Tester Display
| Measurement Item
| Diagnostic Note
|
Vehicle Speed
| Vehicle speed
| Speed indicated on speedometer.
|
Engine Speed
| Engine speed
| -
|
Calculate Load
| Calculated load
| Calculated load by ECM.
|
Vehicle Load
| Vehicle load
| -
|
MAF
| Mass air flow volume
| If approximately 0.0 gm/sec.:
- Mass air flow meter power source circuit open or short.
- VG circuit open or short.
If 160.0 gm/sec. or more:
- E2G circuit open.
|
Atmosphere Pressure
| Atmosphere pressure
| -
|
Coolant Temp
| Engine coolant temperature
| If -40°C (-40°F), sensor circuit open. If 140°C (284°F) or more, sensor circuit shorted.
|
Intake Air
| Intake air temperature
| If -40°C (-40°F), sensor circuit open. If 140°C (284°F) or more, sensor circuit shorted.
|
Engine Run Time
| Accumulated engine running time
| -
|
Initial Engine Coolant Temp
| Engine coolant temperature at engine start
| -
|
Initial Intake Air Temp
| Intake air temperature at engine start
| -
|
Battery Voltage
| Battery voltage
| -
|
Glow Indicator Supported
| Status of glow indicator supported
| -
|
Glow Indicator
| Glow indicator
| -
|
Accel Sens. No. 1 Volt %
| Absolute Accelerator Pedal Position (APP) No. 1
| -
|
Accel Sens. No. 2 Volt %
| Absolute APP No. 2
| -
|
Throttle Sensor Volt %
| Throttle position
| -
|
Throttl Sensor #2 Volt %
| Throttle sensor positioning #2
| -
|
Throttle Sensor Position
| Throttle sensor positioning
| -
|
Throttle Motor DUTY
| Throttle actuator
| -
|
Throttle Position
| Throttle position
| For use when engine stall, starting problems or rough idle is present.
|
ISC Flow
| Flow rate calculated using information from each sensor
| For use when engine stall, starting problems or rough idle is present.
|
ISC Position
| Requested opening amount calculated using ISC control
| For use when engine stall, starting problems or rough idle is present.
|
ISC Feedback Value
| ISC feedback compensation amount
| For use when engine stall, starting problems or rough idle is present.
|
ISC Learning Value
| ISC learned compensation amount
| For use when engine stall, starting problems or rough idle is present.
|
Electric Load Feedback Val
| Compensation flow rate according to electrical load
| For use when engine stall, starting problems or rough idle is present.
|
Air Conditioner FB Val
| Compensation flow rate according to air conditioner load
| For use when engine stall, starting problems or rough idle is present.
|
PS Feedback Val
| Compensation flow rate according to power steering load
| For use when engine stall, starting problems or rough idle is present.
|
Low Revolution Control
| Low engine speed control operation state
| For use when engine stall, starting problems or rough idle is present.
|
N Range Status
| Shift lever N status
| For use when engine stall, starting problems or rough idle is present.
|
Eng Stall Control FB Flow
| Intake air compensation flow rate
| For use when engine stall, starting problems or rough idle is present.
|
Deposit Loss Flow
| Flow loss due to deposits
| For use when engine stall, starting problems or rough idle is present.
|
Fuel Press Switching Valve
| Fuel press switching valve status
| -
|
Injector (Port)
| Injection period of No. 1 cylinder
| -
|
Injection Volum (Cylinder 1)
| Injection volume
| -
|
Fuel Pump/Speed Status
| Fuel pump/speed status
| -
|
Vacuum Pump
| Key-off EVAP system leak detection pump status
| Refer to EVAP System (Click here).
|
EVAP (Purge) VSV
| EVAP purge VSV duty ratio
| -
|
Evap Purge Flow
| Ratio of evaporative purge flow to intake air volume
| -
|
Purge Density Learn Value
| Learning value of purge density
| -
|
EVAP System Vent Valve
| Key-off EVAP system vent valve status
| -
|
EVAP Purge VSV
| EVAP Purge VSV
| -
|
Purge Cut VSV Duty
| Purge cut VSV duty
| -
|
Target Air-Fuel Ratio
| Ratio compared to stoichiometric level
| -
|
AF Lambda B1 S1
| Output air fuel ratio associated with Bank 1 Sensor 1
| -
|
AF Lambda B2 S1
| Output air fuel ratio associated with Bank 2 Sensor 1
| -
|
AFS Voltage B1 S1
| A/F sensor output voltage
| Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
|
AFS Voltage B2 S1
|
AFS Current B1 S1
| A/F sensor current (for Bank 1)
| -
|
AFS Current B2 S1
| A/F sensor current (for Bank 2)
| -
|
A/F Heater Duty #1
| A/F heater duty ratio (for Bank 1)
| -
|
A/F Heater Duty #2
| A/F heater duty ratio (for Bank 2)
| -
|
O2S B1 S2
| Heated oxygen sensor output
| Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables technician to check output voltage of sensor.
|
O2S B2 S2
|
O2S Impedance B1S2
| Sub heated oxygen sensor impedance (for Sensor 2)
| -
|
O2S Impedance B2S2
|
O2 Heater B1S2
| Heated oxygen sensor heater (for Sensor 2)
| -
|
O2 Heater B2S2
|
O2 Heater Curr Val B1S2
| Heated oxygen sensor current (for Sensor 2)
| -
|
O2 Heater Curr Val B2S2
|
Short FT #1
| Short-term fuel trim
| Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
|
Long FT #1
| Long-term fuel trim
| Overall fuel compensation carried out in long term to compensate a continual deviation of short-term fuel trim from central value.
|
A/F Learn Value Idle #1
| Air fuel ratio learned value for idling (for Bank 1)
| -
|
A/F Learn Value Low #1
| Air fuel ratio learned value for low engine loads (for Bank 1)
| -
|
A/F Learn Value Mid1 #1
| Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 1)
| -
|
A/F Learn Value Mid2 #1
| Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 1)
| -
|
A/F Learn Value High #1
| Air fuel ratio learned value for high engine loads (for Bank 1)
| -
|
Total FT #1
| Total fuel trim
| -
|
Short FT #2
| Short-term fuel trim
| Short-term fuel compensation used to maintain air-fuel ratio at stoichiometric air-fuel ratio.
|
Long FT #2
| Long-term fuel trim
| Overall fuel compensation carried out in long term to compensate a continual deviation of short-term fuel trim from central value.
|
A/F Learn Value Idle #2
| Air fuel ratio learned value for idling (for Bank 2)
| -
|
A/F Learn Value Low #2
| Air fuel ratio learned value for low engine loads (for Bank 2)
| -
|
A/F Learn Value Mid1 #2
| Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 2)
| -
|
A/F Learn Value Mid2 #2
| Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 2)
| -
|
A/F Learn Value High #2
| Air fuel ratio learned value for high engine loads (for Bank 2)
| -
|
Total FT #2
| Total fuel trim
| -
|
Fuel System Status #1
| Fuel system status (for Bank 1)
| - OL (Open Loop): Has not yet satisfied conditions to go closed loop.
- CL (Closed Loop): Using A/F sensor as feedback for fuel control.
- OL Drive: Open loop due to driving conditions (fuel enrichment).
- OL Fault: Open loop due to detected system fault.
- CL Fault: Closed loop but A/F sensor, which used for fuel control, malfunctioning.
|
Fuel System Status #2
| Fuel system status (for Bank 2)
| - OL (Open Loop): Has not yet satisfied conditions to go closed loop.
- CL (Closed Loop): Using A/F sensor as feedback for fuel control.
- OL Drive: Open loop due to driving conditions (fuel enrichment).
- OL Fault: Open loop due to detected system fault.
- CL Fault: Closed loop but A/F sensor, which used for fuel control, malfunctioning.
|
Air Pump Pressure (Absolute)
| Air pump pressure (for Bank 1)
| -
|
Air Pump2 Pressure (Absolute)
| Air pump pressure (for Bank 2)
| -
|
Air Pump Pulsation Pressure
| Air pump pulsation pressure (for Bank 1)
| -
|
Air Pump2 Pulsation Pressure
| Air pump pulsation pressure (for Bank 2)
| -
|
Secondary Air Control VSV
| Secondary air injection system status
| -
|
2nd Air System Status
| Secondary air system status
| -
|
AI Test
| Secondary air injection system operation prohibit
| -
|
Subfreezing Conditions
| Subfreezing conditions status
| -
|
Air Pump Freeze
| Air pump freeze status
| -
|
Air Pump2 Freeze
| Air pump 2 freeze status
| -
|
Air Switching Valve Freeze
| Switching valve freeze status
| -
|
Air Switching Valve2 Freeze
| Switching valve 2 freeze status
| -
|
Air Pump Heater
| Air pump heater status
| -
|
IGN Advance
| Ignition advance
| -
|
Knock Feedback Value
| Feedback value of knocking
| -
|
Knock Correct Learn Value
| Correction learning value of knocking
| -
|
Idle Spark Advn Ctrl #1
| Individual cylinder timing advance compensation amount (No. 1)
| For use when engine stall, starting problems or rough idle is present.
|
Idle Spark Advn Ctrl #2
| Individual cylinder timing advance compensation amount (No. 2)
| For use when engine stall, starting problems or rough idle is present.
|
Idle Spark Advn Ctrl #3
| Individual cylinder timing advance compensation amount (No. 3)
| For use when engine stall, starting problems or rough idle is present.
|
Idle Spark Advn Ctrl #4
| Individual cylinder timing advance compensation amount (No. 4)
| For use when engine stall, starting problems or rough idle is present.
|
Idle Spark Advn Ctrl #5
| Individual cylinder timing advance compensation amount (No. 5)
| For use when engine stall, starting problems or rough idle is present.
|
Idle Spark Advn Ctrl #6
| Individual cylinder timing advance compensation amount (No. 6)
| For use when engine stall, starting problems or rough idle is present.
|
Idle Spark Advn Ctrl #7
| Individual cylinder timing advance compensation amount (No. 7)
| For use when engine stall, starting problems or rough idle is present.
|
Idle Spark Advn Ctrl #8
| Individual cylinder timing advance compensation amount (No. 8)
| For use when engine stall, starting problems or rough idle is present.
|
ACIS VSV
| VSV for Acoustic Control Induction System (ACIS)
| -
|
Actual VVT Angle #1
| Actual VVT displacement angle (bank 1)
| This item is used for freeze frame data only
|
Actual VVT Angle #2
| Actual VVT displacement angle (bank 2)
| This item is used for freeze frame data only
|
Actual VVT Ex Angle #1
| Actual VVT exhaust displacement angle (bank 1)
| This item is used for freeze frame data only
|
Actual VVT Ex Angle #2
| Actual VVT exhaust displacement angle (bank 2)
| This item is used for freeze frame data only
|
VVT Control Status #1
| VVT control status (for Bank 1)
| -
|
VVT Control Status #2
| VVT control status (for Bank 2)
| -
|
VVT Advance Fail
| VVT control failure status
| -
|
Catalyst Temp B1 S1
| Estimated catalyst temperature (for Sensor 1)
| -
|
Catalyst Temp B2 S1
|
Catalyst Temp B1 S2
| Estimated catalyst temperature (for Sensor 2)
| -
|
Catalyst Temp B2 S2
|
Starter Signal
| Starter switch (STSW) signal
| -
|
Starter Control
| Starter switch status
| -
|
Power Steering Signal
| Power steering switch status
| -
|
Starter Relay
| Starter relay status
| -
|
ACC Relay
| ACC relay status
| -
|
Neutral Position SW Signal
| Park/Neutral position (PNP) switch signal
| -
|
Transfer L4
| Park/Neutral position (PNP) switch signal
| -
|
Stop Light Switch
| Stop light switch
| -
|
A/C Signal
| A/C signal
| -
|
Closed Throttle Position SW
| Closed throttle position switch
| -
|
Fuel Cut Condition
| Fuel cut condition
| -
|
Immobiliser Communication
| Immobiliser communication
| -
|
TC Terminal
| TC terminal status
| -
|
Time after DTC Cleared
| Cumulative time after DTC cleared
| -
|
Distance from DTC Cleared
| Accumulated distance from DTC cleared
| -
|
Warmup Cycle Cleared DTC
| Warm-up cycle after DTC cleared
| -
|
Dist Batt Cable Disconnect
| Total distance vehicle driven after battery cable disconnected
| -
|
IG OFF Elapsed Time
| Cumulative time after ignition switch off
| -
|
TC and TE1
| TC and CG (TE1) terminals of DLC3
| -
|
Ignition Trig. Count
| Ignition counter
| -
|
Cylinder #1 Misfire Count
| Cylinder #1 misfire count
| -
|
Cylinder #2 Misfire Count
| Cylinder #2 misfire count
| -
|
Cylinder #3 Misfire Count
| Cylinder #3 misfire count
| -
|
Cylinder #4 Misfire Count
| Cylinder #4 misfire count
| -
|
Cylinder #5 Misfire Count
| Cylinder #5 misfire count
| -
|
Cylinder #6 Misfire Count
| Cylinder #6 misfire count
| -
|
Cylinder #7 Misfire Count
| Cylinder #7 misfire count
| -
|
Cylinder #8 Misfire Count
| Cylinder #8 misfire count
| -
|
All Cylinders Misfire Count
| Misfire count of all cylinders
| -
|
Multi Cylinders Misfire Count
| Multiple cylinder misfire count
| -
|
Misfire RPM
| Engine speed when misfire occurred
| -
|
Misfire Load
| Engine load when misfire occurred
| -
|
Misfire Margin
| Margin to detect engine misfire
| -
|
Catalyst OT MF F/C
| Catalyst over temperature misfire prevention F/C
| -
|
Cat OT MF F/C History
| Catalyst over temperature misfire prevention F/C history
| -
|
Cat OT MF F/C Cylinder#1
| Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#2
| Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#3
| Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#4
| Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#5
| Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#6
| Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#7
| Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)
| -
|
Cat OT MF F/C Cylinder#8
| Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)
| -
|
Engine Speed (Starter Off)
| Engine speed when starter off
| For use when engine stall, starting problems or rough idle is present.
|
Starter Count
| Number of times starter turned on after ignition switch turned to ON
| For use when engine stall, starting problems or rough idle is present.
|
Run Dist of Previous Trip
| Distance driven during previous trip
| For use when engine stall, starting problems or rough idle is present.
|
Engine Starting Time
| Time elapsed before engine starts (after starter turns on until engine speed reaches 400 rpm)
| For use when engine stall, starting problems or rough idle is present.
|
Previous Trip Coolant Temp
| Engine coolant temperature during previous trip
| For use when engine stall, starting problems or rough idle is present.
|
Previous Trip Intake Temp
| Intake air temperature during previous trip
| For use when engine stall, starting problems or rough idle is present.
|
Engine Oil Temperature
| Engine oil temperature (estimated temperature)
| For use when engine stall, starting problems or rough idle is present.
|
Previous Trip Eng Oil Temp
| Engine oil temperature during previous trip
| For use when engine stall, starting problems or rough idle is present.
|
Ambient Temp for A/C
| Ambient temperature for A/C
| For use when engine stall, starting problems or rough idle is present.
|
Previous Trip Ambient Temp
| Ambient temperature during previous trip
| For use when engine stall, starting problems or rough idle is present.
|
Engine Start Hesitation
| History of hesitation during engine start
| For use when engine stall, starting problems or rough idle is present.
|
Low Rev for Eng Start
| History of low engine speed after engine start
| For use when engine stall, starting problems or rough idle is present.
|
Minimum Engine Speed
| Minimum engine speed
| For use when engine stall, starting problems or rough idle is present.
|
Power Steering Pressure
| Power steering pressure sensor
| -
|
ACT VSV
| A/C cut status for Active Test
| -
|
Brake Override System
| Brake override system status
| -
|
Idle Fuel Cut
| Fuel cut idle
| ON: when throttle valve fully closed and engine speed over 3500 rpm.
|
FC TAU
| Fuel cut during very light load
| Fuel cut being performed under very light load to prevent engine combustion from becoming incomplete.
|
Immobiliser Fuel Cut
| Status of the immobiliser fuel cut
| -
|
Immobiliser Fuel Cut History
| Immobiliser fuel cut history
| For use when starting problems is present.
|
Alcohol Density Estimate
| Alcohol density estimate
| -
|
Alcohol Density Learning
| Status of the alcohol density learning
| -
|
Fuel Remaining Volume
| Fuel remaining volume
| -
|
Electrical Load Signal 1
| Electrical load signal
| -
|
Electrical Load Signal 2
| Electrical load signal
| -
|
Cruise Cancel Signal
| Status of the cruise cancel signal
| -
|
SPD (NT)
| Input shaft speed
| Data is displayed in increments of 50 rpm.
|
SPD (SP2)
| Output shaft speed
| -
|
Overdrive Cut Switch #1
| Status of the overdrive cut switch
| -
|
Shift SW Status (P Range)
| Park/neutral position switch status (P)
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
Shift SW Status (R Range)
| Park/neutral position switch status (R)
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
Shift SW Status (N Range)
| Park/neutral position switch status (N)
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
Shift SW Status (N,P Range) Supported
| Status of park/neutral position switch (N or P) supported
| -
|
Shift SW Status (N,P Range)
| Park/neutral position switch status (N or P)
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
Sports Shift Up SW
| Sport shift up switch status
| -
|
Sports Shift Down SW
| Sport shift down switch status
| -
|
Sports Mode Selection SW
| Sport mode select switch status
| -
|
Shift SW Status (D Range)
| Park/neutral position switch status (D)
| When the shift lever position displayed on the intelligent tester differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect.
|
A/T Oil Temperature 1
| No. 1 ATF temperature sensor value
| If the value is -40°C or 215°C, the No. 1 ATF temperature sensor circuit open or shorted.
|
A/T Oil Temperature 2
| No. 2 ATF temperature sensor value
| If the value is -40°C or 215°C, the No. 2 ATF temperature sensor circuit open or shorted.
|
Lock Up
| Lock-up
| -
|
Shift Status
| ECM gear shift command
| -
|
SLT Solenoid Status
| Shift solenoid SLT status
| -
|
SLU Solenoid Status
| Shift solenoid SLU status
| -
|
AT Fluid
| Flex lock-up judder judgment
| -
|