Home › BRAKE › BRAKE CONTROL › STEERING ANGLE SENSOR

STEERING ANGLE SENSOR > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.



3. PLACE FRONT WHEELS FACING STRAIGHT AHEAD


4. REMOVE LOWER NO. 3 STEERING WHEEL COVER


    B166432
  1. Using a screwdriver, remove the steering wheel cover.

    HINT:
    Tape the screwdriver tip before use.



5. REMOVE LOWER NO. 2 STEERING WHEEL COVER


    B166433
  1. w/ Cruise Control:

    1. Using a screwdriver, remove the No. 2 steering wheel cover.

      HINT:
      Tape the screwdriver tip before use.



    B167059
  1. w/o Cruise Control:

    1. Using a screwdriver, remove the No. 2 steering wheel cover.

      HINT:
      Tape the screwdriver tip before use.



6. REMOVE STEERING PAD


    B166580E01
  1. Using a T30 "TORX" socket wrench, loosen the 2 screws until the groove along the screw circumference catches on the screw case.



    B166581
  1. Pull out the steering pad from the steering wheel, as shown in the illustration. Then support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the 2 connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.



7. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel set nut.



    C154517E01
  1. Put matchmarks on the steering wheel and main shaft.

  1. Using SST, remove the steering wheel.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05011)



8. REMOVE LOWER STEERING COLUMN COVER


C159214
  1. Remove the 2 screws.

  1. Detach the 2 claws to remove the lower steering column cover.



9. REMOVE UPPER STEERING COLUMN COVER


    C154520
  1. Detach the 4 clips.

  1. Detach the claw to remove the upper steering column cover.



10. REMOVE SPIRAL CABLE SUB-ASSEMBLY


    B166448
  1. Disconnect the connectors from the spiral cable with steering sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Detach the 3 claws and remove the spiral cable with steering sensor.

    NOTICE:
    1. Do not replace the spiral cable sub-assembly when the ignition switch is ON and the battery cable is connected.
    2. Do not rotate the spiral cable when the ignition switch is ON and the battery cable is connected.
    3. Make sure the steering wheel is installed and centered before rotating the steering angle sensor when performing steering angle sensor operation inspections (inspecting for abnormal noise, diagnosis inspections, etc.).
    4. Do not remove the steering angle sensor from the spiral cable.



11. REMOVE STEERING ANGLE SENSOR


    B166448
  1. Disconnect the connectors from the spiral cable with steering sensor.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Detach the 3 claws and remove the spiral cable with steering sensor.

    NOTICE:
    1. Do not replace the spiral cable sub-assembly when the ignition switch is ON and the battery cable is connected.
    2. Do not rotate the spiral cable when the ignition switch is ON and the battery cable is connected.
    3. Make sure the steering wheel is installed and centered before rotating the steering angle sensor when performing steering angle sensor operation inspections (inspecting for abnormal noise, diagnosis inspections, etc.).
    4. Do not remove the steering angle sensor from the spiral cable.