DTC P0729 Gear 6 Incorrect Ratio |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0729 |
(b) When the ECM directs the transmission to switch to 6th gear, the actual gear is shifted to 4th. |
|
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Actual gear position under malfunction | 1st | 2nd | 3rd | 4th | 5th | 4th |
| Gear position under normal conditions | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Actual gear position under fail-safe mode | 1st | 2nd | 3rd | 3rd | 3rd | 3rd |
| Related DTCs | P0729: Gear 6 incorrect ratio (Sequence valve) / Functional check |
| Required sensors/Components | Sequence valve |
| Frequency of operation | Continuous |
| Duration | 0.4 seconds |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0500 (Output speed sensor circuit) P0327, P0328, P0332, P0333 (KCS sensor circuit) |
| Shift solenoid valve S1 circuit | Not circuit malfunction |
| Shift solenoid valve S2 circuit | Not circuit malfunction |
| Shift solenoid valve S3 circuit | Not circuit malfunction |
| Shift solenoid valve S4 circuit | Not circuit malfunction |
| Shift solenoid valve SR circuit | Not circuit malfunction |
| Shift solenoid valve SL1 circuit | Not circuit malfunction |
| Shift solenoid valve SL2 circuit | Not circuit malfunction |
| ECT (Engine Coolant Temperature) sensor circuit | Not circuit malfunction |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or more |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| Transfer position | HIGH* |
| Vehicle speed sensor "A" circuit | Not circuit malfunction |
| Output shaft speed sensor circuit | Not circuit malfunction |
| Transfer output speed | 143 rpm or more |
| Transfer input speed / Transfer output speed (NO / NOtf) | 0.9 or more, and less than 1.1 |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 6.6% or more at 2000 rpm (Conditions vary with engine speed) |
| ECM selected gear | 6th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 6.6% or more at 2000 rpm (Conditions vary with engine speed) |
| Turbine speed / Output speed (NT / NO) | 0.65 or more, and 0.79 or less (This means actual gear is 5th) |
| Turbine speed / Output speed (NT / NO) | 0.93 or more, and 1.07 or less (This means actual gear is 4th) |
| 1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0729) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P0729 is output | A |
| P0729 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (RUNNING TEST) |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valves and set each shift position |
| Possible to check operation of the shift solenoid valves. [Vehicle Condition] 50 km/h (30 mph) or less |
| Tester gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Actual gear position under malfunction | 1st | 2nd | 3rd | 4th | 5th | 4th |
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT) |
![]() |
Remove the test plug from the center of the right side of the transmission case and connect SST.
Connect the Techstream to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
Measure the line pressure.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | Operate the shift solenoid SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
| *1 | Test Plug |
|
| ||||
| OK | |
| 4.CLEAR DTC AND PERFORM RUNNING TEST |
Clear the DTC (Click here).
Check for the DTC again after conducting the Monitor Drive Pattern (Click here).
|
| ||||
| OK | ||
| ||