DTC P0751 Shift Solenoid "A" Performance (Shift Solenoid Valve S1) |
| DTC Code | DTC Detection Condition | Trouble Area |
| P0751 |
(b) When the ECM directs the transmission to switch to 5th gear, the actual gear is shifted to 5th. |
|
| P0751 |
(b) When the ECM directs the transmission to switch to 6th gear, the engine overruns (clutch slips). |
|
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| *1: Actual gear position under S1 stuck ON malfunction | 2nd | 2nd | 3rd | 4th | 5th | 6th |
| *2: Actual gear position under S1 stuck OFF malfunction | 1st | 1st | 3rd | 4th | 5th | N* |
| Gear position under normal conditions | 1st | 2nd | 3rd | 4th | 5th | 6th |
| *1: Actual gear position under fail-safe mode during S1 stuck ON malfunction | 2nd | 2nd | 3rd | 4th | 5th | 6th |
| *2: Actual gear position under fail-safe mode during S1 stuck OFF malfunction | 1st*3 | 1st*3 | 3rd | 3rd | 3rd | 3rd |
| Related DTCs | P0751: Shift solenoid valve S1/Functional check |
| Required sensors/Components | Shift solenoid valve S1, Speed sensor (NT), Speed sensor (SP2), Crankshaft position sensor (NE), Throttle position sensor, MAF |
| Frequency of operation | Continuous |
| Duration | OFF malfunction (A) and ON malfunction (A), (B) 0.4 seconds OFF malfunction (B) 3 seconds OFF malfunction (C) 1 second |
| MIL operation | 2 driving cycles |
| Sequence of operation | None |
| The monitor will run whenever the following DTCs are not present | P0717 (Turbine speed sensor circuit) P0500 (Output speed sensor circuit) P0327, P0328, P0332, P0333 (KCS sensor circuit) |
| Shift solenoid valve S1 circuit | Not circuit malfunction |
| Shift solenoid valve S2 circuit | Not circuit malfunction |
| Shift solenoid valve S3 circuit | Not circuit malfunction |
| Shift solenoid valve S4 circuit | Not circuit malfunction |
| Shift solenoid valve SR circuit | Not circuit malfunction |
| Shift solenoid valve SL1 circuit | Not circuit malfunction |
| Shift solenoid valve SL2 circuit | Not circuit malfunction |
| ECT (Engine Coolant Temperature) sensor circuit | Not circuit malfunction |
| ETCS (Electric Throttle Control System) | Not system down |
| Transmission position | "D" |
| Duration time from shifting "N" to "D" | 4 seconds or more |
| ECT | 40°C (104°F) or more |
| Spark advance from max. retard timing by KCS control | 0° crankshaft angle or more |
| Engine | Starting |
| Transfer position | HIGH* |
| Vehicle speed sensor "A" circuit | Not circuit malfunction |
| Output shaft speed sensor circuit | Not circuit malfunction |
| Transfer output speed | 143 rpm or more |
| Transfer input speed / Transfer output speed (NO / NOtf) | 0.9 or more, and less than 1.1 |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 6.6% or more at 2000 rpm (Conditions vary with engine speed) |
| Current ECM selected gear | 6th |
| Last ECM selected gear | 5th |
| Vehicle speed (During transition from 5th to 6th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 6th |
| Engine speed - Turbine speed (NE - NT) (After transition from 5th to 6th gear) | 150 rpm or less |
| Vehicle speed (After transition from 5th to 6th gear) | Less than 100 km/h (62.2 mph) |
| ECM selected gear | 1st |
| Vehicle speed | 2 km/h (1.2 mph) or more and less than 40 km/h (24.9 mph) |
| Engine speed - Turbine speed (NE - NT) | 50 rpm or more |
| ECM selected gear | 5th |
| Vehicle speed | 2 km/h (1.2 mph) or more |
| Throttle valve opening angle | 6.6% or more at 2000 rpm (Conditions vary with engine speed) |
| Turbine speed / Output speed (NT / NO) | 0.65 or more, and 0.79 or less (This means actual gear is 5th) |
| Turbine speed - Output speed x 5th gear ratio (NT - NO x 5th gear ratio) | 1000 rpm or more |
| Turbine speed - Output speed x 6th gear ratio (NT - NO x 6th gear ratio) | 1000 rpm or more |
| Turbine speed / Output speed (NT / NO) | 1.91 or more, and 2.35 or less (This means actual gear is 2nd) |
| Turbine speed / Output speed (NT / NO) | 0.65 or more, and 0.79 or less (This means actual gear is 5th) |
| ACTIVE TEST |
Warm up the engine.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Control the Shift Position | Operate shift solenoid valves and set each shift position |
| Possible to check operation of the shift solenoid valves. [Vehicle Condition] 50 km/h (30 mph) or less |
| ECM gear shift command | 1st | 2nd | 3rd | 4th | 5th | 6th |
| Shift solenoid valve S1 | OFF | ON | ON | ON | ON | ON |
| 1.CHECK DTC OUTPUT (IN ADDITION TO DTC P0751) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs using the Techstream.
| Result | Proceed to |
| Only P0751 is output | A |
| P0751 and other DTCs are output | B |
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (SHIFT SOLENOID VALVE SLT) |
![]() |
Remove the test plug from the center of the right side of the transmission case and connect SST.
Connect the Techstream to the DLC3.
Start the engine and warm it up.
Measure the line pressure with SST.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Active Test.
According to the display on the Techstream, perform the Active Test.
Measure the line pressure.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Activate the Solenoid (SLT)* | Operate the shift solenoid SLT and raise line pressure | ON or OFF
| [Vehicle Condition]
|
| *1 | Test Plug |
|
| ||||
| OK | |
| 3.INSPECT SHIFT SOLENOID VALVE S1 |
![]() |
Remove shift solenoid valve S1.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Shift solenoid valve S1 connector terminal - Shift solenoid valve S1 body | 20°C (68°F) | 11 to 15 Ω |
Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.
| Measurement Condition | Specified Condition |
| Valve moves and makes an operating noise |
| *a | Component without harness connected (Shift Solenoid Valve S1) |
|
| ||||
| OK | |
| 4.INSPECT TRANSMISSION VALVE BODY ASSEMBLY |
Check the transmission valve body assembly.
|
| ||||
| OK | ||
| ||