Home › BRAKE › BRAKE › FRONT BRAKE

FRONT BRAKE > INSTALLATION

for Preparation Click here



1. INSTALL FRONT DISC


    C155464E01
  1. Align the matchmarks, and then install the front disc.

    HINT:
    When replacing the front disc with a new one, select the installation position where the front disc has the smallest runout.



2. INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY LH


    C154478
  1. Install the disc brake caliper with 2 new bolts.

    Torque:
    99 N*m{ 1010 kgf*cm , 73 ft.*lbf }



3. CONNECT NO. 7 FRONT BRAKE TUBE


    C208567
  1. Using a union nut wrench, connect the front brake tube.

    Torque:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }

    NOTICE:
    Use the formula to calculate special torque values for situations where a union nut wrench is combined with a torque wrench (Click here).



4. INSTALL FRONT DISC BRAKE PAD KIT


    C155459E01
  1. Apply a light coat of disc brake grease to both sides of the No. 1 anti-squeal shims.

  1. Install the No. 1 and No. 2 anti-squeal shims to each pad.



    C155460
  1. Install the 2 pads to the disc brake caliper.



    C155461
  1. Install the front disc brake anti-rattle spring between the 2 pads.

    NOTICE:
    The anti-rattle spring can be used again if it has sufficient rebound; no deformation, cracks or wear; and has had all rust, dirt and foreign matter cleaned off.



    C154476
  1. Install the 2 hole pins.

  1. Install the pin hold clip.

    NOTICE:
    The pin hold clip can be used again if it has sufficient rebound; no deformation or wear; and has had all rust, dirt and foreign matter cleaned off.



5. BLEED BRAKE LINE
  1. Bleed brake line

    1. Remove the brake master cylinder reservoir filler cap assembly.

    2. Add brake fluid into the reservoir between MAX and MIN level on the brake fluid reservoir.

      Brake fluid:
      SAE J1703 or FMVSS No. 116 DOT3

    3. Connect a vinyl tube to the bleeder plug of the front disc brake cylinder RH.

    4. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1

    5. When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal.*2

    6. Repeat *1 and *2 until all the air in the brake fluid is completely bled out and the new brake fluid comes out.

    7. Tighten the bleeder plug completely.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    8. Replace the brake fluid from the front disc brake cylinder LH using the same procedure as for RH.

    9. Connect a vinyl tube to the bleeder plug of the rear disc brake cylinder RH.

    10. Depress the brake pedal several times, and then loosen the bleeder plug with the pedal depressed.*1

    11. When fluid stops coming out, tighten the bleeder plug, and then release the brake pedal.*2

    12. Repeat *1 and *2 until all the air in the brake fluid is completely bled out and the new brake fluid comes out.

    13. Tighten the bleeder plug completely.

      Torque:
      11 N*m{ 110 kgf*cm , 8 ft.*lbf }

    14. Replace the brake fluid from the rear disc brake cylinder LH using the same procedure as for RH.

  1. Check and bleed brake system.

    1. If the following malfunction symptoms occur, air may have entered the brake fluid line. Perform the following air bleed procedures.

      1. Low pedal or spongy pedal.
      2. Brake pedal is depressed firmly but braking is insufficient.

  1. Check and adjust brake fluid level in reservoir .



6. INSTALL FRONT WHEEL

Torque:
for Aluminum Wheel:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
for Steel Wheel:
209 N*m{ 2131 kgf*cm , 154 ft.*lbf }