Home › ENGINE · 1UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

SFI SYSTEM > DATA LIST / ACTIVE TEST

for Preparation Click here



DATA LIST

HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Data List.

  7. According to the display on the Techstream, use the Data List.

    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed
    Vehicle speed/
    Min.: 0 km/h, Max.: 255 km/h
    Actual vehicle speed
    Speed indicated on speedometer.
    Engine Speed
    Engine speed/
    Min.: 0 rpm, Max.: 16383 rpm
    650 to 800 rpm: Idling
    -
    Calculate Load
    Calculated load by ECM/
    Min.: 0%, Max.: 100%
    1. 11 to 25%: Idling
    2. 12 to 26%: Driving without load (2500 rpm)
    -
    Vehicle Load
    Vehicle load/
    Min.: 0%, Max.: 25700%
    Actual vehicle load
    -
    MAF
    Air flow rate from Mass Air Flow (MAF) meter/
    Min.: 0 gm/s., Max.: 655.35 gm/s.
    3.4 to 6.2 gm/s.: Idling
    If value approximately 0.0 gm/s.:
    1. Mass air flow meter power source circuit open or shorted.
    2. VG circuit open or shorted.
    If value 160.0 gm/s. or more:
    1. E2G circuit open.
    Atmosphere Pressure
    Atmospheric pressure/
    Min.: 0 kPa, Max.: 255 kPa
    Equivalent to atmospheric pressure (absolute pressure)
    -
    MAP
    Intake manifold pressure/
    Min.: 0 kPa, Max.: 255 kPa
    1. 80 to 110 kPa: Ignition switch ON
    2. 28 to 48 kPa: Idling
    -
    Coolant Temp
    Engine coolant temperature:
    Min.: -40°C, Max.: 215°C
    80 to 100°C (176 to 212°F): After warming up
    If value -40°C (-40°F), sensor circuit open.
    If value 140°C (284°F), sensor circuit shorted.
    Intake Air
    Intake air temperature/
    Min.: -40°C, Max.: 140°C
    Equivalent to ambient air temperature
    If value -40°C (-40°F), sensor circuit open.
    If value 140°C (284°F), sensor circuit shorted.
    Ambient Temperature
    Ambient temperature/
    Min.: -40°C, Max.: 215°C
    Equivalent to ambient air temperature: Ignition switch ON
    -
    Engine Run Time
    Engine run time/
    Min.: 0 s, Max.: 65535 s
    Time after engine start
    Service data
    Initial Engine Coolant Temp
    Initial engine coolant temperature/
    Min.: -40°C, Max.: 119.3°C
    Close to ambient air temperature
    Service data
    Initial Intake Air Temp
    Initial intake air temperature/
    Min.: -40°C, Max.: 119.3°C
    Close to ambient air temperature
    Service data
    Battery Voltage
    Battery voltage/
    Min.: 0 V, Max.: 65.535 V
    11 to 14 V: Idling
    -
    Accelerator Position
    Accelerator pedal position/
    Min.: 0%, Max.: 399.9%
    Actual accelerator pedal position
    -
    Accel Sens. No.1 Volt %
    Absolute Accelerator Pedal Position (APP) No. 1/
    Min.: 0%, Max.: 100%
    10 to 22%: Accelerator pedal is released
    52 to 90%: Accelerator pedal is fully depressed
    -
    Accel Sens. No.2 Volt %
    Absolute APP No. 2/
    Min.: 0%, Max.: 100%
    24 to 40%: Accelerator pedal is released
    68 to 95%: Accelerator pedal is fully depressed
    -
    Accel Sensor Out No.1
    APP sensor No. 1 voltage/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 1.1 V: Accelerator pedal is released
    2.6 to 4.5 V: Accelerator pedal is fully depressed
    -
    Accel Sensor Out No.2
    APP sensor No. 2 voltage/
    Min.: 0 V, Max.: 4.98 V
    1.2 to 2.0 V: Accelerator pedal is released
    3.4 to 4.75 V: Accelerator pedal is fully depressed
    -
    Accelerator Idle Position
    Whether or not accelerator pedal position sensor detecting idle/
    ON or OFF
    ON: Idling
    -
    Accel Fully Close Learn #1
    Accelerator fully closed learning value No. 1/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data
    Accel Fully Close Learn #2
    Accelerator fully closed learning value No. 2/
    Min.: 0 deg, Max.: 124.5 deg
    -
    ETCS service data
    Throttle Sensor Volt %
    Absolute throttle position sensor/
    Min.: 0%, Max.: 100%
    1. 10 to 22%: Throttle fully closed
    2. 64 to 96%: Throttle fully open
    The calculated value based on VTA1.
    Throttl Sensor #2 Volt %
    Throttle sensor position #2/
    Min.: 0%, Max.: 100%
    1. 42 to 62%: Throttle fully closed
    2. 92 to 100%: Throttle fully open
    The calculated value based on VTA2.
    ST1
    Brake pedal signal/
    ON or OFF
    ON: Brake pedal depressed
    -
    System Guard
    System guard/
    ON or OFF
    -
    ETCS service data
    Open Side Malfunction
    Open side malfunction/
    ON or OFF
    -
    ETCS service data
    Throttle Idle Position
    Whether or not throttle position sensor detecting idle/
    ON or OFF
    ON: Accelerator pedal released
    OFF: Accelerator pedal depressed
    -
    Throttle Require Position
    Throttle requirement position/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 1.1 V: Idling
    -
    Throttle Sensor Position*
    Throttle sensor position/
    Min.: 0%, Max.: 100%
    1. 0%: Throttle fully closed
    2. 50 to 80%: Throttle fully open
    Recognition value of throttle opening angle for ECM
    Throttle Position No. 1
    Throttle position sensor No. 1 output voltage/
    Min.: 0 V, Max.: 4.98 V
    1. 0.5 to 1.1 V: Accelerator pedal released
    2. 3.2 to 4.8 V: Accelerator pedal fully depressed
    3. 0.6 to 1.4 V: Fail-safe operating
    -
    Throttle Position No. 2
    Throttle position sensor No. 2 output voltage/
    Min.: 0 V, Max.: 4.98 V
    1. 2.1 to 3.1 V: Accelerator pedal released
    2. 4.6 to 5.0 V: Accelerator pedal fully depressed
    3. 2.1 to 3.1 V: Fail-safe operating
    -
    Throttle Position Command
    Throttle position command value/
    Min.: 0 V, Max.: 4.98 V
    0.5 to 4.8 V
    -
    Throttle Sens Open Pos #1
    Throttle position sensor No. 1/
    Min.: 0 V, Max.: 4.98 V
    0.6 to 1.4 V
    ETCS service data
    Throttle Sens Open Pos #2
    Throttle position sensor No. 2/
    Min.: 0 V, Max.: 4.98 V
    1.7 to 2.5 V
    ETCS service data
    Throttle Motor Current
    Throttle actuator current/
    Min.: 0 A, Max.: 19.9 A
    0 to 3.0 A: Idling
    ETCS service data
    Throttle Motor DUTY
    Throttle actuator/
    Min.: 0%, Max.: 100%
    10 to 22%: Idling
    ETCS service data
    Throttle Motor Duty (Open)
    Throttle actuator duty ratio (open)/
    Min.: 0%, Max.: 255%
    0 to 40%: Idling
    ETCS service data
    Throttle Motor Duty (Close)
    Throttle actuator duty ratio (close)/
    Min.: 0%, Max.: 255%
    0 to 40%: Idling
    ETCS service data
    Throttle Fully Close Learn
    Throttle valve fully closed (learned value)/
    Min.: 0 V, Max.: 4.98 V
    0.4 to 1.0 V: Accelerator pedal released
    -
    +BM Voltage
    +BM voltage/
    Min.: 0 V, Max.: 79.998 V
    11 to 14 V: Ignition switch ON and system normal
    ETCS service data
    Actuator Power Supply
    Actuator power supply/
    ON or OFF
    ON: Idling
    ETCS service data
    Throttle Position
    Throttle valve opening angle/
    Min.: 0 deg, Max.: 499.99 deg
    -
    For use when engine stall, starting problems or rough idle is present.
    ISC Flow
    Flow rate calculated using information from each sensor/
    Min.: 0 L/s, Max.: 79.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    ISC Position
    Requested opening amount calculated using ISC control/
    Min.: 0 deg, Max.: 499.99 deg
    -
    For use when engine stall, starting problems or rough idle is present.
    ISC Feedback Value
    ISC feedback compensation amount/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    ISC Learning Value
    ISC learned compensation amount/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    Electric Load Feedback Val
    Compensation flow rate according to electrical load/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    Air Conditioner FB Val
    Compensation flow rate according to air conditioner load/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    PS Feedback Val
    Compensation flow rate according to power steering load/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    Low Revolution Control
    Low engine speed control operation state/
    ON or OFF
    -
    For use when engine stall, starting problems or rough idle is present.
    Neutral Control
    Neutral control operation state/
    ON or OFF
    -
    For use when engine stall, starting problems or rough idle is present.
    N Range Status
    Shift lever N status/
    ON or OFF
    -
    For use when engine stall, starting problems or rough idle is present.
    Eng Stall Control FB Flow
    Intake air compensation flow rate/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    Deposit Loss Flow
    Flow loss due to deposits/
    Min.: -40 L/s, Max.: 39.99 L/s
    -
    For use when engine stall, starting problems or rough idle is present.
    Fuel Pump Duty
    Fuel pump duty/
    Min.: 0%, Max.: 399.0%
    -
    -
    Injector (Port)
    Injection period of the No. 1 cylinder/
    Min.: 0 μs, Max.: 65535 μs
    1400 to 4000 μs: Idling
    -
    Injection Volum (Cylinder 1)
    Injection volume (cylinder 1)/
    Min.: 0 ml, Max.: 2.047 ml
    0 to 0.5 ml
    Quantity of fuel injection volume for 10 times
    Vacuum Pump
    Key-off EVAP system pump status/
    ON or OFF
    -
    -
    Current Fuel Type
    Status of the current fuel type
    Gasoline/petrol
    -
    EVAP (Purge) VSV
    Purge VSV control duty/
    Min.: 0%, Max.: 100%
    0 to 100%: During idling
    Order signal from ECM
    Evap Purge Flow
    Purge flow/
    Min.: 0%, Max.: 399.9%
    0 to 100%: Idling
    -
    Purge Density Learn Value
    Learning value of purge density/
    Min.: -200, Max.: 199.993
    Idling: -40 to 0
    Service data
    Vapor Pressure Pump
    Vapor pressure/
    Min.: 0 kPa (0 mmHg), Max.: 1441.77 kPa (10814.17 mmHg)
    Approximately 100 kPa (750 mmHg): Ignition switch ON
    EVAP system pressure monitored by canister pressure sensor.
    Vapor pressure (Calculated)
    Calculated EVAP system pressure/
    Min.: -720.896 kPa (-5407.167 mmHg), Max.: 720.874 kPa (5407.002 mmHg)
    Approximately 100 kPa (750 mmHg): Ignition switch ON
    -
    EVAP System Vent Valve
    Key-off EVAP system vent valve status/
    ON or OFF
    -
    -
    EVAP Purge VSV
    VSV status for EVAP control/
    ON or OFF
    -
    -
    Purge Cut VSV Duty
    Purge cut VSV duty/
    Min.: 0%, Max.: 399.9%
    -
    -
    Target Air-Fuel Ratio
    Target Air fuel ratio/
    Min.: 0, Max.: 1.99
    0.8 to 1.2: During idling
    -
    AF Lambda B1S1
    Output air fuel ratio associated with the Bank 1 Sensor 1/
    Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. 1 = Stoichiometric air fuel ratio
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AF Lambda B2S1
    Output air fuel ratio associated with the Bank 2 Sensor 1/
    Min.: 0, Max.: 1.99
    1. Value less than 1 (0.000 to 0.999) = Rich
    2. 1 = Stoichiometric air fuel ratio
    3. Value greater than 1 (1.001 to 1.999) = Lean
    -
    AFS Voltage B1S1
    Air fuel ratio sensor output voltage (for Bank 1 Sensor 1)/
    Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
    AFS Voltage B2S1
    Air fuel ratio sensor output voltage (for Bank 2 Sensor 1)/
    Min.: 0 V, Max.: 7.99 V
    2.8 to 3.8 V: Idling
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
    AFS Current B1S1
    Air fuel ratio sensor current (for Bank 1 Sensor 1)/
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables the technician to check the output current of sensor.
    AFS Current B2S1
    Air fuel ratio sensor current (for Bank 2 Sensor 1)/
    Min.: -128 mA, Max.: 127.99 mA
    -0.5 to 0.5 mA: Idling
    Performing Control the Injection Volume or Control the Injection Volume for A/F Sensor function of Active Test enables the technician to check the output current of sensor.
    A/F Heater Duty #1
    A/F heater duty ratio (for Bank 1)
    Min.: 0%, Max.: 399.9%
    0 to 100%
    -
    A/F Heater Duty #2
    A/F heater duty ratio (for Bank 2)
    Min.: 0%, Max.: 399.9%
    0 to 100%
    -
    O2S B1S2
    Heated oxygen sensor output voltage (for Bank 1 Sensor 2)/
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving at 70 km/h (44 mph)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
    O2S B2S2
    Heated oxygen sensor output voltage (for Bank 2 Sensor 2)/
    Min.: 0 V, Max.: 1.275 V
    0.1 to 0.9 V:
    Driving at 70 km/h (44 mph)
    Performing the Control the Injection Volume or Control the Injection Volume for A/F Sensor function of the Active Test enables the technician to check voltage output of the sensor.
    O2S Impedance B1S2
    Sub heated oxygen sensor impedance (Bank 1 Sensor 2)/
    Min.: 0 ohm, Max.: 21247.67 ohm
    5 to 15000 ohm
    After driving approx. 10 min. in urban area
    O2S Impedance B2S2
    Sub heated oxygen sensor impedance (Bank 2 Sensor 2)/
    Min.: 0 ohm, Max.: 21247.67 ohm
    5 to 15000 ohm
    After driving approx. 10 min. in urban area
    O2 Heater B1S2
    Heated oxygen sensor heater (for Bank 1 Sensor 2)/
    Active or Not Act
    -
    -
    O2 Heater B2S2
    Heated oxygen sensor heater (for Bank 2 Sensor 2)/
    Active or Not Act
    -
    -
    O2 Heater Curr Val B1S2
    Heated oxygen sensor current (for Bank 1 Sensor 2)/
    Min.: 0 A, Max.: 4.9 A
    -
    -
    O2 Heater Curr Val B2S2
    Heated oxygen sensor current (for Bank 2 Sensor 2)/
    Min.: 0 A, Max.: 4.9 A
    -
    -
    Short FT #1
    Short-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
    Long FT #1
    Long-term fuel trim of bank 1/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    1. This item refers to the overall fuel compensation carried out in long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
    2. Air fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #1" indicates the learned value for the current operating range. [A/F Learn Value Idle #1], [A/F Learn Value Low #1], [A/F Learn Value Mid1 #1], [A/F Learn Value Mid2 #1] and [A/F Learn Value High #1] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #1" indicates the current engine operating range.
    A/F Learn Value Idle #1
    Air fuel ratio learned value for idling (for Bank 1)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
    A/F Learn Value Low #1
    Air fuel ratio learned value for low engine loads (for Bank 1)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
    A/F Learn Value Mid1 #1
    Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 1)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the low load range (when the range of engine loads is divided into four parts).
    A/F Learn Value Mid2 #1
    Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 1)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the high load range (when the range of engine loads is divided into four parts).
    A/F Learn Value High #1
    Air fuel ratio learned value for high engine loads (for Bank 1)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
    Total FT #1
    Total fuel trim of bank 1/
    Min.: -0.5, Max.: 0.496
    -0.2 to 0.2: Idling
    -
    Short FT #2
    Short-term fuel trim of bank 2/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    This item refers to the short-term fuel compensation used to maintain the air fuel ratio at the stoichiometric air-fuel ratio.
    Long FT #2
    Long-term fuel trim of bank 2/
    Min.: -100%, Max.: 99.2%
    -20 to +20%
    1. This item refers to the overall fuel compensation carried out in long-term to compensate for a continual deviation of the short-term fuel trim from the central value.
    2. Air-fuel ratio feedback learning is divided up according to the engine operating range (engine speed x load), and separate values are stored for each operating range. "Long FT #2" indicates the learned value for the current operating range. [A/F Learn Value Idle #2], [A/F Learn Value Low #2], [A/F Learn Value Mid1 #2], [A/F Learn Value Mid2 #2] and [A/F Learn Value High #2] indicate the leaned values for the different operating ranges. The learned value that is the same as "Long FT #2" indicates the current engine operating range.
    A/F Learn Value Idle #2
    Air fuel ratio learned value for idling (for Bank 2)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when idling with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher).
    A/F Learn Value Low #2
    Air fuel ratio learned value for low engine loads (for Bank 2)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the low load range (when the range of engine loads is divided into four parts).
    A/F Learn Value Mid1 #2
    Air fuel ratio learned value for mid-sized engine loads 1 (for Bank 2)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the low load range (when the range of engine loads is divided into four parts).
    A/F Learn Value Mid2 #2
    Air fuel ratio learned value for mid-sized engine loads 2 (for Bank 2)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the midsize load range closer to the high load range (when the range of engine loads is divided into four parts).
    A/F Learn Value High #2
    Air fuel ratio learned value for high engine loads (for Bank 2)/
    Min.: -50%, Max.: 49.6%
    -20 to +20%
    Learning is performed when driving with the engine warmed up (engine coolant temperature is 75°C [167°F] or higher) and operating in the high load range (when the range of engine loads is divided into four parts).
    Total FT #2
    Total fuel trim of bank 2/
    Min.: -0.5, Max.: 0.496
    -0.2 to 0.2: Idling
    -
    Fuel System Status #1
    Fuel system status (Bank 1)/
    OL, CL, OL Drive, OL Fault or CL Fault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
    2. CL (Closed Loop): Using A/F sensor as feedback for fuel control.
    3. OL Drive: Open loop due to driving conditions (fuel enrichment).
    4. OL Fault: Open loop due to detected system fault.
    5. CL Fault: Closed loop but A/F sensor, used for fuel control, malfunctioning.
    Fuel System Status #2
    Fuel system status (Bank 2)/
    OL, CL, OL Drive, OL Fault or CL Fault
    CL: Idling after warming up
    1. OL (Open Loop): Has not yet satisfied conditions to go to closed loop.
    2. CL (Closed Loop): Using A/F sensor as feedback for fuel control.
    3. OL Drive: Open loop due to driving conditions (fuel enrichment).
    4. OL Fault: Open loop due to detected system fault.
    5. CL Fault: Closed loop but A/F sensor, used for fuel control, malfunctioning.
    Air pump pressure (Absolute)
    Air pump pressure (absolute) for Bank 1/
    Min.: 0 kPa, Max.: 65535 kPa
    Atmospheric pressure +1 kPa or more: Air pump ON, air switching valve open
    Close to atmospheric pressure: Air pump OFF, air switching valve closed
    Refer to DTC P2431
    (Click here)
    Air Pump2 Pressure (Absolute)
    Air pump pressure (absolute) for Bank 2/
    Min.: 0 kPa, Max.: 65535 kPa
    Atmospheric pressure +1 kPa or more: Air pump ON, air switching valve open
    Close to atmospheric pressure: Air pump OFF, air switching valve closed
    Refer to DTC P2431
    (Click here)
    Air Pump Pulsation Pressure
    Air pump pulsation pressure for Bank 1/
    Min.: 0 kPa, Max.: 655.35 kPa
    -
    Cumulative pulsation pressure calculated by ECM
    (Click here)
    Air Pump2 Pulsation Pressure
    Air pump pulsation pressure for Bank 2/
    Min.: 0 kPa, Max.: 655.35 kPa
    -
    Cumulative pulsation pressure calculated by ECM
    (Click here)
    Secondary Air Control VSV
    Secondary air injection system status/
    ON or OFF
    ON: Secondary air injection system operating
    -
    2nd Air System Status
    Secondary air system status/
    ON or OFF
    ON: Secondary air system operating
    -
    AI Test
    AI operation prohibition/
    READY or NOT RDY
    READY
    -
    IGN Advance
    Ignition timing advance for No. 1 cylinder/
    Min.: -64 deg., Max.: 63.5 deg.
    BTDC 5 to 15°: Idling
    -
    Knock Feedback Value
    Feedback value of knocking/
    Min.: -1024° CA, Max.: 1023.9° CA
    -22 to 0° CA:
    Driving at 70 km/h (44 mph)
    Service data
    Knock Correct Learn Value
    Correction learning value of knocking/
    Min.: -1024° CA, Max.: 1023.9° CA
    0 to 25° CA:
    Driving at 70 km/h (44 mph)
    Service data
    Idle Spark Advn Ctrl #1
    Individual cylinder timing advance compensation amount (No. 1)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    For use when engine stall, starting problems or rough idle is present.
    Idle Spark Advn Ctrl #2
    Individual cylinder timing advance compensation amount (No. 2)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    For use when engine stall, starting problems or rough idle is present.
    Idle Spark Advn Ctrl #3
    Individual cylinder timing advance compensation amount (No. 3)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    For use when engine stall, starting problems or rough idle is present.
    Idle Spark Advn Ctrl #4
    Individual cylinder timing advance compensation amount (No. 4)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    For use when engine stall, starting problems or rough idle is present.
    Idle Spark Advn Ctrl #5
    Individual cylinder timing advance compensation amount (No. 5)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    For use when engine stall, starting problems or rough idle is present.
    Idle Spark Advn Ctrl #6
    Individual cylinder timing advance compensation amount (No. 6)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    For use when engine stall, starting problems or rough idle is present.
    Idle Spark Advn Ctrl #7
    Individual cylinder timing advance compensation amount (No. 7)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    For use when engine stall, starting problems or rough idle is present.
    Idle Spark Advn Ctrl #8
    Individual cylinder timing advance compensation amount (No. 8)/
    Min.: 0° CA, Max.: 15.93° CA
    -
    For use when engine stall, starting problems or rough idle is present.
    ACIS VSV
    VSV status for ACIS control/
    ON or OFF
    -
    Active Test support data
    Target EGR Position
    EGR valve target opening amount/
    Min.: 0%, Max.: 100%
    Changes according to engine speed and load: Driving
    -
    EGR Step Position
    EGR step position/
    Min.: 0 step, Max.: 255 step
    Changes according to engine speed and load: Driving
    0 step: Shift lever in D after racing the engine with shift lever in N
    -
    VVT Control Status #1
    Variable valve timing (VVT) control status (Bank 1)/
    ON or OFF
    -
    -
    VVT Control Status #2
    VVT control status (Bank 2)/
    ON or OFF
    -
    -
    VVT Advance Fail
    VVT control failure status/
    ON or OFF
    ON: VVT control failure
    -
    VVT Aim Angle #1*2
    VVT target duty (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0%: Idling
    VVT duty signal value during forced operation.
    VVT Change Angle #1*2
    VVT change angle (Bank 1)/
    Min.: 0° FR, Max.: 639.9° FR
    0 to 5° FR: Idling
    Displacement angle during forced operation.
    VVT OCV Duty #1*2
    VVT OCV operation duty (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0%: Idling
    Requested duty value for forced operation.
    VVT Aim Angle #2*2
    VVT target duty (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0%: Idling
    VVT duty signal value during forced operation.
    VVT Change Angle #2*2
    VVT change angle (Bank 2)/
    Min.: 0° FR, Max.: 639.9° FR
    0 to 5° FR: Idling
    Displacement angle during forced operation.
    VVT OCV Duty #2*2
    VVT OCV operation duty (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0%: Idling
    Requested duty value for forced operation.
    VVT Ex Hold Lrn Val #1*2
    VVT exhaust hold duty ratio learning value (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 80%: Idling
    -
    VVT Ex Chg Angle #1*2
    VVT exhaust change angle (Bank 1)/
    Min.: 0°FR, Max.: 639.9°FR
    0 to 40°FR: Idling
    Displacement angle during forced operation.
    VVT Ex OCV Duty #1*2
    VVT exhaust OCV duty (Bank 1)/
    Min.: 0%, Max.: 399.9%
    0 to 100%: Idling
    Requested duty value for forced operation.
    VVT Ex Hold Lrn Val #2*2
    VVT exhaust hold duty ratio learning value (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 80%: Idling
    -
    VVT Ex Chg Angle #2*2
    VVT exhaust change angle (Bank 2)/
    Min.: 0°FR, Max.: 639.9°FR
    0 to 40°FR: Idling
    Displacement angle during forced operation.
    VVT Ex OCV Duty #2*2
    VVT exhaust OCV duty (Bank 2)/
    Min.: 0%, Max.: 399.9%
    0 to 100%: Idling
    Requested duty value for forced operation.
    VN Turbo Type
    VN turbo type/
    Not Avl, Commo, Vacuum or CAN Com
    Not Avl
    -
    Catalyst Temp B1S1
    Catalyst temperature (Bank 1, Sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B2S1
    Catalyst temperature (Bank 2, Sensor 1)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B1S2
    Catalyst temperature (Bank 1, Sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Catalyst Temp B2S2
    Catalyst temperature (Bank 2, Sensor 2)/
    Min.: -40°C, Max.: 6513.5°C
    -
    -
    Starter Signal
    Starter signal/
    ON or OFF
    ON: Cranking
    -
    Starter Control
    Starter switch status/
    Open or Close
    Open: Cranking
    -
    Power Steering Signal
    Power steering switch signal/ ON or OFF
    ON: Power steering operating
    -
    Starter Relay
    Starter relay status/
    ON or OFF
    ON: Cranking
    -
    ACC Relay
    ACC relay status/
    ON or OFF
    ON: Cranking
    -
    Neutral Position SW Signal
    PNP switch status/
    ON or OFF
    ON: P or N position
    -
    Transfer Neutral
    Neutral status of the transfer/
    ON or OFF
    ON: 4WD control switch in 2WD position
    -
    Transfer L4
    L4 status of the transfer/
    ON or OFF
    ON: 4WD control switch in 4L position
    -
    Stop Light Switch
    Stop light switch/
    ON or OFF
    ON: Brake pedal is depressed
    -
    A/C Signal
    A/C switch status/
    ON or OFF
    ON: A/C ON
    -
    Closed Throttle Position SW
    Closed throttle position switch/
    ON or OFF
    1. ON: Throttle fully closed
    2. OFF: Throttle open
    -
    Fuel Cut Condition
    Fuel cut condition/
    ON or OFF
    ON: Fuel cut operating
    -
    Immobiliser Communication
    Immobiliser communication/
    ON or OFF
    ON: Normal
    -
    Check Mode
    Check mode/
    ON or OFF
    ON: Check mode ON
    Refer to Check Mode Procedure (Click here).
    SPD Test Result
    Check mode result for vehicle speed sensor/
    Compl or Incmpl
    -
    -
    AS Test Result
    Check mode result for secondary air injection system/
    Compl or Incmpl
    -
    -
    Misfire Test Result
    Check mode result for misfire monitor/
    Compl or Incmpl
    -
    -
    OXS1 Test Result
    Check mode result for heated oxygen sensor (Bank 1)/
    Compl or Incmpl
    -
    -
    OXS2 Test Result
    Check mode result for heated oxygen sensor (Bank 2)/
    Compl or Incmpl
    -
    -
    A/F Test Results #2
    Check mode result for air fuel ratio sensor (Bank 2)/
    Compl or Incmpl
    -
    -
    A/F Test Results #1
    Check mode result for air fuel ratio sensor (Bank 1)/
    Compl or Incmpl
    -
    -
    Complete Parts Monitor
    Comprehensive component monitor/
    Not Avl or Avail
    -
    -
    Fuel System Monitor
    Fuel system monitor/
    Not Avl or Avail
    -
    -
    Misfire Monitor
    Misfire monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Not Avl or Avail
    -
    -
    EGR/VVT Monitor
    EGR/VVT monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Heater Monitor
    O2S (A/FS) heater monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Not Avl or Avail
    -
    -
    O2S(A/FS) Monitor
    O2S (A/FS) monitor/
    Compl or Incmpl
    -
    -
    A/C Monitor
    A/C monitor/
    Not Avl or Avail
    -
    -
    A/C Monitor
    A/C monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Not Avl or Avail
    -
    -
    2nd Air Monitor
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor
    EVAP monitor/
    Not Avl or Avail
    -
    -
    EVAP Monitor
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Not Avl or Avail
    -
    -
    Heated Catalyst Monitor
    Heated catalyst monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Not Avl or Avail
    -
    -
    Catalyst Monitor
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    Component Monitor ENA
    Comprehensive component monitor/
    Unable or Enable
    -
    -
    Component Monitor CMPL
    Comprehensive component monitor/
    Compl or Incmpl
    -
    -
    Fuel System Monitor ENA
    Fuel system monitor/
    Unable or Enable
    -
    -
    Fuel System Monitor CMPL
    Fuel system monitor/
    Compl or Incmpl
    -
    -
    Misfire Monitor ENA
    Misfire monitor/
    Unable or Enable
    -
    -
    Misfire Monitor CMPL
    Misfire monitor/
    Compl or Incmpl
    -
    -
    EGR/VVT Monitor ENA
    EGR monitor/
    Unable or Enable
    -
    -
    EGR/VVT Monitor CMPL
    EGR monitor/
    Compl or Incmpl
    -
    -
    Heater Monitor ENA
    O2S (A/FS) heater monitor/
    Unable or Enable
    -
    -
    Heater Monitor CMPL
    O2S (A/FS) heater monitor/
    Compl or Incmpl
    -
    -
    O2S(A/FS) Monitor ENA
    O2S (A/FS) monitor/
    Unable or Enable
    -
    -
    O2S(A/FS) Monitor CMPL
    O2S (A/FS) monitor/
    Compl or Incmpl
    -
    -
    A/C Monitor ENA
    A/C monitor/
    Unable or Enable
    -
    -
    A/C Monitor CMPL
    A/C monitor/
    Compl or Incmpl
    -
    -
    2nd Air Monitor ENA
    2nd air monitor/
    Unable or Enable
    -
    -
    2nd Air Monitor CMPL
    2nd air monitor/
    Compl or Incmpl
    -
    -
    EVAP Monitor ENA
    EVAP monitor/
    Unable or Enable
    -
    -
    EVAP Monitor CMPL
    EVAP monitor/
    Compl or Incmpl
    -
    -
    Heated Cat Monitor ENA
    Heated catalyst monitor/
    Unable or Enable
    -
    -
    Heated Cat Monitor CMPL
    Heated catalyst monitor/
    Compl or Incmpl
    -
    -
    Catalyst Monitor ENA
    Catalyst monitor/
    Unable or Enable
    -
    -
    Catalyst Monitor CMPL
    Catalyst monitor/
    Compl or Incmpl
    -
    -
    TC Terminal
    TC terminal status/
    ON or OFF
    -
    -
    # Codes (Include History)
    Number of codes/
    Min.: 0, Max.: 255
    -
    Number of detected DTCs
    MIL
    MIL status/
    ON or OFF
    ON: MIL ON
    -
    MIL ON Run Distance
    MIL ON run distance/
    Min.: 0 km, Max.: 65535 km
    Distance after DTC detected
    -
    Running Time from MIL ON
    Running time from MIL ON/
    Min.: 0 min, Max.: 65535 min
    Running time after MIL turned ON
    -
    Time after DTC Cleared
    Time after DTCs cleared/
    Min.: 0 min, Max.: 65535 min
    Time after DTCs were cleared
    -
    Distance from DTC Cleared
    Distance after DTCs cleared/
    Min.: 0 km, Max.: 65535 km
    Driving distance after DTCs were cleared
    -
    Warmup Cycle Cleared DTC
    Warm-up cycles after DTCs cleared/
    Min.: 0, Max.: 255
    -
    Number of warm-up cycles after DTCs cleared
    Dist Batt Cable Disconnect
    Distance after battery cable disconnected/
    Min.: 0 km, Max.: 65535 km
    Total distance vehicle driven after battery cable disconnected
    -
    IG OFF Elapsed Time
    Time after ignition switch off/
    Min.: 0 min, Max.: 655350 min
    Cumulative time after ignition switch off
    -
    OBD Requirements
    OBD requirement
    OBD2
    -
    Number of Emission DTC
    Emission related DTCs
    -
    Number of emission related DTCs
    TC and TE1
    TC and CG (TE1) terminals of DLC3/
    ON or OFF
    -
    -
    Ignition Trig. Count
    Ignition counter/
    Min.: 0, Max.: 65535
    0 to 800
    -
    Cylinder #1 Misfire Count
    to
    Cylinder #8 Misfire Count
    Misfire count of cylinder 1 to 8/
    Min.: 0, Max.: 255
    0
    This item displayed only when idling engine.
    All Cylinders Misfire Count
    All cylinders misfire count/
    Min.: 0, Max.: 255
    0 to 35
    -
    Multi Cylinders Misfire Count
    Multiple cylinder misfire count/
    Min.: 0, Max.: 65535
    0 to 65535
    -
    Misfire RPM
    Engine RPM for first misfire range/
    Min.: 0 rpm, Max.: 6375 rpm
    0 rpm: Misfire 0
    -
    Misfire Load
    Engine load for first misfire range/
    Min.: 0 g/rev, Max.: 3.98 g/rev
    0 g/rev: Misfire 0
    -
    Misfire Margin
    Misfire monitoring/
    Min.: -128%, Max.: 127%
    -100 to 99.2%
    Misfire detection margin
    Catalyst OT MF F/C
    Catalyst over temperature misfire prevention F/C/
    Not Avl or Avail
    Avail: Cat OT MF F/C available
    Not Avl: Cat OT MF F/C not available
    -
    Cat OT MF F/C History
    Catalyst over temperature misfire prevention F/C history/
    ON or OFF
    ON: Fuel cut operation history exists
    -
    Cat OT MF F/C Cylinder #1
    Display of fuel cut operation in No. 1 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #2
    Display of fuel cut operation in No. 2 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #3
    Display of fuel cut operation in No. 3 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #4
    Display of fuel cut operation in No. 4 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #5
    Display of fuel cut operation in No. 5 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #6
    Display of fuel cut operation in No. 6 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #7
    Display of fuel cut operation in No. 7 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut is operating
    -
    Cat OT MF F/C Cylinder #8
    Display of fuel cut operation in No. 8 cylinder (if certain level of misfire malfunction is detected)/
    ON or OFF
    ON: Fuel cut is operating
    -
    Engine Speed (Starter Off)
    Engine speed when starter off/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    For use when engine stall, starting problems or rough idle is present.
    Starter Count
    Number of times starter turned on after ignition switch turned to ON/
    Min.: 0, Max.: 255
    -
    For use when engine stall, starting problems or rough idle is present.
    Run Dist of Previous Trip
    Distance driven during previous trip/
    Min.: 0 km, Max.: 655.35 km
    -
    Before 5 seconds elapse after starting the engine, which is the DTC P1604 (Startability Malfunction) detection duration, this parameter indicates the distance driven during the previous trip.
    After 5 seconds elapse after starting the engine, this parameter indicates the distance driven during the current trip calculated from the vehicle speed signal.

    HINT:
    Run Dist of Previous Trip in the freeze frame data present when the startability malfunction occurred (DTC P1604 detected) indicates the distance driven during the previous trip, but in all other cases, such as for the snapshot data of the Data List (real-time measurements), or for freeze frame data present when DTCs other than P1604 were detected, the value indicates the distance driven during the current trip.

    Engine Starting Time
    Time elapsed after engine started (interval between ignition switch ON and off)/
    Min.: 0 ms, Max.: 655350 ms
    -
    For use when engine stall, starting problems or rough idle is present.
    Previous Trip Coolant Temp
    Engine coolant temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Previous Trip Intake Temp
    Intake air temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Engine Oil Temperature
    Engine oil temperature (estimated temperature)/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Previous Trip Eng Oil Temp
    Engine oil temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Ambient Temp for A/C
    Ambient temperature for A/C/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Previous Trip Ambient Temp
    Ambient temperature during previous trip/
    Min.: -40°C, Max.: 215°C
    -
    For use when engine stall, starting problems or rough idle is present.
    Engine Start Hesitation
    History of hesitation during engine start/
    ON or OFF
    -
    -
    Low Rev for Eng Start
    History of low engine speed after engine start/
    ON or OFF
    -
    -
    Minimum Engine Speed
    Minimum engine speed/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    For use when engine stall, starting problems or rough idle is present.
    Power Steering Pressure
    Power steering oil pressure/
    Min.: 0 MPa, Max.: 25.599 MPa
    -
    -
    ACT VSV
    A/C cut status for Active Test/
    ON or OFF
    -
    Active Test support data
    Idle Fuel Cut
    Fuel cut at idle/
    ON or OFF
    ON: Fuel cut operating
    Idle Fuel Cut = "ON" when throttle valve fully closed and engine speed over 2800 rpm.
    FC TAU
    Fuel cut TAU: Fuel cut during very light load/
    ON or OFF
    ON: Fuel cut operating
    The fuel cut being performed under very light load to prevent the engine combustion from becoming incomplete.
    Immobiliser Fuel Cut
    Status of the immobiliser fuel cut/
    ON or OFF
    -
    -
    Immobiliser Fuel Cut History
    Status of the immobiliser fuel cut history/
    ON or OFF
    -
    -
    Electrical Load Signal 1
    Electrical load signal/
    ON or OFF
    -
    -
    Electrical Load Signal 2
    Electrical load signal/
    ON or OFF
    -
    -
    Cruise Cancel Signal
    Status of the cruise cancel signal/
    ON or OFF
    -
    -
    Model Code
    Model code
    -
    Used for identifying the model code:
    UPK5##
    Engine Type
    Engine type
    -
    Used for identifying the engine type:
    1URFE
    Cylinder Number
    Number of cylinders/
    Min.: 0, Max.: 255
    -
    Used for identifying number of cylinders:
    8
    Destination
    Destination
    -
    Used for identifying the destination:
    A (America)
    Model Year
    Model year/
    Min.: 1900, Max.: 2155
    -
    Used for identifying the model year:
    20##
    Engine Speed of Cyl #1
    Engine RPM for cylinder 1/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #2
    Engine RPM for cylinder 2/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #3
    Engine RPM for cylinder 3/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #4
    Engine RPM for cylinder 4/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #5
    Engine RPM for cylinder 5/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #6
    Engine RPM for cylinder 6/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #7
    Engine RPM for cylinder 7/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Engine Speed of Cyl #8
    Engine RPM for cylinder 8/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    Av Engine Speed of All Cyl
    Engine RPM for all cylinders/
    Min.: 0 rpm, Max.: 51199 rpm
    -
    Output only when Check the Cylinder Compression is performed using Active Test.
    SPD (NT)
    Input shaft speed/
    Min.: 0 rpm, Max.: 12750 rpm
    Lock-up is:
    1. ON (after warming up engine): Input turbine speed (NT) is equal to engine speed
    2. OFF (idling with shift lever in N): Input turbine speed (NT) is nearly equal to engine speed
    Data is displayed in increments of 50 rpm
    SPD (SP2)
    Output shaft speed/
    Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)
    Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed)
    -
    Shift SW Status (P Range)
    PNP switch status (P Range)/
    ON or OFF
    Shift lever is:
    1. In P: ON
    2. Not in P: OFF
    When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (R Range)
    PNP switch status (R Range)/
    ON or OFF
    Shift lever is:
    1. In R: ON
    2. Not in R: OFF
    When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Shift SW Status (N Range)
    PNP switch status (N Range)/
    ON or OFF
    Shift lever is:
    1. In N: ON
    2. Not in N: OFF
    When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    Sports Shift Up SW
    Sport shift up switch status/
    ON or OFF
    1. ON: Shift lever held in "+" (up-shift)
    2. OFF: Shift lever not in "+" (up-shift)
    -
    Sports Shift Down SW
    Sport shift down switch status/
    ON or OFF
    1. ON: Shift lever held in "-" (down-shift)
    2. OFF: Shift lever not in "-" (down-shift)
    -
    Sports Mode Selection SW
    Sport mode select switch status/
    ON or OFF
    Shift lever is:
    1. ON: In S, "+" or "-"
    2. OFF: Not in S, "+" or "-"
    -
    Shift SW Status (D Range)
    PNP switch status (D Range)/
    ON or OFF
    Shift lever is:
    1. In D, S, "+" or "-": ON
    2. Not in D, S, "+" or "-": OFF
    When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
    A/T Oil Temperature 1
    No. 1 ATF temperature sensor value/
    Min.: -40°C, Max.: 215°C
    1. After stall test:
      Approximately 80°C (176°F)
    2. Equal to ambient temperature while engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or shorted
    A/T Oil Temperature 2
    No. 2 ATF temperature sensor value/
    Min.: -40°C, Max.: 215°C
    1. After stall test:
      Approximately 80°C (176°F)
    2. Equal to ambient temperature while engine is cold
    If value is -40°C (-40°F) or 215°C (419°F), No. 2 ATF temperature sensor circuit is open or shorted
    Lock Up
    Lock-up/
    ON or OFF
    Lock-up is:
    1. Operating: ON
    2. Not operating: OFF
    -
    Shift Status
    ECM gear shift command/
    1st, 2nd, 3rd, 4th, 5th or 6th
    Shift lever is:
    1. In D: 1st, 2nd, 3rd, 4th, 5th or 6th
    2. In S: 1st, 2nd, 3rd, 4th, 5th or 6th
    -
    SLT Solenoid Status
    Shift solenoid SLT status/
    ON or OFF
    Shift solenoid SLT is:
    1. Accelerator pedal is depressed: OFF
    2. Accelerator pedal is released: ON
    -
    SLU Solenoid Status
    Shift solenoid SLU status/
    ON or OFF
    Shift solenoid SLU is:
    1. Operating: ON
    2. Not operating: OFF
    -
    AT Fluid
    Flex lock-up judder judgment/
    ON or OFF
    1. ON: Judder judgment occurs
    2. OFF: Judder judgment does not occur
    -

HINT:
  1. *1: Excluding throttle valve opening percentage due to Idle Speed Control (ISC).
  2. *2: Data List values are only displayed when performing the following Active test: Control the VVT Linear (Bank 1), Control the VVT Linear (Bank 2), Control the Exhaust Linear (Bank 1) and Control the VVT Exhaust Linear (Bank 2). For other Active test, the Data List value will be 0.
  3. Normal Condition: If no conditions are specifically stated for "idling", the shift lever should be in N or P, the A/C switch should be OFF, and all accessory switches should be OFF.


ACTIVE TEST

HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the Techstream to the DLC3.

  4. Turn the ignition switch to ON.

  5. Turn the Techstream on.

  6. Enter the following menus: Powertrain / Engine and ECT / Active Test.

  7. According to the display on the Techstream, perform the Active Test.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Control the Injection Volume
    Change injection volume
    Between -12.5% and 24.8%
    1. All injectors tested at the same time.
    2. Perform test at or below 3000 rpm.
    3. Injection volume can be changed in 1% gradations within control range.
    Control the Injection Volume for A/F Sensor
    Change injection volume
    -12.5%/0%/12.5%
    1. Perform test at or below 3000 rpm.
    2. Control the Injection Volume for A/F Sensor enables checking and graphing of A/F (Air Fuel Ratio) sensor voltage outputs.
    3. To conduct test, enter the following menus: Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2SB2 S2.
    Control the EGR Step Position
    Open or close EGR valve
    0 to 110 steps
    1. EGR valve is fully closed at step position 0, and fully open at step position 110.
    2. Amount of EGR gas flowing into the intake manifold varies in accordance with the EGR valve opening angle.
    3. Perform this test when the following conditions are met:
      1. Vehicle is stopped.
      2. Engine is running.
    4. Do not leave the EGR valve open for 10 seconds or more during the Active Test.
    5. Be sure to return the EGR valve to step 0 when the Active Test is completed.
    6. Do not open the EGR valve 30 steps or more during the Active Test.
    Activate the VSV for Secondary Air Control
    Activate the Secondary Air System
    ON/OFF
    1. Do not perform test for 5 seconds or more.
    2. After test, do not perform test again for 30 seconds.
    Activate the VSV for Intake Control
    Activate VSV for intake control
    ON/OFF
    -
    Activate the VSV for Evap Control
    Activate purge VSV control
    ON/OFF
    -
    Control the A/C Cut Signal
    Control A/C cut signal
    ON/OFF
    -
    Control the Fuel Pump / Speed
    Activate fuel pump
    ON/OFF
    This test is possible when the following conditions are met:
    1. Ignition switch ON.
    2. Engine not started.
    3. Shift lever in P.
    Control the Fuel Pump Duty
    Activate fuel pump
    25%/ 80%
    This test is possible when the following conditions are met:
    1. Ignition switch ON.
    2. Engine not started.
    3. Shift lever in P.
    Connect the TC and TE1
    Turn on and off TC and TE1 connection
    ON/OFF
    1. ON: TC and TE1 connected.
    2. OFF: TC and TE1 disconnected.
    Control the Idle Fuel Cut Prohibit
    Prohibit idling fuel cut control
    ON/OFF
    -
    Prohibit the Catalyst OT Misfire prevent F/C
    Prohibit catalyst overheat malfunction prevention fuel cut operation during misfire
    ON: Fuel cut is prohibited
    Confirm that the vehicle is stopped and the engine speed is 3000 rpm or less.
    Activate the Starter Relay
    Activate the starter relay
    ON/OFF
    Perform this test with the engine stopped.
    Activate the ACC Cut Relay
    Activate the ACC CUT relay
    ON/OFF
    Perform this test with the engine stopped.
    Control the ETCS Open/Close Slow Speed
    Throttle actuator
    Close/Open
    Open: Throttle valve opens slowly
    This test is possible when the following conditions are met:
    1. Ignition switch ON.
    1. Engine not started.
    1. Fully depressing accelerator pedal (APP: 58 degrees or more).
    2. Shift lever in P.
    Control the ETCS Open/Close Fast Speed
    Throttle actuator
    Close/Open
    Open: Throttle valve opens quickly
    Same as above.
    Control the VVT Linear (Bank 1)
    Control Variable Valve Timing (VVT) [Bank 1]
    -128 to 127% (This value added to present OCV control duty)
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stall or rough idle when VVT actuator operated by 100%.
    2. Test possible during idle.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT System (Bank 1)
    Turn Oil Control Valve (OCV) on and off
    ON/OFF
    1. Engine stalls or idles roughly when OCV turned ON.
    2. Normal engine running or idling when OCV OFF.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT Linear (Bank 2)
    Control Variable Valve Timing (VVT) [Bank 2]
    -128 to 127% (This value added to present OCV control duty)
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stall or rough idle when VVT actuator operated by 100%.
    2. Test possible during idle.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT System (Bank 2)
    Turn Oil Control Valve (OCV) on and off
    ON/OFF
    1. Engine stalls or idles roughly when OCV turned ON.
    2. Normal engine running or idling when OCV OFF.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT Exhaust Linear (Bank 1)
    Control VVT (Bank 1)
    -128 to 127% (This value added to present OCV control duty)
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stall or rough idle when VVT actuator operated by 100%.
    2. Test possible while engine idling.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Control the VVT Exhaust Linear (Bank 2)
    Control VVT (Bank 2)
    -128 to 127% (This value added to present OCV control duty)
    100%: Maximum advance
    -100%: Maximum retard
    1. Engine stall or rough idle when VVT actuator operated by 100%.
    2. Test possible while engine idling.
    3. DTCs related to the VVT system may be stored due to Active Test operation, but this does not indicate a malfunction.
    Activate the Vacuum Pump
    Activate leak detection pump (built into canister pump module)
    ON/OFF
    -
    Activate the VSV for Vent Valve
    Activate vent valve (built into canister pump module)
    ON/OFF
    -
    Control the Select Cylinder Fuel Cut
    Selected cylinder (cylinder #1 to #8) injection fuel cut
    #1/#2/#3/#4/#5/#6/#7/#8
    ON/OFF
    Test possible while vehicle stopped and engine idling*1.
    Control the All Cylinders Fuel Cut
    All cylinder fuel cut
    ON/OFF
    Test possible while vehicle stopped and engine idling*1.
    Check the Cylinder Compression*2
    Check the cylinder compression pressure
    ON/OFF
    Fuel injection and ignition stop in all cylinders.

    NOTICE:
    *1:
    1. If the display of the Data List's Catalyst OT MF F/C item is Not Avl, perform this Active Test with the vehicle stopped and the engine idling.
    2. If the display of the Data List's Catalyst OT MF F/C item is Avail, perform this Active Test as described below.
      1. Stop the engine, turn the ignition switch ON.
      2. Enter the Control the Select Cylinder Fuel Cut.
      3. Select the cylinder for fuel cut (cylinder #1 to #8) and turn the Active Test ON (press the RIGHT or LEFT button).
      4. Start the engine.

    HINT:
    *2: When cranking the engine, each cylinder measures the engine speed.
    In this Active Test, the fuel and ignition of all cylinders is cut. The engine must then be cranked for approximately 10 seconds. At this time, the speed of each cylinder is measured. If the speed of one cylinder is more than the other cylinders, it can be determined that the compression pressure of that cylinder is lower than the other cylinders.

    1. Warm up the engine.
    2. Turn the ignition switch off.
    3. Connect the Techstream to the DLC3.
    4. Turn the ignition switch to ON.
    5. Turn the Techstream on.
    6. Enter the following menus: Powertrain / Engine and ECT / Active Test / Check the Cylinder Compression.

      HINT:
      To display the entire Data List, press the pull down menu button next to Primary. Then select Compression.

    7. Push the snapshot button to turn the snapshot function on.

      HINT:
      Using the snapshot function, data can be recorded during the Active Test.

    8. While the engine is not running, press the RIGHT or LEFT button to change Check the Cylinder Compression to ON.

      HINT:
      After performing the above procedure, Check the Cylinder Compression will start. Fuel injection for all cylinders is prohibited and each cylinder engine speed measurement enters standby mode.

    9. Crank the engine for about 10 seconds.

      HINT:
      Continue to crank the engine until the values change from the default value (51199 rpm).

    10. Monitor the engine speed (Engine Speed of Cyl #1 to #8) displayed on the Techstream.

      HINT:
      At first, the Techstream displays extremely high cylinder engine speed values. After approximately 10 seconds of engine cranking, each cylinder engine speed measurement will change to the actual engine speed.

      NOTICE:
      1. Do not crank the engine continuously for 20 seconds or more.
      2. If it is necessary to crank the engine again after Check the Cylinder Compression has been changed to ON and the engine has been cranked once, press Exit to return to the Active Test menu screen. Then change Check the Cylinder Compression to ON and crank the engine.
      3. Use a fully-charged battery.

    11. Stop cranking the engine, and then change "Check the Cylinder Compression" to OFF after the engine stops.

      NOTICE:
      If the Active Test is changed to OFF while the engine is being cranked, the engine will start.

    12. Push the snapshot button to turn the snapshot function off.
    13. Select "Stored Data" on the Techstream screen, select the recorded data and display the data as a graph.

      HINT:
      If the data is not displayed as a graph, the change of the values cannot be observed.

    14. Check the change in engine speed values.

      HINT:
      As the data values of the Active Test return to their default values when cranking is stopped, the engine speed value of each cylinder cannot be observed. Therefore, it is necessary to use the data recorded with the snapshot function to check the engine speed values recorded during cranking.


SYSTEM CHECK

HINT:
Performing a System Check enables the system, which consists of multiple actuators, to be operated without removing any parts. In addition, it can show whether or not any DTCs are stored, and can detect potential malfunctions in the system. The System Check can be performed with the Techstream.

  1. Connect the Techstream to the DLC3.

  2. Turn the ignition switch to ON.

  3. Turn the Techstream on.

  4. Enter the following menus: Powertrain / Engine and ECT / Utility.

  5. Perform the System Check by referring to the table below.

    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Evaporative System Check
    (Automatic Mode)
    Perform 6 steps in order to operate EVAP key-off monitor automatically
    35°C (95°F) or less
    1. If no DTCs in Pending menu after performing this test, system functioning normally.
    2. Refer to EVAP Inspection Procedure (Click here).
    Evaporative System Check
    (Manual Mode)
    Perform 6 steps in order to operate EVAP key-off monitor manually
    35°C (95°F) or less
    1. Used to detect malfunctioning parts.
    2. Refer to EVAP Inspection Procedure (Click here).
    Secondary Air Injection Check
    (Automatic Mode)
    Perform secondary air injection system operation automatically
    With warm engine, ignition switch turned off once
    1. If no DTCs in Pending menu after performing this test, system functioning normally.
    2. Refer to inspection procedure for secondary air injection system DTCs.
    3. When performing Secondary Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running.
    4. Turn ignition switch off when System Check finished.
    Secondary Air Injection Check
    (Manual Mode)
    Perform 7 operations in order to operate air injection system monitor manually
    With warm engine, ignition switch turned off once
    1. Used to detect malfunctioning parts.
    2. Refer to inspection procedure for secondary air injection system DTCs.
    3. When performing Secondary Air Injection Check operation after battery cable has been reconnected, wait for 7 minutes with ignition switch turned to ON or engine running.
    4. Turn ignition switch off when System Check finishes.