Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › INTUITIVE PARKING ASSIST SYSTEM

INTUITIVE PARKING ASSIST SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK CLEARANCE WARNING ECU

C139721E02

  1. Disconnect the J35 ECU connector.

  2. Measure the resistance and voltage according to the value(s) in the table below.

    Terminal No. (Symbols)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    J35-1 (PL) - J35-21 (E)
    P - W-B
    Parking position signal
    Ignition switch ON, shift lever not in P position
    Below 1.5 V
    Ignition switch ON, shift lever in P position
    7 V or higher
    J35-3 (SPD) - J35-21 (E)
    V - W-B
    Vehicle speed signal
    Ignition switch ON, drive wheels are turned slowly
    Alternating between 1.5 to 4.5 V
    J35-6 (SOR) - J35-22 (E2)
    LG - P
    Rear sensor communication signal
    Ignition switch ON, clearance sonar main switch ON
    Waveform 2
    J35-7 (SOF) - J35-23 (E1)
    GR - G
    Front sensor communication signal
    Ignition switch ON, clearance sonar main switch ON
    Waveform 2
    J35-9 (BOF) - J35-21 (E)
    V - W-B
    Ultrasonic sensor power source
    Ignition switch ON, clearance sonar main switch ON
    7.2 to 8.8 V
    J35-10 (IG) - J35-21 (E)
    BE - W-B
    IG signal
    Ignition switch ON, clearance sonar main switch OFF
    Below 1.5 V
    IG power source
    Ignition switch ON, clearance sonar main switch ON
    9 to 15 V
    J35-11 (TL) - J35-21 (E)
    L - W-B
    Illumination light
    Ignition switch ON and light control switch OFF
    Below 1.5 V
    Ignition switch and light control switch ON
    7 V or higher
    J35-12 (BBZ) - J35-21 (E)
    Y - W-B
    Clearance warning buzzer
    Clearance warning buzzer sounding (when the back sonar or clearance sonar senses something)
    Waveform 1
    J35-13 (RL) - J35-21 (E)
    W - W-B
    Reverse position signal
    Ignition switch ON, shift lever not in R position
    Below 1.5 V
    Ignition switch ON, shift lever in R position
    7 V or higher
    J35-15 (L1) - J35-21 (E)
    G - W-B
    Rear corner ultrasonic sensor RH
    Clearance warning indicator LED for rear corner sensor RH illuminates
    Below 3 V
    J35-16 (L2) - J35-21(E)
    V - W-B
    Front corner ultrasonic sensor RH
    Clearance warning indicator LED for front corner sensor RH illuminates
    Below 3 V
    J35-17 (L3) - J35-21 (E)
    GR - W-B
    Rear corner ultrasonic sensor LH
    Clearance warning indicator LED for rear corner sensor LH illuminates
    Below 3 V
    J35-18 (L4) - J35-21 (E)
    LG - W-B
    Front corner ultrasonic sensor LH
    Clearance warning indicator LED for front corner sensor LH illuminates
    Below 3 V
    J35-19 (L5) - J35-21 (E)
    BE - W-B
    Back ultrasonic sensor LH and RH
    Clearance warning indicator LED for back sensor LH and RH illuminates
    Below 3 V
    J35-20 (L6) - J35-21 (E)
    R - W-B
    Clearance warning ECU signal
    Clearance warning indicator's operation indicator illuminates
    Below 3 V
    J35-21 (E) - Body ground
    W-B - Body ground
    ECU ground
    Always
    Below 1 Ω
    J35-22 (E2) - J35-21 (E)
    P - W-B
    ECU ground
    Always
    Below 1 Ω
    J35-23 (E1) - J35-21 (E)
    G - W-B
    ECU ground
    Always
    Below 1 Ω
    J35-24 (BOR) - J35-21 (E)
    Y - W-B
    Ultrasonic sensor power source
    Ignition switch ON, clearance sonar main switch ON
    7.2 to 8.8 V



  3. C139739E03
  4. Using an oscilloscope, check waveform 1.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    J35-12 (BBZ) - J35-21 (E)
    Tool Setting
    2 V/DIV., 200 μsec./DIV.
    Condition
    When sonar detects obstacle (buzzer sounds)



  5. E133127E01
  6. Using an oscilloscope, check waveform 2.
    Measurement Condition 
    Item
    Content
    Terminal No. (Symbol)
    1. CH: 1 J35-7 (SOF) - J35-23 (E1)
    2. CH: 2 J35-6 (SOR) - J35-22 (E2)
    Tool Setting
    2 V/DIV., 200 μsec./DIV.
    Condition
    Ignition switch ON, clearance sonar main switch ON.