine coolant temperature 80°C (176°F)
    0.2 to 1.0 V
    D74-80 (VCTA) - D74-79 (ETA)
    Y - L
    Power source of throttle position sensor (specific voltage)
    Ignition switch ON
    4.5 to 5.5 V
    D74-78 (VTA1) - D74-79 (ETA)
    R-Y - L
    Throttle position sensor (for engine control)
    Ignition switch ON,
    Throttle valve fully closed
    0.5 to 1.2 V
    Ignition switch ON,
    Throttle valve fully open
    3.2 to 4.8 V
    D74-77 (VTA2) - D74-79 (ETA)
    Y-B - L
    Throttle position sensor (for sensor malfunction detection)
    Ignition switch ON,
    Throttle valve fully closed
    2.1 to 3.1 V
    Ignition switch ON,
    Throttle valve fully open
    4.5 to 5.5 V
    A24-55 (VPA) - A24-58 (EPA)
    W - BE
    Accelerator pedal position sensor (for engine control)
    Ignition switch ON,
    Accelerator pedal released
    0.5 to 1.1 V
    Ignition switch ON,
    Accelerator pedal fully depressed
    2.6 to 4.5 V
    A24-56 (VPA2) - A24-60 (EPA2)
    LG - BR
    Accelerator pedal position sensor (for sensor malfunctioning detection)
    Ignition switch ON,
    Accelerator pedal released
    1.2 to 2.0 V
    Ignition switch ON,
    Accelerator pedal fully depressed
    3.4 to 4.7 V
    A24-57 (VCPA) - A24-58 (EPA)
    B - BE
    Power source of accelerator pedal position sensor (for VPA)
    Ignition switch ON
    4.5 to 5.5 V
    A24-59 (VCP2) - A24-60 (EPA2)
    V - BR
    Power source of accelerator pedal position sensor (for VPA2)
    Ignition switch ON
    4.5 to 5.5 V
    D74-22 (HA1A) - D74-23 (E04)
    L - W-B
    A/F sensor heater
    Idling
    Below 3.0 V
    Ignition switch ON
    11 to 14 V
    D74-20 (HA2A) - D74-21 (E05)
    G - W-B
    A/F sensor heater
    Idling
    Below 3.0 V
    Ignition switch ON
    11 to 14 V
    D74-126 (A1A+) - D74-81 (E1)
    G -BR
    A/F sensor
    Ignition switch ON
    3.3 V*1
    D74-125 (A1A-) - D74-81 (E1)
    R - BR
    A/F sensor
    Ignition switch ON
    2.9 V*1
    D74-103 (A2A+) - D74-81 (E1)
    P - BR
    A/F sensor
    Ignition switch ON
    3.3 V*1
    D74-102 (A2A-) - D74-81 (E1)
    L - BR
    A/F sensor
    Ignition switch ON
    2.9 V*1
    D74-45 (HT1B) - D74-46 (E03)
    G-B - W-B
    Heated oxygen sensor heater
    Idling
    Below 3.0 V
    Ignition switch ON
    11 to 14 V
    D74-44 (HT2B) - D74-46 (E03)
    B - W-B
    Heated oxygen sensor heater
    Idling
    Below 3.0 V
    Ignition switch ON
    11 to 14 V
    D74-114 (OX1B) - D74-115 (EX1B)
    G - L
    Heated oxygen sensor
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
    Pulse generation
    (see waveform 2)
    D74-112 (OX2B) - D74-113 (EX2B)
    R - W
    Heated oxygen sensor
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
    Pulse generation
    (see waveform 2)
    D74-86 (#10) - D74-43 (E01)
    R-L - W-B
    Injector
    Ignition switch ON
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    D74-109 (#20) - D74-43 (E01)
    L - W-B
    Injector
    Ignition switch ON
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    D74-85 (#30) - D74-43 (E01)
    R - W-B
    Injector
    Ignition switch ON
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    D74-108 (#40) - D74-43 (E01)
    Y - W-B
    Injector
    Ignition switch ON
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    D74-84 (#50) - D74-43 (E01)
    G - W-B
    Injector
    Ignition switch ON
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    D74-107 (#60) - D74-43 (E01)
    R - W-B
    Injector
    Ignition switch ON
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    D74-83 (#70) - D74-43 (E01)
    W - W-B
    Injector
    Ignition switch ON
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    D74-106 (#80) - D74-43 (E01)
    R-B - W-B
    Injector
    Ignition switch ON
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 3)
    D74-94 (KNK1) - D74-93 (EKNK)
    R - G
    Knock sensor
    Engine speed maintained at 4000 rpm after warming up engine
    Pulse generation
    (see waveform 4)
    D74-117 (KNK2) - D74-116 (EKN2)
    W - B
    Knock sensor
    Engine speed maintained at 4000 rpm after warming up engine
    Pulse generation
    (see waveform 4)
    D74-96 (KNK3) - D74-95 (EKN3)
    W - B
    Knock sensor
    Engine speed maintained at 4000 rpm after warming up engine
    Pulse generation
    (see waveform 4)
    D74-119 (KNK4) - D74-118 (EKN4)
    R - G
    Knock sensor
    Engine speed maintained at 4000 rpm after warming up engine
    Pulse generation
    (see waveform 4)
    D74-92 (VV1+) - D74-91 (VV1-)
    R - G
    Variable valve timing (VVT) sensor (for Intake Side of Bank 1)
    Idling
    Pulse generation
    (see waveform 5)
    D74-87 (VV2+) - D74-88 (VV2-)
    R - Y
    Variable valve timing (VVT) sensor (for Intake Side for Bank 2)
    Idling
    Pulse generation
    (see waveform 5)
    D74-69 (EV1+) - D74-68 (EV1-)
    R-L - B
    Variable valve timing (VVT) sensor (for Exhaust Side of Bank 1)
    Idling
    Pulse generation
    (see waveform 16)
    D74-64 (EV2+) - D74-65 (EV2-)
    R-L - B
    Variable valve timing (VVT) sensor (for Exhaust Side of Bank 2)
    Idling
    Pulse generation
    (see waveform 16)
    D74-110 (NE+) - D74-111 (NE-)
    W - Y
    Crankshaft position sensor
    Idling
    Pulse generation
    (see waveform 5)
    D74-40 (IGT1) - D74-81 (E1)
    B-Y - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    D74-33 (IGT2) - D74-81 (E1)
    L-Y - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    D74-37 (IGT3) - D74-81 (E1)
    B - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    D74-34 (IGT4) - D74-81 (E1)
    L-B - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    D74-35 (IGT5) - D74-81 (E1)
    G-R - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    D74-36 (IGT6) - D74-81 (E1)
    G - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    D74-38 (IGT7) - D74-81 (E1)
    G-W - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    D74-39 (IGT8) - D74-81 (E1)
    G-B - BR
    Ignition coil (ignition signal)
    Idling
    Pulse generation
    (see waveform 6)
    D74-104 (IGF1) - D74-81 (E1)
    G-B - BR
    Ignition coil (ignition confirmation signal)
    Ignition switch ON
    4.5 to 5.5 V
    Idling
    Pulse generation
    (see waveform 6)
    D74-105 (IGF2) - D74-81 (E1)
    R - BR
    Ignition coil (ignition confirmation signal)
    Ignition switch ON
    4.5 to 5.5 V
    Idling
    Pulse generation
    (see waveform 6)
    D74-63 (PRG) - D74-81 (E1)
    L-B - BR
    Purge VSV
    Ignition switch ON
    11 to 14 V
    Idling
    Pulse generation
    (see waveform 7)
    A24-13 (SPD) - D74-81 (E1)
    B - BR
    Speed signal from combination meter
    Driving at 20 km/h (12 mph)
    Pulse generation
    (see waveform 8)
    A24-46 (STA) - D74-81 (E1)
    R - BR
    Starter signal
    Cranking
    5.5 V or more
    D74-120 (NSW) - D74-81 (E1)
    L - BR
    Park / neutral position switch
    Ignition switch ON, Shift lever position other than P and N
    11 to 14 V
    Ignition switch ON, Shift lever position in P or N
    Below 3.0 V
    A24-36 (STP) - D74-81 (E1)
    LG - BR
    Stop light switch
    Brake pedal depressed
    7.5 to 14 V
    Brake pedal released
    Below 1.5 V
    A24-35 (ST1-) - D74-81 (E1)
    R - BR
    Stop light switch
    (opposite to STP terminal)
    Ignition switch ON,
    Brake pedal depressed
    Below 1.5 V
    Ignition switch ON,
    Brake pedal released
    7.5 to 14 V
    D74-19 (M+) - D74-82 (ME01)
    R - W-B
    Throttle actuator
    Idling with warm engine
    Pulse generation
    (see waveform 9)
    D74-18 (M-) - D74-82 (ME01)
    G - W-B
    Throttle actuator
    Idling with warm engine
    Pulse generation
    (see waveform 10)
    A24-52 (FPC) - D74-81 (E1)
    BE - BR
    Fuel pump control
    Ignition switch ON
    Below 1.5 V
    A24-24 (W) - D74-81 (E1)
    P - BR
    MIL
    Ignition switch ON
    Below 3.0 V
    Idling
    11 to 14 V
    A24-16 (TC) - D74-81 (E1)
    R - BR
    Terminal TC of DLC3
    Ignition switch ON
    11 to 14 V
    A24-15 (TACH) - D74-81 (E1)
    W - BR
    Engine speed
    Idling
    Pulse generation
    (see waveform 11)
    A24-30 (VPMP) - D74-81 (E1)
    V - BR
    Vent valve (built into canister pump module)
    Ignition switch ON
    11 to 14 V
    A24-49 (MPMP) - D74-81 (E1)
    G - BR
    Leak detection pump (built into canister pump module)
    Leak detection pump OFF
    Below 3.0 V
    Leak detection pump ON
    11 to 14 V
    D74-67 (VCV1) - D74-97 (ETHW)
    L - BR
    Power source for sensor (specific voltage)
    Ignition switch ON
    4.5 to 5.5 V
    D74-66 (VCV2) - D74-97 (ETHW)
    L - BR
    Power source for sensor (specific voltage)
    Ignition switch ON
    4.5 to 5.5 V
    D74-121 (PPMP) - D74-97 (ETHW)
    P - BR
    Canister pressure sensor (built into canister pump module)
    Ignition switch ON
    3.3 to 4.0 V
    D74-32 (ALT) - D74-81 (E1)
    R - BR
    Generator
    Ignition switch ON
    11 to 14 V
    A24-10 (CANH) - D74-81 (E1)
    GR - BR
    CAN communication line
    Ignition switch ON
    Pulse generation
    (see waveform 12)
    A24-11 (CANL) - D74-81 (E1)
    W - BR
    CAN communication line
    Ignition switch ON
    Pulse generation
    (see waveform 13)
    D74-62 (ACIS) - D74-81 (E1)
    L-Y - BR
    VSV for ACIS (Acoustic Control Induction System) operation signal
    Ignition switch ON
    11 to 14 V
    D74-28 (AIRV) - D74-81 (E1)
    BR - BR
    Air switching valve for secondary air injection system
    Ignition switch ON
    11 to 14 V
    D74-54 (AIRP) - D74-81 (E1)
    P - BR
    Air pump control
    Ignition switch ON
    11 to 14 V
    D74-30 (AIDI) - D74-81 (E1)
    G - BR
    Diagnostic information signal for secondary air injection system
    Air injection system operates
    Pulse generation
    (see waveform 15)
    A24-54 (AIP) - D74-98 (ETHA)
    Y - BR
    Secondary air injection system pressure signal
    Ignition switch ON
    3.0 to 3.6 V
    A24-43 (ARV2) - D74-81 (E1)
    V - BR
    Air switching valve for secondary air injection system
    Ignition switch ON
    11 to 14 V
    D74-53 (ARP2) - D74-81 (E1)
    P-L - BR
    Air pump control
    Ignition switch ON
    11 to 14 V
    D74-29 (AID2) - D74-81 (E1)
    G-Y - BR
    Diagnostic information signal for secondary air injection system
    Air injection system operates
    Pulse generation
    (see waveform 15)
    A24-53 (AIP2) - D74-97 (ETHW)
    G - BR
    Secondary air injection system pressure signal
    Ignition switch ON
    3.0 to 3.6 V
    D74-61 (HAI1) - D74-81 (E1)
    B - BR
    Air pump heater for secondary air injection system
    AI heater operating
    11 to 14 V
    D74-90 (G2) - D74- 89 (G2-)
    R - B
    Camshaft position sensor
    Idling
    Pulse generation
    (see waveform 14)
    A24-18 (DI) - D74-81 (E1)
    L - BR
    Fuel pump control
    Ignition switch ON
    0 to 3.0 V
    A24-14 (STSW) - D74-81 (E1)
    BR - BR
    Starter switch
    Shift lever position P or N, Cranking
    6.0 V or more
    A24-41 (ACCR) - D74-81 (E1)
    BR - BR
    ACC relay control signal
    Ignition switch ON → Cranking
    11 to 14 V → Below 1 V
    D74-16 (STAR) - D74-81 (E1)
    L - BR
    Starter relay control
    Ignition switch ON
    Below 1.5 V
    Cranking
    5.5 V or more
    D74-72 (PSP) - D74-81 (E1)
    G - BR
    Power steering oil pressure sensor
    Ignition switch ON
    0.5 to 4.5 V
    A24-4 (ADJ1)*2 - Body ground
    W-B - Body ground
    Vehicle type designation wire harness
    Always
    Below 1 V

    HINT:
    *1: The ECM terminal voltage is constant regardless of the output voltage from the sensor.
    *2: for 2WD only



  2. A093229E02
  3. WAVEFORM 1:
    Camshaft timing oil control valve (OCV) 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    D74-58 (OC1+) - D74-57 (OC1-)
    5 V/DIV., 1 msec./DIV.
    Idling
    D74-52 (OC2+) - D74-51 (OC2-)
    5 V/DIV., 1 msec./DIV.
    Idling
    D74-56 (OE1+) - D74-55 (OE1-)
    5 V/DIV., 1 msec./DIV.
    Idling
    D74-50 (OE2+) - D74-49 (OE2-)
    5 V/DIV., 1 msec./DIV.
    Idling



  4. A088863E05
  5. WAVEFORM 2:
    Heated oxygen sensor 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    D74-114 (OX1B) - D74-115 (EX1B)
    0.2 V/DIV., 200 msec./DIV.
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor
    D74-112 (OX2B) - D74-113 (EX2B)
    0.2 V/DIV., 200 msec./DIV.
    Engine speed maintained at 2500 rpm for 2 minutes after warming up sensor

    HINT:
    In DATA LIST, item O2S B1S2 and O2S B2S2 show the ECM input values from the heated oxygen sensor.



  6. A093279E04
  7. WAVEFORM 3:
    Injector No. 1 (to No. 8) injection signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    D74-86 (#10) - D74-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    D74-109 (#20) - D74-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    D74-85 (#30) - D74-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    D74-108 (#40) - D74-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    D74-84 (#50) - D74-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    D74-107 (#60) - D74-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    D74-83 (#70) - D74-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling
    D74-106 (#80) - D74-43 (E01)
    20 V/DIV., 20 msec./DIV.
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.



  8. A085286E03
  9. WAVEFORM 4:
    Knock sensor 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    D74-94 (KNK1) - D74-93 (EKNK)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine
    D74-117 (KNK2) - D74-116 (EKN2)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine
    D74-96 (KNK3) - D74-95 (EKN3)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine
    D74-119 (KNK4) - D74-118 (EKN4)
    1 V/DIV., 1 msec./DIV.
    Engine speed maintained at 4000 rpm after warming up engine

    HINT:
    1. The wavelength becomes shorter as the engine rpm increases.
    2. The waveforms and amplitudes displayed differ slightly depending on the vehicle.



  10. A217926E01
  11. WAVEFORM 5:
    Crankshaft position sensor and VVT sensor for intake side 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    (a) D74-110 (NE+) - D74-111 (NE-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (b) D74-92 (VV1+) - D74-91 (VV1-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (c) D74-87 (VV2+) - D74-88 (VV2-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up

    HINT:
    The wavelength becomes shorter as engine rpm increases.



  12. A093278E14
  13. WAVEFORM 6:
    Igniter IGT signal (from ECM to igniter) and Igniter IGF signal (from igniter to ECM) 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    (a) D74-40 (IGT1) - D74-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) D74-33 (IGT2) - D74-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) D74-37 (IGT3) - D74-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) D74-34 (IGT4) - D74-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) D74-35 (IGT5) - D74-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) D74-36 (IGT6) - D74-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) D74-38 (IGT7) - D74-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (a) D74-39 (IGT8) - D74-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (b) D74-104 (IGF1) - D74-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling
    (b) D74-105 (IGF2) - D74-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Idling

    HINT:
    The wavelength becomes shorter as engine rpm increases.



  14. A218020E03
  15. WAVEFORM 7:
    Purge VSV 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    D74-63 (PRG) - D74-81 (E1)
    10 V/DIV., 10 to 100 msec./DIV.
    Idling

    HINT:
    If the waveform is not similar to the illustration, check the waveform again after idling for 10 minutes or more.



  16. A093224E01
  17. WAVEFORM 8:
    Vehicle speed signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    A24-13 (SPD) - D74-81 (E1)
    2 V/DIV., 20 msec./DIV.
    Driving at 20 km/h (12 mph)

    HINT:
    The wavelength becomes shorter as the vehicle speed increases.



  18. A208000E06
  19. WAVEFORM 9:
    Throttle actuator positive terminal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    D74-19 (M+) - D74-82 (ME01)
    5 V/DIV., 1 msec./DIV.
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.



  20. A245848E04
  21. WAVEFORM 10:
    Throttle actuator negative terminal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    D74-18 (M-) - D74-82 (ME01)
    5 V/DIV., 1 msec./DIV.
    Idling with warm engine

    HINT:
    The duty ratio varies depending on the throttle actuator operation.



  22. A164293E01
  23. WAVEFORM 11:
    Engine speed signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    A24-15 (TACH) - D74-81 (E1)
    5 V/DIV., 10 msec./DIV.
    Idling

    HINT:
    The wavelength becomes shorter as the engine rpm increases.



  24. A086154E24
  25. WAVEFORM 12:
    CAN communication signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    A24-10 (CANH) - D74-81 (E1)
    1 V/DIV., 10 μsec./DIV.
    Engine stops and ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  26. A086155E25
  27. WAVEFORM 13:
    CAN communication signal 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    A24-11 (CANL) - D74-81 (E1)
    1 V/DIV., 10 μsec./DIV.
    Engine stops and ignition switch ON

    HINT:
    The waveform varies depending on the CAN communication signal.



  28. A211721E01
  29. WAVEFORM 14:
    Crankshaft position sensor and camshaft position sensor 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    CH1: D74-110 (NE+) - D74-111 (NE-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    CH2: D74-90 (G2) - D74-89 (G2-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up

    HINT:
    The wavelength becomes shorter as the engine rpm increases.



  30. A100214
  31. WAVEFORM 15:
    Terminal DI of air injection control driver 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    D74-30 (AIDI) - D74-81 (E1)
    5 V/DIV., 50 msec./DIV.
    Performing system check using Techstream (secondary air injection check)
    D74-29 (AID2) - D74-81 (E1)
    5 V/DIV., 50 msec./DIV.
    Performing system check using Techstream (secondary air injection check)

    HINT:
    The wavelength changes when the air injection control driver detects malfunctions in the secondary air injection system (Click here).



  32. A217927E01
  33. WAVEFORM 16:
    Crankshaft position sensor and VVT sensor for exhaust side 
    Terminal No. (Symbols)
    Tool Setting
    Condition
    (a) D74-110 (NE+) - D74-111 (NE-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (b) D74-69 (EV1+) - D74-68 (EV1-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up
    (c) D74-64 (EV2+) - D74-65 (EV2-)
    5 V/DIV., 20 msec./DIV.
    Idle after engine warmed up

    HINT:
    The wavelength becomes shorter as engine rpm increases.