CYLINDER HEAD > REPLACEMENT |
| 1. REPLACE INTAKE VALVE GUIDE BUSH |
Heat the cylinder head to 80 to 100°C (176 to 212°F).
Place the cylinder head on wooden blocks.
![]() |
Using SST and a hammer, tap out the intake valve guide bushes.
Using a caliper gauge, measure the intake valve guide bush bore diameter of the cylinder head.
| Item | Specified Condition |
| STD | 10.285 to 10.306 mm (0.4049 to 0.4057 in.) |
| O/S 0.05 | 10.335 to 10.356 mm (0.4069 to 0.4077 in.) |
Select a new valve guide bush.
| Item | Specified Condition | |
| Bush Bore Diameter | 10.285 to 10.306 mm (0.4049 to 0.4057 in.) | 10.335 to 10.356 mm (0.4069 to 0.4077 in.) |
| Use Bush | STD | O/S 0.05 |
| Item | Specified Condition |
| STD | 10.333 to 10.344 mm (0.4068 to 0.4072 in.) |
| O/S 0.05 | 10.383 to 10.394 mm (0.4088 to 0.4092 in.) |
Heat the cylinder head to 80 to 100°C (176 to 212°F).
Place the cylinder head on wooden blocks.
![]() |
Using SST, tap in the intake valve guide bushes to the specified protrusion height.
| *1 | Protrusion Height |
![]() |
Using a sharp 5.5 mm reamer, ream the valve guide bushes to obtain the specified clearance.
| 2. REPLACE EXHAUST VALVE GUIDE BUSH |
Heat the cylinder head to 80 to 100°C (176 to 212°F).
Place the cylinder head on wooden blocks.
![]() |
Using SST and a hammer, tap out the exhaust valve guide bushes.
Using a caliper gauge, measure the exhaust valve guide bush bore diameter of the cylinder head.
| Item | Specified Condition |
| STD | 10.285 to 10.306 mm (0.4049 to 0.4057 in.) |
| O/S 0.05 | 10.335 to 10.356 mm (0.4069 to 0.4077 in.) |
Select a new valve guide bush.
| Item | Specified Condition | |
| Bush Bore Diameter | 10.285 to 10.306 mm (0.4049 to 0.4057 in.) | 10.335 to 10.356 mm (0.4069 to 0.4077 in.) |
| Use Bush | STD | O/S 0.05 |
| Item | Specified Condition |
| STD | 10.333 to 10.344 mm (0.4068 to 0.4072 in.) |
| O/S 0.05 | 10.383 to 10.394 mm (0.4088 to 0.4092 in.) |
Heat the cylinder head to 80 to 100°C (176 to 212°F).
Place the cylinder head on wooden blocks.
![]() |
Using SST, tap in the exhaust valve guide bushes to the specified protrusion height.
| *1 | Protrusion Height |
![]() |
Using a sharp 5.5 mm reamer, ream the valve guide bushes to obtain the specified clearance.
| 3. REPLACE STRAIGHT PIN |
Using a plastic-faced hammer, tap in new straight pins as shown in the illustration.

| *A | RH | *B | LH |
| *1 | Protrusion Height | - | - |
| 4. REPLACE RING PIN |
![]() |
Using a plastic-faced hammer, tap in new ring pins to the specified protrusion height.
| *A | RH |
| *B | LH |
| *1 | Protrusion Height |
| 5. REPLACE SPARK PLUG TUBE |
![]() |
Apply adhesive to the end of a new spark plug tube.
| *1 | Adhesive |
| *2 | Distance |
![]() |
Using a wooden block and hammer, tap in the spark plug tube to the specified protrusion height.
| *1 | Cylinder Head Top Surface |
| *2 | Protrusion Height |