NAVIGATION SYSTEM (for DVD) > Illumination Circuit |

| 1.CHECK ILLUMINATION |
Check if the illumination for the navigation receiver assembly, steering pad switch, glove box or other parts (hazard switch, transmission control switch, etc.) come on when the light control switch is turned to the HEAD or TAIL position.
| Result | Proceed to |
| Illumination comes on for all components except steering pad switch. | A |
| Illumination comes on for all components except navigation receiver assembly. | B |
| No illumination comes on (navigation receiver, hazard switch, glove box, etc.). | C |
| Illumination comes on for all components except steering pad switch and navigation receiver assembly. | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - BATTERY) |
![]() |
Disconnect the J45 spiral cable sub-assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| J45-12 (IL+2) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
|
| ||||
| OK | |
| 3.INSPECT STEERING PAD SWITCH ASSEMBLY |
Remove the steering pad switch assembly (Click here).

Connect the positive (+) lead of the battery to terminal 5 (IL+2) and the negative (-) lead of the battery to terminal 8 (EAU) of the steering pad switch assembly connector.
Check if the illumination for the steering pad switch assembly comes on.
|
| ||||
| OK | |
| 4.INSPECT SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Remove the spiral cable sub-assembly (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z3-8 (EAU) - J45-4 (EAU) | Spiral cable is turned 2.5 rotations counterclockwise | Below 1 Ω |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise | ||
| z3-5 (IL+2) - J45-12 (IL+2) | Spiral cable is turned 2.5 rotations counterclockwise | |
| Spiral cable is centered | ||
| Spiral cable is turned 2.5 rotations clockwise |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - SPIRAL CABLE) |
![]() |
Disconnect the K21 navigation receiver assembly connector.
Disconnect the J45 spiral cable sub-assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K21-6 (SWG) - J45-4 (EAU) | Always | Below 1 Ω |
| K21-6 (SWG) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - BATTERY) |
![]() |
Disconnect the K18 navigation receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| K18-2 (ILL+) - Body ground | Light control switch TAIL or HEAD | 11 to 14 V |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - COMBINATION METER) |
![]() |
Disconnect the K18 navigation receiver assembly connector.
Disconnect the J28 combination meter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K18-12 (ILL-) - J28-37 (ILL-) | Always | Below 1 Ω |
| K18-12 (ILL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||