DTC P0365 Camshaft Position Sensor "B" Circuit (Bank 1) |
DTC P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1) |
DTC P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1) |
DTC P0390 Camshaft Position Sensor "B" Circuit (Bank 2) |
DTC P0392 Camshaft Position Sensor "B" Circuit Low Input (Bank 2) |
DTC P0393 Camshaft Position Sensor "B" Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0365 P0390 | No VVT sensor signal to ECM during engine running (1 trip detection logic) |
|
| P0367 P0392 | Output voltage of VVT sensor less than 0.3 V 4 seconds (1 trip detection logic) |
|
| P0368 P0393 | Output voltage of VVT sensor more than 4.7 V 4 seconds (1 trip detection logic) |
|
![]() |
| Tester Connection | Tool Setting | Condition | Specified Condition |
| D74-110 (NE+) - D74-111 (NE-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D74-69 (EV1+) - D74-68 (EV1-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| D74-64 (EV2+) - D74-65 (EV2-) | 5 V/DIV. 20 msec./DIV. | Cranking or idling | The correct waveform is as shown |
| Related DTCs | P0365: VVT sensor (for Bank 1) verify pulse input P0367: VVT position sensor (for Bank 1) range check (low voltage) P0368: VVT position sensor (for Bank 1) range check (high voltage) P0390: VVT sensor (for Bank 2) verify pulse input P0392: VVT position sensor (for Bank 2) range check (low voltage) P0393: VVT position sensor (for Bank 2) range check (high voltage) |
| Required Sensors/Components (Main) | VVT position sensor (for Bank 1 and 2) |
| Required Sensors/Components (Related) | Crankshaft position sensor |
| Frequency of Operation | Continuous |
| Duration | 5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not stored | None |
| Exhaust VVT sensor voltage | 0.3 to 4.7 V |
| Engine speed | 600 rpm or more |
| Battery voltage | 8 V or more |
| Starter | OFF |
| Ignition switch | ON |
| Exhaust camshaft position sensor range check failure (P0367, P0368, P0392, P0393) | Not detected |
| Monitor runs whenever following DTCs are not stored | None |
| Starter | OFF |
| Ignition switch | ON |
| Time after ignition switch off to ON | 2 seconds or more |
| Battery voltage | 8 V or more |
| Exhaust camshaft position sensor verify pulse input failure (P0365, P0390) | Not detected |
| Exhaust VVT sensor signal | No signal |
| Exhaust VVT sensor voltage | Less than 0.3 V |
| Exhaust VVT sensor voltage | More than 4.7 V |
| VVT sensor voltage | 0.3 to 4.7 V |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the D40 or D41 VVT sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 3 (VC2) - Body ground | Ignition switch ON | 4.5 to 5.0 V |
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM) |
Disconnect the D40 or D41 VVT sensor connector.
Disconnect the D74 ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D40-1 (EX+) - D74-69 (EV1+) | Always | Below 1 Ω |
| D40-2 (EX-) - D74-68 (EV1-) | Always | Below 1 Ω |
| D41-1 (EX+) - D74-64 (EV2+) | Always | Below 1 Ω |
| D41-2 (EX-) - D74-65 (EV2-) | Always | Below 1 Ω |
| D40-1 (EX+) or D74-69 (EV1+) - Body ground | Always | 10 kΩ or higher |
| D40-2 (EX-) or D74-68 (EV1-) - Body ground | Always | 10 kΩ or higher |
| D41-1 (EX+) or D74-64 (EV2+) - Body ground | Always | 10 kΩ or higher |
| D41-2 (EX-) or D74-65 (EV2-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT) |
![]() |
Check the VVT sensor installation.
|
| ||||
| OK | |
| 4.CHECK EXHAUST CAMSHAFT |
Check the teeth of the camshaft.
|
| ||||
| OK | |
| 5.REPLACE VVT SENSOR (FOR EXHAUST SIDE) |
Replace the VVT sensor (for exhaust side) (Click here).
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (Click here).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0365, P0367, P0368, P0390, P0392 or P0393 | B |
|
| ||||
| A | ||
| ||