Home › ENGINE · 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0724    Brake Switch "B" Circuit High

for Preparation Click here


DESCRIPTION

The purpose of this circuit is to prevent the engine from stalling while driving in the lock-up condition when the brakes are suddenly applied.
When the brake pedal is depressed, this switch sends a signal to the ECM. Then the ECM cancels the operation of the lock-up clutch while braking is in progress.

DTC Code
DTC Detection Condition
Trouble Area
P0724
Stop light switch remains ON even when vehicle is driven in GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) pattern 5 times (2 trip detection logic)
  1. Short in stop light switch signal circuit
  2. Stop light switch
  3. ECM

MONITOR DESCRIPTION

This DTC indicates that the stop light switch remains ON. When the stop light switch remains ON during GO and STOP driving, the ECM interprets this as a fault in the stop light switch. Then the MIL illuminates and the ECM stores the DTC. The vehicle must GO (30 km/h (18.65 mph) or more) and STOP (less than 3 km/h (1.86 mph)) 5 times for 2 driving cycles in order for the DTC to be output.

MONITOR STRATEGY


Related DTCs
P0724: Stop light switch/Range check/Rationality
Required sensors/Components
Stop light switch, Vehicle speed sensor
Frequency of operation
Continuous
Duration
GO and STOP 5 times
MIL operation
2 driving cycles
Sequence of operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever this DTC is not present.
None
Battery voltage
8 V or more
Starter
OFF
Ignition switch
ON
GO: Vehicle speed
30 km/h (18.65 mph) or more
STOP: Vehicle speed
Less than 3 km/h (1.86 mph)

TYPICAL MALFUNCTION THRESHOLDS


Brake switch
Stuck ON

CONFIRMATION DRIVING PATTERN


A199312E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Wait 5 seconds.
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [B].
  8. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P0724.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or N/A, perform steps [C] through [E].

  12. Start the engine [C].
  13. Accelerate the vehicle to 30 km/h (18.65 mph) or more, depress the brake pedal and decelerate the vehicle to 3 km/h (1.86 mph) or less [D]. Repeat step [D] 5 times.
  14. Check the DTC judgment result [E].
  15. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A164732E01


INSPECTION PROCEDURE

HINT:
Using the Techstream to read the Data List allows switch, sensor, actuator and other item values to be read without removing any parts. Reading the Data List early in troubleshooting is one way to save time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.
  2. Turn the ignition switch off.
  3. Connect the Techstream to the DLC3.
  4. Turn the ignition switch to ON.
  5. Turn the Techstream on.
  6. Enter the following menus: Powertrain / Engine and ECT / Data List.
  7. Follow the instructions on the Techstream and read the Data List.

Item
Measurement Item/
Range (Display)
Normal Condition
Diagnostic Note
Stop Light Switch
Stop light switch status/
ON or OFF
  1. Brake pedal is depressed: ON
  2. Brake pedal is released: OFF
-
1.INSPECT STOP LIGHT SWITCH
A115657E13
  1. Remove the stop light switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin not pushed
    Below 1 Ω
    Pin pushed
    10 kΩ or higher
    3 - 4
    Pin not pushed
    10 kΩ or higher
    Pin pushed
    Below 1 Ω



NG
REPLACE STOP LIGHT SWITCH (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (ECM - BATTERY)
  1. Disconnect the A24 ECM connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:

    Tester Connection
    Condition
    Specified Condition
    A24-36 (STP) - Body ground
    Brake pedal is depressed
    11 to 14 V
    A24-36 (STP) - Body ground
    Brake pedal is released
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)