AUTOMATIC TRANSMISSION SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List.
According to the display on the Techstream, read the Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| N Range Status | Shift lever N status/ ON or OFF |
| - |
| Neutral Position SW Signal | PNP switch status/ ON or OFF |
| When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Stop Light Switch | Stop light switch status/ ON or OFF | Brake pedal is:
| - |
| SPD (NT) | Input shaft speed/ Min.: 0 rpm Max.: 12750 rpm | Lock-up is:
| Data is displayed in increments of 50 rpm |
| SPD (SP2) | Output shaft speed/ Min.: 0 km/h (0 mph) Max.: 255 km/h (158 mph) | Vehicle stopped: 0 km/h (0 mph) (output shaft speed is equal to vehicle speed) | - |
| Shift SW Status (P Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (R Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (N Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| Shift SW Status (N, P Range) Supported | Status of PNP switch (N or P) supported/ Supp or Unsupp | - | - |
| Shift SW Status (N, P Range) | PNP switch status/ ON or OFF |
| - |
| Sports Shift Up SW | Sport shift up switch status/ ON or OFF |
| - |
| Sports Shift Down SW | Sport shift down switch status/ ON or OFF |
| - |
| Sports Mode Selection SW | Sport mode select switch status/ ON or OFF |
| - |
| Shift SW Status (D Range) | PNP switch status/ ON or OFF |
| When shift lever position displayed on Techstream differs from actual position, adjustment of PNP switch or shift cable may be incorrect
|
| A/T Oil Temperature 1 | No. 1 ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If value is -40°C (-40°F) or 215°C (419°F), No. 1 ATF temperature sensor circuit is open or shorted |
| A/T Oil Temperature 2 | No. 2 ATF temperature sensor value/ Min.: -40°C (-40°F) Max.: 215°C (419°F) |
| If value is -40°C (-40°F) or 215°C (419°F), No. 2 ATF temperature sensor circuit is open or shorted |
| Lock Up | Lock-up/ ON or OFF | Lock-up is:
| - |
| Shift Status | ECM gear shift command/ 1st, 2nd, 3rd, 4th, 5th or 6th |
| - |
| SLT Solenoid Status | Shift solenoid SLT status/ ON or OFF |
| - |
| SLU Solenoid Status | Shift solenoid SLU status/ ON or OFF | Shift solenoid SLU is:
| - |
| AT Fluid | Flex lock-up judder judgment/ ON or OFF |
| - |
| PERFORM ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLU) | Operate shift solenoid SLU | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (SLT)* | Operate shift solenoid SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
| Activate the Solenoid (S1) | Operate shift solenoid S1 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (S2) | Operate shift solenoid S2 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (S3) | Operate shift solenoid S3 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (S4) | Operate shift solenoid S4 | ON or OFF | [Vehicle Condition]
|
| Activate the Lock Up | Control shift solenoid SLU to set automatic transmission to lock-up condition | ON or OFF | Possible to check shift solenoid valve SLU operation [Vehicle Condition]
|
| Control the Shift Position | Operate shift solenoid valve and set each shift position |
| Possible to check operation of shift solenoid valves [Vehicle Condition] 50 km/h (30 mph) or less |
| Activate the Solenoid (SR) | Operate shift solenoid SR | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (SL1) | Operate shift solenoid SL1 | ON or OFF | [Vehicle Condition]
|
| Activate the Solenoid (SL2) | Operate shift solenoid SL2 | ON or OFF | [Vehicle Condition]
|