DTC P0617 Starter Relay Circuit High |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0617 | When conditions (a), (b) and (c) met, positive (+B) battery voltage 10.5 V or more applied to ECM for 20 seconds (1 trip detection logic)
|
|
| Related DTCs | P0617: Starter signal |
| Required Sensors/Components (Main) | ST relay, PNP switch and Ignition switch |
| Required Sensors/Components (Related) | Vehicle Speed Sensor (VSS), Crankshaft Position (CKP) sensor |
| Frequency of Operation | Continuous |
| Duration | 20 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not stored | None |
| Battery voltage | 10.5 V or more |
| Vehicle speed | 20 km/h (12.43 mph) or more |
| Engine speed | 1000 rpm or more |
| Starter signal | ON |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
| ON | Close |
| START | Open |
|
| ||||
| OK | ||
| ||
| 2.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Disconnect the D35 PNP switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 4 (B) - 5 (L) | Shift lever position P | Below 1 Ω |
| Shift lever position N | Below 1 Ω | |
| Shift lever position not on P or N | 10 kΩ or higher | |
| 2 (RB) - 5 (L) | All positions | 10 kΩ or higher |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 3.REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
Replace the park / neutral position switch (Click here).
| NEXT | |
| 4.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
| ON | Close |
| START | Open |
|
| ||||
| OK | ||
| ||
| 5.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the J9 ignition switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 5 (AM2) - 7 (ST2) | Ignition switch position LOCK | 10 kΩ or higher |
| Ignition switch position START | Below 1 Ω |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 6.REPLACE IGNITION SWITCH ASSEMBLY |
Replace the ignition switch (Click here).
| NEXT | |
| 7.READ VALUE USING TECHSTREAM (STARTER SIGNAL) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Starter Signal.
Check the value displayed on the Techstream when the ignition switch is turned to the ON and START positions.
| Ignition Switch Position | Starter Signal |
| ON | Close |
| START | Open |
|
| ||||
| OK | ||
| ||
| 8.REPAIR OR REPLACE HARNESS OR CONNECTOR (PNP SWITCH - STA TERMINAL OF ECM) |
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P0617 is output | A |
| No DTC is output | B |
|
| ||||
| A | ||
| ||