DTC P0420 Catalyst System Efficiency Below Threshold (Bank 1) |
DTC P0430 Catalyst System Efficiency Below Threshold (Bank 2) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0420 | OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic) |
|
| P0430 | OSC value smaller than standard value under active air-fuel ratio control (2 trip detection logic) |
|


| Related DTCs | P0420: Catalyst Deterioration (for Bank 1) P0430: Catalyst Deterioration (for Bank 2) |
| Required Sensors/Components (Main) | A/F sensor and HO2 sensor |
| Required Sensors/Components (Related) | Intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor |
| Frequency of Operation | Once per driving cycle |
| Duration | About 30 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (VVT Oil control valve) P0011, P0021 (VVT System - Advance) P0012, P0022 (VVT System - Retard) P0013, P0023 (Exhaust VVT Oil control valve) P0014, P0024 (Exhaust VVT System - Advance) P0015, P0025 (Exhaust VVT System - Retard) P0016, P0018 (VVT System - Misalignment) P0017, P0019 (Exhaust VVT System - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P0037, P0038, P0057, P0058, P102D, P105D (Rear oxygen sensor heater) P0102, P0103 (Mass air flow meter) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P0136, P0137, P0138, P0139, P0156, P0157, P0158, P0159, P0607 (Rear oxygen sensor) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0308 (Misfire) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0358 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0412, P0415, P0418, P0419, P1613, P1614 (Secondary air injection system control) P2440 - P2447 (Secondary air injection system) P0500 (Vehicle speed sensor) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Air fuel ratio sensor) P1340 (Camshaft position sensor) |
| Battery voltage | 11 V or more |
| Intake air temperature | -10°C (14°F) or more |
| Engine coolant temperature | 75°C (167°F) or more |
| Atmospheric pressure | 76 kPa (570 mmHg) or more |
| Idling | OFF |
| Engine RPM | Less than 3200 rpm |
| A/F sensor status | Activated |
| Fuel system status | Closed loop |
| Engine load | 10 to 75% |
| All of following conditions (a), (b) and (c) met | - |
| (a) Mass air flow rate | 7.5 to 75 gm/s |
| (b) Estimated front catalyst temperature | 575 to 820°C (1067 to 1508°F) |
| (c) Estimated rear catalyst temperature | 400 to 700°C (752 to 1292°F) |
| Shift position | 4th or higher |
| Oxygen Storage Capacity (OSC) of Three-Way Catalytic Converter (TWC) | Less than 0.12 g |



| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 or AFS Voltage B2S1 (A/F) | +12.5% | Rich | Less than 3.1 V |
| AFS Voltage B1S1 or AFS Voltage B2S1 (A/F) | -12.5% | Lean | More than 3.4 V |
| O2S B1S2 or O2S B2S2 (HO2) | +12.5% | Rich | More than 0.55 V |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5% | Lean | Less than 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area |
| 1 | ![]() ![]() | ![]() ![]() | - |
| 2 | ![]() ![]() | ![]() ![]() |
|
| 3 | ![]() ![]() | ![]() ![]() |
|
| 4 | ![]() ![]() | ![]() ![]() |
|
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 OR P0430) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0420 or P0430 is output | A |
| DTC P0420 or P0430 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME) |
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Warm up the engine and run the engine at an engine speed of 2500 rpm for approximately 90 seconds.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume.
Perform the Control the Injection Volume operation with the engine idling.
Monitor the voltage outputs of the air fuel ratio and heated oxygen sensors (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.
| Techstream Display (Sensor) | Injection Volume | Status | Voltage |
| AFS Voltage B1S1 or AFS Voltage B2S1 (Air fuel ratio) | +12.5% | Rich | Below 3.1 V |
| -12.5% | Lean | Higher than 3.4 V | |
| O2S B1S2 or O2S B2S2 (Heated oxygen) | +12.5% | Rich | Higher than 0.55 V |
| -12.5% | Lean | Below 0.4 V |
| Status of AFS Voltage B1S1 or AFS Voltage B2S1 | Status of O2S B1S2 or O2S B2S2 | Air Fuel Ratio Condition and Air Fuel Ratio and Heated Oxygen Sensor Condition | Suspected Trouble Area | Proceed to |
| Lean/Rich | Lean/Rich | Normal |
| A |
| Lean | Lean/Rich | Air fuel ratio sensor malfunction | Air fuel ratio sensor | B |
| Rich | Lean/Rich | Air fuel ratio sensor malfunction | Air fuel ratio sensor | B |
| Lean/Rich | Lean | Heated oxygen sensor malfunction |
| C |
| Lean/Rich | Rich | Heated oxygen sensor malfunction |
| C |
| Lean | Lean | Actual air fuel ratio lean |
| D |
| Rich | Rich | Actual air fuel ratio rich |
| D |
Refer to "Data List / Active Test" [AFS Voltage B1S1, AFS Voltage B2S1, O2S B1S2 and O2S B2S2] (Click here).
|
| ||||
|
| ||||
|
| ||||
| A | |
| 3.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks from the exhaust manifold sub-assembly and exhaust pipes.
|
| ||||
| OK | |
| 4.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430) |
According to the output DTCs in the step 1 (Check Any Other DTCs Output), proceed to next step referring to the table below.
| Result | Proceed to |
| P0420 (for Regular Cab Standard Deck) is output | A |
| P0420 (except Regular Cab Standard Deck) is output | B |
| P0430 (for Regular Cab Standard Deck) is output | C |
| P0430 (except Regular Cab Standard Deck) is output | D |
| P0420 and P0430 (for Regular Cab Standard Deck) are output | A and C |
| P0420 and P0430 (except Regular Cab Standard Deck) are output | B and D |
|
| ||||
|
| ||||
|
| ||||
| A | ||
| ||
| 5.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks from the exhaust manifold assembly and exhaust pipes.
|
| ||||
| OK | ||
| ||
| 6.CHECK FOR EXHAUST GAS LEAK |
Check for exhaust gas leaks from the exhaust manifold assembly and exhaust pipes.
|
| ||||
| OK | ||
| ||