SFI SYSTEM > FREEZE FRAME DATA |
| DESCRIPTION |
![]() |
| PENDING FREEZE FRAME DATA |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Select a DTC in order to display its pending freeze frame data.


| LIST OF FREEZE FRAME DATA |
| Tester Display | Measurement Item | Diagnostic Note |
| Vehicle Speed | Vehicle speed | Speed indicated on the speedometer. |
| Engine Speed | Engine speed | - |
| Calculate Load | Calculated load | Load calculated by the ECM. |
| Vehicle Load | Vehicle load | - |
| MAF | Mass airflow volume | If the value is approximately 0.0 gm/sec:
|
| Atmosphere Pressure | Atmospheric pressure | - |
| Coolant Temp | Engine coolant temperature | If the value is -40°C (-40°F), the sensor circuit is open. If the value is 140°C (284°F) or higher, the sensor circuit is shorted. |
| Intake Air | Intake air temperature | If the value is -40°C (-40°F), the sensor circuit is open. If the value is 140°C (284°F) or higher, the sensor circuit is shorted. |
| Engine Run Time | Accumulated engine running time | - |
| Initial Engine Coolant Temp | Engine coolant temperature at engine start | - |
| Initial Intake Air Temp | Intake air temperature at engine start | - |
| Battery Voltage | Battery voltage | - |
| Glow Indicator Supported | Glow indicator supported | - |
| Glow Indicator | Glow indicator | - |
| Accel Sens. No.1 Volt % | Absolute Accelerator Pedal Position (APP) No. 1 | - |
| Accel Sens. No.2 Volt % | Absolute APP No. 2 | - |
| Throttle Sensor Volt % | Throttle sensor position | - |
| Throttl Sensor #2 Volt % | Throttle sensor position #2 | - |
| Throttle Sensor Position | Throttle position | - |
| Throttle Motor DUTY | Throttle actuator | - |
| Throttle Position | Throttle position | For use when engine stall, starting problems or rough idle is present. |
| ISC Flow | Flow rate calculated using information from each sensor | For use when engine stall, starting problems or rough idle is present. |
| ISC Position | Requested opening amount calculated using ISC control | For use when engine stall, starting problems or rough idle is present. |
| ISC Feedback Value | ISC feedback compensation amount | For use when engine stall, starting problems or rough idle is present. |
| ISC Learning Value | ISC learned compensation amount | For use when engine stall, starting problems or rough idle is present. |
| Electric Load Feedback Val | Compensation flow rate according to electrical load | For use when engine stall, starting problems or rough idle is present. |
| Air Conditioner FB Val | Compensation flow rate according to air conditioner load | For use when engine stall, starting problems or rough idle is present. |
| PS Feedback Val | Compensation flow rate according to power steering load | For use when engine stall, starting problems or rough idle is present. |
| Low Revolution Control | Low engine speed control operation state | For use when engine stall, starting problems or rough idle is present. |
| N Range Status | Shift lever N status | For use when engine stall, starting problems or rough idle is present. |
| Eng Stall Control FB Flow | Intake air compensation flow rate | For use when engine stall, starting problems or rough idle is present. |
| Deposit Loss Flow | Flow loss due to deposits | For use when engine stall, starting problems or rough idle is present. |
| Fuel Pump Duty | Fuel pump duty | - |
| Injector (Port) | Injection period of No. 1 cylinder | - |
| Injection Volum (Cylinder 1) | Injection volume | - |
| Vacuum Pump | Key-off EVAP system leak detection pump status | Refer to EVAP System (Click here). |
| Current Fuel Type | Current fuel type | Used to identify the current fuel type: Gasoline |
| EVAP (Purge) VSV | EVAP purge VSV duty ratio | - |
| Evap Purge Flow | Ratio of evaporative purge flow to intake air volume | - |
| Purge Density Learn Value | Purge density learned value | - |
| EVAP System Vent Valve | Key-off EVAP system vent valve status | - |
| EVAP Purge VSV | EVAP purge VSV | - |
| Purge Cut VSV Duty | Purge cut VSV duty | - |
| Target Air-Fuel Ratio | Ratio compared to stoichiometric level | - |
| AF Lambda B1S1 | Fuel trim at air fuel ratio sensor | - |
| AF Lambda B2S1 | Fuel trim at air fuel ratio sensor | - |
| AFS Voltage B1S1 AFS Voltage B2S1 | Air fuel ratio sensor voltage | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor. |
| AFS Current B1S1 | Air fuel ratio sensor current | - |
| AFS Current B2S1 | Air fuel ratio sensor current | - |
| A/F Heater Duty #1 | Air fuel ratio sensor heater duty ratio (for Bank 1) | - |
| A/F Heater Duty #2 | Air fuel ratio sensor heater duty ratio (for Bank 2) | - |
| O2S B1S2 O2S B2S2 | Heated oxygen sensor output | Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check the output voltage of the sensor. |
| O2S Impedance B1S2 O2S Impedance B2S2 | Heated oxygen sensor impedance (for Sensor 2) | - |
| O2 Heater B1S2 O2 Heater B2S2 | Heated oxygen sensor heater (for Sensor 2) | - |
| O2 Heater Curr Val B1S2 O2 Heater Curr Val B2S2 | Heated oxygen sensor current (for Sensor 2) | - |
| Short FT #1 | Short-term fuel trim | Short-term fuel compensation used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio. |
| Long FT #1 | Long-term fuel trim |
|
| A/F Learn Value Idle #1 | Air-fuel ratio learned value for idling (bank 1) | Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher). |
| A/F Learn Value Low #1 | Air-fuel ratio learned value for low engine loads (bank 1) | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid1 #1 | Air-fuel ratio learned value for mid-sized engine loads 1 (bank 1) | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid2 #1 | Air-fuel ratio learned value for mid-sized engine loads 2 (bank 1) | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High #1 | Air-fuel ratio learned value for high engine loads (bank 1) | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
| Total FT #1 | Total fuel trim | - |
| Short FT #2 | Short-term fuel trim | Short-term fuel compensation used to maintain the air-fuel ratio at the stoichiometric air-fuel ratio. |
| Long FT #2 | Long-term fuel trim |
|
| A/F Learn Value Idle #2 | Air-fuel ratio learned value for idling (bank 2) | Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher). |
| A/F Learn Value Low #2 | Air-fuel ratio learned value for low engine loads (bank 2) | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid1 #2 | Air-fuel ratio learned value for mid-sized engine loads 1 (bank 2) | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the low load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value Mid2 #2 | Air-fuel ratio learned value for mid-sized engine loads 2 (bank 2) | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the mid-size load range closer to the high load range (when the range of engine loads is divided into four parts). |
| A/F Learn Value High #2 | Air-fuel ratio learned value for high engine loads (bank 2) | Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts). |
| Total FT #2 | Total fuel trim | - |
| Fuel System Status #1 | Fuel system status (for Bank 1) |
|
| Fuel System Status #2 | Fuel system status (for Bank 2) |
|
| Air Pump Pressure (Absolute) | Air pump pressure (for Bank 1) | - |
| Air Pump2 Pressure (Absolute) | Air pump pressure (for Bank 2) | - |
| Air Pump Pulsation Pressure | Air pump pulsation pressure | - |
| Secondary Air Control VSV | Secondary air control VSV status | - |
| 2nd Air System Status | Secondary air injection system status | - |
| AI Test | Secondary air injection system operation prohibition | - |
| IGN Advance | Ignition advance | - |
| Knock Feedback Value | Knocking feedback value | - |
| Knock Correct Learn Value | Knocking correction learned value | - |
| Idle Spark Advn Ctrl #1 | Individual cylinder timing advance compensation amount (No. 1) | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #2 | Individual cylinder timing advance compensation amount (No. 2) | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #3 | Individual cylinder timing advance compensation amount (No. 3) | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #4 | Individual cylinder timing advance compensation amount (No. 4) | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #5 | Individual cylinder timing advance compensation amount (No. 5) | For use when engine stall, starting problems or rough idle is present. |
| Idle Spark Advn Ctrl #6 | Individual cylinder timing advance compensation amount (No. 6) | For use when engine stall, starting problems or rough idle is present. |
| Actual VVT Angle #1 | Actual VVT angle (for Bank 1) | - |
| Actual VVT Angle #2 | Actual VVT angle (for Bank 2) | - |
| Actual VVT Ex Angle #1 | Actual exhaust VVT angle (for Bank 1) | - |
| Actual VVT Ex Angle #2 | Actual exhaust VVT angle (for Bank 2) | - |
| VVT Control Status #1 | VVT control status (for Bank 1) | - |
| VVT Control Status #2 | VVT control status (for Bank 2) | - |
| VVT Advance Fail | VVT control failure status | - |
| Catalyst Temp B1S1 | Estimated catalyst temperature (for Bank 1 Sensor 1) | - |
| Catalyst Temp B2S1 | Estimated catalyst temperature (for Bank 2 Sensor 1) | - |
| Catalyst Temp B1S2 | Estimated catalyst temperature (for Bank 1 Sensor 2) | - |
| Catalyst Temp B2S2 | Estimated catalyst temperature (for Bank 2 Sensor 2) | - |
| Starter Signal | Starter switch signal | - |
| Starter Control | Starter switch status | - |
| Power Steering Signal | Power steering oil pressure sensor status | - |
| Starter Relay | Starter relay status | - |
| ACC Relay | ACC relay status | - |
| Transfer L4 | Transfer L4 switch status | |
| Neutral Position SW Signal | Park/neutral position (PNP) switch signal | - |
| Stop Light Switch | Stop light switch | - |
| A/C Signal | A/C signal | - |
| Closed Throttle Position SW | Closed throttle position switch | - |
| Fuel Cut Condition | Fuel cut condition | - |
| TC Terminal | TC terminal status | - |
| Time after DTC Cleared | Cumulative time after DTCs cleared | - |
| Distance from DTC Cleared | Accumulated distance driven after DTCs cleared | - |
| Warmup Cycle Cleared DTC | Warmup cycles after DTCs cleared | - |
| Dist Batt Cable Disconnect | Total distance vehicle driven after battery cable disconnected | - |
| IG OFF Elapsed Time | Cumulative time after ignition switch off | - |
| TC and TE1 | TC and CG (TE1) terminals of DLC3 | - |
| Ignition Trig. Count | Ignition counter | - |
| Cylinder #1 Misfire Count | Cylinder #1 misfire count | - |
| Cylinder #2 Misfire Count | Cylinder #2 misfire count | - |
| Cylinder #3 Misfire Count | Cylinder #3 misfire count | - |
| Cylinder #4 Misfire Count | Cylinder #4 misfire count | - |
| Cylinder #5 Misfire Count | Cylinder #5 misfire count | - |
| Cylinder #6 Misfire Count | Cylinder #6 misfire count | - |
| All Cylinders Misfire Count | Misfire count of all cylinders | - |
| Misfire RPM | Engine speed when misfire occurred | - |
| Misfire Load | Engine load when misfire occurred | - |
| Misfire Margin | Margin to detect engine misfire | - |
| Catalyst OT MF F/C | Fuel cut to prevent catalyst from overheating during misfire | - |
| Cat OT MF F/C History | History of fuel cut to prevent catalyst from overheating during misfire | - |
| Cat OT MF F/C Cylinder#1 | Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#2 | Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#3 | Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#4 | Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#5 | Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected) | - |
| Cat OT MF F/C Cylinder#6 | Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected) | - |
| Engine Speed (Starter Off) | Engine speed when starter off | For use when engine stall, starting problems or rough idle is present. |
| Starter Count | Number of times starter turned on after ignition switch turned to ON | For use when engine stall, starting problems or rough idle is present. |
| Run Dist of Previous Trip | Distance driven during previous trip | Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip. After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.
|
| Engine Starting Time | Time elapsed after engine started (interval between ignition switch ON and off) | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Coolant Temp | Engine coolant temperature during previous trip | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Intake Temp | Intake air temperature during previous trip | For use when engine stall, starting problems or rough idle is present. |
| Engine Oil Temperature | Engine oil temperature (estimated temperature) | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Eng Oil Temp | Engine oil temperature during previous trip | For use when engine stall, starting problems or rough idle is present. |
| Ambient Temp for A/C | Ambient temperature for A/C | For use when engine stall, starting problems or rough idle is present. |
| Previous Trip Ambient Temp | Ambient temperature during previous trip | For use when engine stall, starting problems or rough idle is present. |
| Engine Start Hesitation | History of hesitation during engine start | For use when engine stall, starting problems or rough idle is present. |
| Low Rev for Eng Start | History of low engine speed after engine start | For use when engine stall, starting problems or rough idle is present. |
| Minimum Engine Speed | Minimum engine speed | For use when engine stall, starting problems or rough idle is present. |
| Power Steering Pressure | Power steering oil pressure | - |
| ACT VSV | A/C cut status for Active Test | - |
| Brake Override System | Brake Override System | - |
| Idle Fuel Cut | Fuel cut at idle | ON: The throttle valve is fully closed and the engine speed is more than 3500 rpm. |
| FC TAU | Fuel cut during very light load | The fuel cut being performed under a very light load to prevent the engine combustion from becoming incomplete. |
| Electrical Load Signal 1 | Electrical load signal | - |
| Electrical Load Signal 2 | Electrical load signal | - |
| A/F Sensor Determination (worst value) #1 | Worst judgment value of air fuel ratio sensor output (for Bank 1) | - |
| A/F Sensor Determination (worst value) #2 | Worst judgment value of air fuel ratio sensor output (for Bank 2) | - |
| Engine Speed Fluctuation Avg (worst value) #1 | Worst value of average engine speed fluctuation (Cylinder 1) | - |
| Engine Speed Fluctuation Avg (worst value) #2 | Worst value of average engine speed fluctuation (Cylinder 2) | - |
| Engine Speed Fluctuation Avg (worst value) #3 | Worst value of average engine speed fluctuation (Cylinder 3) | - |
| Engine Speed Fluctuation Avg (worst value) #4 | Worst value of average engine speed fluctuation (Cylinder 4) | - |
| Engine Speed Fluctuation Avg (worst value) #5 | Worst value of average engine speed fluctuation (Cylinder 5) | - |
| Engine Speed Fluctuation Avg (worst value) #6 | Worst value of average engine speed fluctuation (Cylinder 6) | - |
| SPD (NT) | Input shaft speed | Data is displayed in increments of 50 rpm. |
| SPD (SP2) | Output shaft speed | - |
| Overdrive Cut Switch #1 | Overdrive cut signal for cruise control | - |
| Shift SW Status (P Range) | PNP switch status (P) | When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Shift SW Status (R Range) | PNP switch status (R) | When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Shift SW Status (N Range) | PNP switch status (N) | When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| Sports Shift Up SW | Sport shift up switch status | - |
| Sports Shift Down SW | Sport shift down switch status | - |
| Sports Mode Selection SW | Sport mode select switch status | - |
| Shift SW Status (D Range) | PNP switch status (D) | When the shift lever position displayed on the Techstream differs from the actual position, the adjustment of the park/neutral position switch assembly or shift cable may be incorrect. |
| A/T Oil Temperature 1 | No. 1 ATF temperature sensor value | If the value is -40°C (-40°F) or 215°C (419°F), the No. 1 ATF temperature sensor circuit is open or shorted. |
| A/T Oil Temperature 2 | No. 2 ATF temperature sensor value | If the value is -40°C (-40°F) or 215°C (419°F), the No. 2 ATF temperature sensor circuit is open or shorted. |
| Lock Up | Lock-up | - |
| Shift Status | ECM gear shift command | - |
| SLT Solenoid Status | Shift solenoid SLT status | - |
| SLU Solenoid Status | Shift solenoid SLU status | - |
| AT Fluid | Flex lock-up judder judgment | - |