DTC P0340 Camshaft Position Sensor Circuit Malfunction |
DTC P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor) |
DTC P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor) |
DTC P0345 Camshaft Position Sensor "A" Circuit (Bank 2) |
DTC P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2) |
DTC P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0340 P0345 | No VVT sensor signal to ECM at engine speed of 600 rpm or more (1 trip detection logic) |
|
| P0342 P0347 | Output voltage of VVT sensor less than 0.3 V for 4 seconds (1 trip detection logic) |
|
| P0343 P0348 | Output voltage of VVT sensor more than 4.7 V for 4 seconds (1 trip detection logic) |
|
![]() |
| Tester Connection | Tool Setting | Condition | Specified Condition |
| D74-110 (NE+) - D74-111 (NE-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D74-92 (VV1+) - D74-91 (VV1-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D74-87 (VV2+) - D74-88 (VV2-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| Related DTCs | P0340: VVT position sensor (for Bank 1) verify pulse input P0342: VVT position sensor (for Bank 1) range check (low voltage) P0343: VVT position sensor (for Bank 1) range check (high voltage) P0345: VVT position sensor verify pulse input (for Bank 2) P0347: VVT position sensor (for Bank 2) range check (low voltage) P0348: VVT position sensor (for Bank 2) range check (high voltage) |
| Required Sensors/Components (Main) | VVT position sensor (for Bank 1 and 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | P0340, P0345: 5 seconds P0342, P0343, P0347, P0348: 4 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not present | P0342, P0343, P0347, P0348 (VVT sensor) |
| Engine speed | 600 rpm or more |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Ignition switch | ON |
| Monitor runs whenever following DTCs are not present | P0340, P0345 (VVT sensor) |
| Starter | OFF |
| Ignition switch ON and time after ignition switch is off to ON | 2 seconds or more |
| Battery voltage | 8 V or more |
| VVT sensor signal | No signal |
| VVT sensor voltage | Less than 0.3 V |
| VVT sensor voltage | More than 4.7 V |
| VVT sensor signal | No signal |
| VVT sensor voltage | Less than 0.3 V |
| VVT sensor voltage | More than 4.7 V |
| VVT sensor voltage | 0.3 to 4.7 V |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the VVT sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (VC) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM) |
![]() |
Disconnect the VVT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D37-1 (VVL+) - D74-92 (VV1+) | Always | Below 1 Ω |
| D37-2 (VVL-) - D74-91 (VV1-) | Always | Below 1 Ω |
| D39-1 (VVR+) - D74-87 (VV2+) | Always | Below 1 Ω |
| D39-2 (VVR-) - D74-88 (VV2-) | Always | Below 1 Ω |
| D37-1 (VVL+) or D74-92 (VV1+) - Body ground | Always | 10 kΩ or higher |
| D37-2 (VVL-) or D74-91 (VV1-) - Body ground | Always | 10 kΩ or higher |
| D39-1 (VVR+) or D74-87 (VV2+) - Body ground | Always | 10 kΩ or higher |
| D39-2 (VVR-) or D74-88 (VV2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT) |
![]() |
Check the VVT sensor installation.
|
| ||||
| OK | |
| 4.INSPECT INTAKE CAMSHAFT (TEETH) |
Check the teeth of the camshaft.
|
| ||||
| OK | |
| 5.REPLACE VVT SENSOR |
Replace the VVT sensor (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs.
Refer to the confirmation driving pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read DTCs.
| Result | Proceed to |
| No DTC is output | A |
| P0340, P0342, P0343, P0345, P0347 or P0348 is output | B |
|
| ||||
| A | ||
| ||