DTC P2440 Secondary Air Injection System Switching Valve Stuck Open Bank1 |
DTC P2441 Secondary Air Injection System Switching Valve Stuck Close Bank1 |
DTC P2442 Secondary Air Injection System Switching Valve Stuck Open Bank 2 |
DTC P2443 Secondary Air Injection System Switching Valve Stuck Closed Bank 2 |
| DTC No. | DTC Detection Condition | Trouble Area |
| P2440 | Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic). |
|
| The air switching valve (for bank 1) is stuck open for 7 seconds while the engine is running (2 trip detection logic). | ||
| P2441 | The air switching valve (for bank 1) is stuck close for 7 seconds while the engine is running (2 trip detection logic). |
|
| P2442 | Cumulative pressure pulsation is 60 kPa (450 mmHg) or more for 2 seconds (1 trip detection logic). |
|
| The air switching valve (for bank 2) is stuck open for 7 seconds while the engine is running (2 trip detection logic). | ||
| P2443 | The air switching valve (for bank 2) is stuck close for 7 seconds while the engine is running (2 trip detection logic). |
|
| Related DTCs | P2440: Air control valve stuck open P2441: Air control valve stuck closed P2442: Air control valve stuck open P2443: Air control valve stuck closed |
| Required Sensors/Components (Main) | Pressure sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Once per drive cycle |
| Duration | 2 seconds: P2440 Case 2, P2442 Case 2 7 seconds: Others |
| MIL Operation | 1 driving cycle: P2440 Case 2, P2442 Case 2 2 driving cycles: Others |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | P0010, P0020 (VVT oil control valve) P0011, P0021 (VVT system - Advance) P0012, P0022 (VVT system - Retard) P0013, P0023 (Exhaust VVT oil control valve) P0014, P0024 (Exhaust VVT system - Advance) P0015, P0025 (Exhaust VVT system - Retard) P0016, P0018 (VVT system - Misalignment) P0017, P0019 (Exhaust VVT system - Misalignment) P0031, P0032, P0051, P0052, P101D, P103D (Air fuel ratio sensor heater) P006A, P0107, P0108 (Manifold absolute pressure) P0102, P0103 (Mass air flow meter) P0112, P0113 (Intake air temperature sensor) P0115, P0117, P0118 (Engine coolant temperature sensor) P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle position sensor) P0125 (Insufficient coolant temperature for closed loop fuel control) P014C, P014D, P014E, P014F, P015A, P015B, P015C, P015D, P2195, P2196, P2197, P2198, P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255, P2256 (Front oxygen/Air fuel ratio sensor) P0171, P0172, P0174, P0175 (Fuel system) P0301 - P0308 (Misfire) P0327, P0328, P0332, P0333, P032C, P032D, P033C, P033D (Knock sensor) P0335 (Crankshaft position sensor) P0340, P0342, P0343, P0345, P0347, P0348 (VVT sensor) P0351 - P0358 (Igniter) P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT sensor) P0401 (EGR system) P0451, P0452, P0453 (EVAP system) P0500, P0722 (Vehicle speed sensor) P106B (Evap. emission control system pressure sensor - Air injection system pressure sensor correlation) P1340 (Camshaft position sensor) P2431, P2432, P02433, P2436, P2437, P2438 (Secondary air injection system pressure sensor) |
| Battery voltage | 11 V or more |
| Atmospheric pressure | 45 kPa (338 mmHg) or more |
| Engine | Running |
| AIR monitor during AIR: ON*1 | Completed |
| AIR monitor during AIR: OFF*2 | Completed |
| AIR injection driver fail (open/short or out of range) | Not detected |
| AIR pressure sensor fail (open/short or out of range) | Not detected |
| *1: AIR monitor during AIR: ON | - |
| Time after AIR in operation | 5 seconds or more |
| AIR pump | ON |
| AIR valve | Open |
| Engine speed | 400 to 3750 rpm |
| Intake air amount | Less than 100 gm/s |
| Time after engine start | 1 second or more |
| *2: AIR monitor during AIR: OFF | - |
| Time after AIR in operation | 10 seconds or more |
| AIR pump | OFF |
| AIR valve | Close |
| Engine speed | Below 3000 rpm |
| AIR monitor during AIR: ON | Completed |
| Time after engine start | 1 second or more |
| One of the following conditions is met | (a), (b) or (c) |
| (a) Cumulative intake air amount | 100 gm/s or more |
| (b) Difference between starting temperature and current temperature | 10°C (18°F) or higher |
| (c) Starting coolant temperature | 45°C (113°F) or higher |
| AIR pump | OFF |
| AIR valve | Close |
| Engine speed | 5000 rpm or less |
| AIR pressure sensor fail (open/short or out of range) | Not detected |
| Time after engine started | 1 second or more |
| Time after AIR in operation | 10 seconds or more |
| AIR valve open stuck | Not detected |
| AIR pressure sensor open stuck (DTC P2445, P2447) | Not in operation |
| Engine load | 20% or more |
| Both conditions are met during AIR ON | - |
| Cumulative pressure pulsation | 18 kPa or higher |
| AIR pressure | 1.9 kPa or higher |
| Both conditions are met during AIR ON | - |
| Cumulative pressure pulsation | 18 kPa or higher |
| AIR pressure | Below 1.9 kPa |
| Both conditions are met during AIR ON | - |
| Cumulative pressure pulsation | Below 18 kPa |
| AIR pressure | 1.9 kPa or higher |
| Both conditions are met during AIR ON | - |
| Cumulative pressure pulsation | Below 18 kPa |
| AIR pressure | Below 1.9 kPa |
| Both conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | 25 kPa or higher |
| AIR pressure | 3 kPa or higher |
| Both conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | 25 kPa or higher |
| AIR pressure | Below 3 kPa |
| Both conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | Below 25 kPa |
| AIR pressure | 3 kPa or higher |
| Both conditions are met during AIR OFF | - |
| Cumulative pressure pulsation | Below 25 kPa |
| AIR pressure | Below 3 kPa |
| Either condition is met | (a) or (b) |
| (a) AIR OFF Condition 1 | Met |
| (b) AIR OFF Condition 2 | Met |
| Either condition is met | (a) or (b) |
| (a) AIR ON Condition 3 | Met |
| (b) AIR ON Condition 4 | Met |
| Cumulative pressure pulsation | 75 kPa or higher |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| Air Pump | ON |
| Air Switching Valve | Open |
| Pressure | 1.9 kPa or more |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Air Switching Valve | Open |
| Pressure | Less than 3.0 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Air Switching Valve | Closed |
| Pressure | 1.9 kPa or more |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Air Switching Valve | Closed |
| Pressure | Less than 3.0 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | ON |
| Air Switching Valve | Open |
| Pressure | 1.9 kPa or more |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | OFF |
| Air Switching Valve | Open |
| Pressure | Less than 3.0 kPa |
| Pulsation Detection | Exhaust gas pulsation detected |
| Air Pump | ON |
| Air Switching Valve | Closed |
| Pressure | 1.9 kPa or more |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Air Pump | OFF |
| Air Switching Valve | Closed |
| Pressure | Less than 3.0 kPa |
| Pulsation Detection | Exhaust gas pulsation not detected |
| Detected Condition while AIR Operating: Air Pump ON, ASV Open | Detected Condition while AIR not Operating: Air Pump OFF, ASV Closed | ECM Determination | DTC Output |
| Case 1 | Case 8 | Normal | - |
| Case 1 | Case 6 | ASV stuck open | P2440 or P2442 |
| Case 1 | Case 7 | Air pump stuck ON | P2444 or P2446 |
| Case 2 | Case 8 | Air pump stuck OFF | P2445 or P2447 |
| Case 3 | Case 8 | ASV stuck closed | P2441 or P2443 |
| Case 1 | Case 5 | ASV stuck open and air pump stuck ON | P2440 and P2444 or P2442 and P2446 |
| Case 2 | Case 6 | ASV stuck open and air pump stuck OFF | P2440 and P2445 or P2442 and P2447 |
| Case 3 | Case 7 | ASV stuck closed and air pump stuck ON | P2441 and P2444 or P2443 and P2446 |
| Case 4 | Case 8 | ASV stuck closed and air pump stuck OFF | P2441 and P2445 or P2443 and P2447 |
| Tester Operation | Air Pump | ASV | Pressure*1 | Pulsation*2 |
| AIR PUMP: ON, ASV: OPEN | ON | OPEN | 1.9 kPa or more | 18 kPa or more |
| AIR PUMP: OFF, ASV: CLOSE | OFF | CLOSE | Less than 3.0 kPa | Less than 25 kPa |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO SECONDARY AIR INJECTION SYSTEM DTCS) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| P2440, P2441, P2442 and/or P2443 is output | A |
| P2440, P2441, P2442 and/or P2443 and P0412 and/or P0415 are output | B |
| P2440, P2441, P2442 and/or P2443 and other DTCs (except P0412 and P0415) are output | C |
|
| ||||
|
| ||||
| A | |
| 2.PERFORM ACTIVE TEST USING TECHSTREAM (SECONDARY AIR INJECTION SYSTEM OPERATION) |
![]() |
Visual check:
Start the engine and warm it up.
Turn the ignition switch off.
Disconnect the No. 1 air hose.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Place your hand near the air switching valve port and check that the exhaust gas pressure pulsates when the ASV is turned ON.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: ON, ASV1: CLOSE, AIR PUMP 2: ON, ASV2: CLOSE.
Check that the exhaust gas does not pulsate when the ASV is turned OFF.
Turn the ignition switch off.
| Air Pump Operation | ASV Operation | Exhaust Gas Pulsation |
| ON | OFF | Not detected |
| ON | ON | Detected |
Other inspection method:
The ASV operation can be confirmed by checking the cumulative pressure pulsation* provided in the System Check.
Perform System Check operation under Manual Mode.
*: The exhaust pulsation value is calculated in the ECM. If the calculated value exceeds a certain level, the ECM determines that the exhaust pulsation is in the AIR system.
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV1: OPEN, AIR PUMP 2: ON, ASV2: OPEN and AIR PUMP 1: OFF, ASV1: CLOSE, AIR PUMP 2: OFF, ASV2: CLOSE.
Start the engine after the Techstream initialization is finished.
Perform the AIR system forced operation while the engine is idling.
Check that the air-fuel ratio and pressure in the secondary air injection system passage (PULSATION) displayed on the Techstream indicate the conditions shown in the table below.
Turn the ignition switch off.
| AIR System Operation | Pulsation Condition (ECM Calculation) | Air-Fuel Ratio (Reference) |
| AIR PUMP: ON, ASV: OPEN | 18 kPa or more | 18 or more |
| AIR PUMP: OFF, ASV: CLOSE | Less than 25 kPa | Approximately 14.5 (around stoichiometric air-fuel ratio) |
| Result | Proceed to |
| NG | A |
| OK | B |
|
| ||||
| A | |
| 3.INSPECT AIR TUBE (BLOCKAGE AND LEAK) |
![]() |
Check that the No. 2 and No. 3 air tubes are securely connected to both the exhaust manifold and the ASV.
Inspect the air tube for blockages and damage.
|
| ||||
| OK | |
| 4.INSPECT AIR SWITCHING VALVE |
Inspect the air switching valve for bank 1 .
Inspect the air switching valve for bank 2 .
|
| ||||
| OK | |
| 5.INSPECT AIR INJECTION CONTROL DRIVER (POWER SOURCE OF AIR INJECTION CONTROL DRIVER) |
![]() |
Disconnect the AID connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D48-1 (BATT) - Body ground | Always | 11 to 14 V (near battery voltage) |
| D50-5 (+B) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
| D52-1 (BAT2) - Body ground | Always | 11 to 14 V (near battery voltage) |
| D54-5 (+B2) - Body ground | Ignition switch ON | 11 to 14 V (near battery voltage) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D50-1 (E) - Body ground | Always | Below 1 Ω |
| D54-1 (E2) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (ECM - AIR INJECTION CONTROL DRIVER) |
![]() |
Disconnect the ECM connectors.
Disconnect the AID connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D74-28 (AIRV) - D50-3 (SIV) | Always | Below 1 Ω |
| A24-43 (ARV2) - D54-3 (SIV2) | Always | Below 1 Ω |
| D74-28 (AIRV) or D50-3 (SIV) - Body ground | Always | 10 kΩ or higher |
| A24-43 (ARV2) or D54-3 (SIV2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.PERFORM ACTIVE TEST USING TECHSTREAM |
![]() |
Disconnect the AID connector.
Connect terminals DI and SIV or DI2 and SIV2 of the wire harness connector for the AID.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Measure the voltage between the SIV and E or SIV2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| D50-3 (SIV) - D50-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D54-3 (SIV2) - D54-1 (E2) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D50-3 (SIV) - D50-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
| D54-3 (SIV2) - D54-1 (E2) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
![]() |
Connect terminals DI and SIP or DI2 and SIP2 of the wire harness connector for the AID.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Manual Mode / AIR PUMP 1: ON, ASV 1: OPEN, AIR PUMP 2: ON, ASV 2: OPEN.
Start the engine.
Perform the AIR system forced operation while the engine is idling.
Measure the voltage between the SIP and E or SIP2 and E2 terminals of the ECM connector when the AIR system is ON and OFF.
Turn the ignition switch off.
| Tester Connection | Condition | Specified Condition |
| D50-4 (SIP) - D50-1 (E) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D54-4 (SIP2) - D54-1 (E2) | AIR PUMP: ON, ASV: OPEN | 0.5 to 2 V |
| D50-4 (SIP) - D50-1 (E) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
| D54-4 (SIP2) - D54-1 (E2) | AIR PUMP: OFF, ASV: CLOSE | 11 to 14 V |
|
| ||||
| OK | |
| 8.REPLACE AIR INJECTION CONTROL DRIVER |
Replace the air injection control driver (Click here).
| NEXT | |
| 9.CHECK WHETHER DTC OUTPUT RECURS (DTC P2440, P2441, P2442 AND/OR P2443) |
Start the engine and warm it up.
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Clear DTCs (if set) (Click here).
Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.
Start the engine after the Techstream initialization is finished.
Perform the System Check operation by pressing ENTER (Next).
After operating the AIR system, perform the following to confirm the AIR system pending codes: Press the Exit button.
Check pending DTCs.
Turn the ignition switch off.
|
| ||||
| OK | ||
| ||
| 10.INSPECT AIR SWITCHING VALVE (PRESSURE SENSOR) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Air pump pressure (Absolute) and Air Pump2 Pressure (Absolute).
Check the pressure displayed on the Techstream.
|
| ||||
| OK | ||
| ||