Home › ENGINE ยท 3UR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P011B    Engine Coolant Temperature / Intake Air Temperature Correlation

for Preparation Click here


DESCRIPTION

The engine has two temperature sensors, an Engine Coolant Temperature (ECT) sensor and an Intake Air Temperature (IAT) sensor, to detect the temperature while the engine is in operation. A thermistor, whose resistance value varies according to the temperature, is built into each sensor. When the temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes. Based on these temperature signals output from the sensors, the ECM determines the fuel injection time and the ignition timing to control the engine.

DTC Code
DTC Detection Condition
Trouble Area
P011B
  1. All of the following conditions are met (2 trip detection logic):
    1. The battery voltage is 10.5 V or higher.
    2. 7 hours or more have elapsed from engine stop on the previous trip.
    3. 15 seconds after a cold engine start.
    4. The minimum Intake Air Temperature (IAT) after the engine starts is higher than -10°C (14°F).
    5. The average Engine Coolant Temperature (ECT) before the engine starts is higher than -10°C (14°F).
    6. The difference between the readings of ECT and IAT is higher than 20°C (36°F).
  1. IAT sensor
  2. ECT sensor
  3. ECM

A163149E46

HINT:
  1. Waiting is required to prevent the temperature of the engine from affecting the readings. If the engine has been operated recently, it will not be possible to accurately compare the readings.
  1. For diagnosis, in order to duplicate the detection conditions of the DTC, it is necessary to park the vehicle for 7 hours. Parking the vehicle for 7 hours ensures that the actual temperature of the ECT and IAT are very similar. When the vehicle has been parked for less than 7 hours, differences in the readings may exist, this does not necessarily indicate a fault.


MONITOR DESCRIPTION

The ECM monitors the difference between the Engine Coolant Temperature (ECT) and the Intake Air Temperature (IAT) when the engine is started cold to detect the engine temperature conditions accurately. The monitor runs when the engine started cold after 7 hours or more have elapsed since the engine was stopped (ignition switch turned off) on the previous trip. If the difference between the ECT and the IAT on a cold start exceeds 20°C (36°F), the ECM interprets this as a malfunction in the ECT sensor circuit and IAT sensor circuit, and stores the DTC.

MONITOR STRATEGY


Related DTCs
P011B: Engine Coolant Temperature (ECT) / Intake Air Temperature (IAT) sensor correlation
Required Sensors/Components (Main)
ECT / IAT sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
-
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


The monitor will run whenever these DTCs are not stored
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0125 (Insufficient coolant temperature for closed loop fuel control)
P2610 (ECM internal engine off timer)
All of following conditions met
Conditions 1 and 2
1. All of following conditions met
Conditions (a), (b), (c) and (d)
(a) After ignition switch ON and engine not running time
Less than 20 seconds
(b) Soak Time
7 hours or more
(c) Battery voltage
10.5 V or higher
(d) Time after engine start
15 seconds or more
2. Either of the following conditions are met
Condition (a) and (b)
(a) Minimum IAT after engine start
-10°C (14°F) or higher
(b) ECT before engine start
-10°C (14°F) or higher

TYPICAL MALFUNCTION THRESHOLDS


Deviated temperature (difference between ECT and IAT)
Below -20°C (-36°F) or higher than 20°C (36°F)

CONFIRMATION DRIVING PATTERN


A213993E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) [A].
  4. Turn the ignition switch off.
  5. With the engine stopped, leave the vehicle as is for 7.5 hours or more [B].
  6. Start the engine and wait 60 seconds or more [C].
  7. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  8. Read the Pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  10. Input the DTC: P011B.
  11. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU's memory limit

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or N/A, perform steps [A] through [D] again.

  12. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO P011B)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    Result:

    Result
    Proceed to
    P011B
    A
    P011B and other DTCs
    B

    HINT:
    If any DTCs other than P011B are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.READ VALUE USING TECHSTREAM (INTAKE AIR TEMPERATURE)
  1. Leave the vehicle for 7 hours or more.

    HINT:
    It is necessary leave the vehicle for 7 hours or more to allow conditions similar to the DTC detection conditions.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / All Data / Intake Air.

  1. Read the value displayed on the Techstream.

    OK:
    Difference between the intake air temperature and the actual outside air temperature is within 10°C (18°F).

    HINT:
    Temperature readings on the vehicle outside temperature gauge (if equipped) are not suitable for comparing to the IAT reading. The outside temperature gauge has a significant delay built-in to prevent temperature swings from being displayed on its display. Use an accurate thermometer to determine the outside air temperature.



NG
REPLACE MASS AIR FLOW METER (Click here)
OK


3.READ VALUE USING TECHSTREAM (COOLANT TEMPERATURE)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / All Data / Coolant Temp.

  1. Read the value displayed on the Techstream.

    OK:
    The difference between the coolant temperature and the actual outside air temperature is within 10°C (18°F).

    HINT:
    If the result is not as specified, check that there are heat sources such as a block heater in the engine compartment.



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK

REPLACE ECM (Click here)