Home › BODY › WINDSHIELD / WINDOWGLASS › WINDSHIELD GLASS

WINDSHIELD GLASS > INSTALLATION

for Preparation Click here



1. INSTALL NO. 2 WINDSHIELD GLASS STOPPER
  1. Apply Primer G to the glass where the spacers will be installed.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Install 2 new stoppers onto the glass as shown in the illustration.


    B166395E03

    Standard:
    Area
    Specified Condition
    a
    8.5 mm (0.334 in.)



2. INSTALL NO. 1 WINDSHIELD GLASS STOPPER


B106096E03
  1. Install 2 new stoppers to the vehicle body as shown in the illustration.



3. INSTALL WINDSHIELD GLASS ADHESIVE DAM
  1. Apply Primer G to the glass where the glass adhesive dams will be installed.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Remove the peeling paper from the adhesive part of the dam. While aligning the dam to the ceramic notch and dam reference line, install the dam (adhesive side) to the glass (Primer G area).


    B166396E01

    Standard:
    Area
    Specified Condition
    a
    29.2 mm (1.15 in.)



4. INSTALL UPPER WINDSHIELD OUTSIDE MOULDING


B166397E01
  1. Using a brush or sponge, coat the edge of the glass and the contact surface with Primer G.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.

  1. Install the windshield outside moulding, as shown in the illustration.

    NOTICE:
    Do not drive the vehicle for the amount of time written in the table below.

    Usage time frame:
    Temperature
    Usage Time Frame
    35°C (95°F)
    15 minutes
    20°C (68°F)
    1 hour 40 minutes
    5°C (41°F)
    8 hours



5. INSTALL WINDSHIELD GLASS


    B106085E04
  1. Using a brush, apply Primer M to the exposed part of the vehicle body.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Do not apply primer to the adhesive.
    3. Throw away any leftover primer.
    4. Do not apply too much primer.



  1. Using a brush or sponge, apply Primer G to the contact surface of the glass.


    B171649E01

    HINT:
    If the primer is applied to an area that is not specified, apply non-residue solvent to a clean cloth and wipe off the excess primer.

    NOTICE:
    1. Allow the primer to dry for 3 minutes or more.
    2. Throw away any leftover primer.
    3. Do not apply too much primer.



  1. Apply adhesive to the glass.

    Adhesive:
    Toyota Genuine Windshield Glass Adhesive or equivalent


    1. Cut off the tip of the cartridge nozzle as shown in the illustration.

      HINT:
      After cutting off the tip, use all adhesive within the time written in the table below.

      Usage time frame:
      Temperature
      Usage Time Frame
      35°C (95°F)
      15 minutes
      20°C (68°F)
      1 hour 40 minutes
      5°C (41°F)
      8 hours

    2. Load the sealer gun with the cartridge.



    3. Apply adhesive to the glass as shown in the illustration.


      B171650E01

      Standard:
      Area
      Specified Condition
      a
      12.0 mm (0.472 in.)
      b
      8.0 mm (0.315 in.)
      c
      4.0 mm (0.157 in.)



    B166394E01
  1. Install the glass to the vehicle body.

    1. Using suction cups, position the glass so that the matchmarks are aligned. Press it in gently along the rim.

    2. Lightly press the outer surface of the glass to ensure that it is securely fit to the vehicle body.

      NOTICE:
      1. Check that the stoppers are attached to the vehicle body correctly.
      2. Check that the vehicle body and glass have a small gap between them.

    3. Hold the glass in place securely with protective tape or equivalent until the adhesive hardens.

  1. w/ Windshield Deicer:
    Install the clip and connect the connector.



6. INSTALL WINDSHIELD MOULDING OUTSIDE


B166398E01
  1. Install the windshield outside moulding, as shown in the illustration.

  1. Apply Primer G to the windshield outside moulding area "a" shown in the illustration.



7. CHECK FOR LEAK AND REPAIR
  1. Conduct a leak test after the adhesive has completely hardened.

  1. Seal any leaks with auto glass sealer.



8. INSTALL ROOF DRIP SIDE FINISH MOULDING CLIP

HINT:
Perform this procedure only when installing new clips.

  1. Using a heat light, heat the clip installation areas on the vehicle body.

  1. Remove the double-sided tape from the vehicle body.

  1. Wipe off any tape adhesive residue with cleaner.

  1. Using a heat light, heat the clips.

  1. Remove the peeling paper from the face of the clips.

    HINT:
    After removing the peeling paper, keep the exposed adhesive free from foreign matter.



  1. Install the clips in the positions shown in the illustration.

    HINT:
    Press the clips firmly to install them.



    B168261E03



9. INSTALL ROOF DRIP SIDE FINISH MOULDING LH


  1. Attach the clip to install the moulding.


    B168262E03



10. INSTALL ROOF DRIP SIDE FINISH MOULDING RH

HINT:
Use the same procedures described for the LH side.



11. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING LH
  1. Clean the vehicle body surface.

    1. Using a heat light, heat the vehicle body surface.

    2. Remove the double-sided tape from the vehicle body.

    3. Wipe off any tape adhesive residue with cleaner.



  1. If reusing the moulding:
    Clean the moulding.

    1. Using a heat light, heat the moulding.

    2. Remove the double-sided tape from the moulding.

    3. Wipe off any tape adhesive residue with cleaner.



    4. B163286E01
    5. Apply new double-sided tape to the moulding, as shown in the illustration.



  1. Install the moulding.

    1. Using a heat light, heat the vehicle body and moulding.

    2. Remove the peeling paper from the face of the moulding.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.



    3. B163282E03
    4. Attach the clip to install the moulding.

      HINT:
      Press the moulding firmly to install it.



12. INSTALL REAR ROOF DRIP SIDE FINISH MOULDING RH

HINT:
Use the same procedures described for the LH side.



13. INSTALL ROOF HEADLINING ASSEMBLY
  1. Return the roof headlining to its original position.



14. INSTALL ASSIST GRIP PLUG


B165717
  1. Install a new assist grip plug.



15. INSTALL ASSIST GRIP SUB-ASSEMBLY
  1. for Regular Cab, for Double Cab:
    Install the assist grip .

  1. for CrewMax:
    Install the assist grip .



16. INSTALL VISOR HOLDER
  1. for Regular Cab:
    Install the visor holder .

  1. for Double Cab, w/o Illumination:
    Install the visor holder .

  1. for CrewMax, w/o Illumination:
    Install the visor holder .



17. INSTALL VISOR ASSEMBLY LH
  1. for Regular Cab:
    Install the visor .

  1. for Double Cab:
    Install the visor .

  1. for CrewMax:
    Install the visor .



18. INSTALL VISOR ASSEMBLY RH

HINT:
Use the same procedures described for the LH side.



19. INSTALL VISOR BRACKET COVER LH


B166262
  1. Attach the 4 claws to install the visor bracket cover.



20. INSTALL VISOR BRACKET COVER RH

HINT:
Use the same procedures described for the LH side.



21. INSTALL ROOF CONSOLE BOX ASSEMBLY
  1. for Short Type:
    Install the roof console box (Click here).

  1. for Long Type:
    Install the roof console box (Click here).



22. INSTALL INNER REAR VIEW MIRROR ASSEMBLY
  1. w/ EC Mirror:
    Install the inner rear view mirror .

  1. w/o EC Mirror:
    Install the inner rear view mirror .



23. INSTALL INNER REAR VIEW MIRROR STAY HOLDER COVER (w/ EC Mirror)


B227101
  1. Attach the 2 claws of the inner rear view mirror stay holder cover to the mirror, and then slide the inner rear view mirror stay holder cover in the direction indicated by the arrow in the illustration to attach the 2 claws to the roof headlining and install the inner rear view mirror stay holder cover.



24. INSTALL FRONT PILLAR GARNISH LH
  1. Attach the claw to install the front pillar garnish.

  1. Install the assist grip with the 2 bolts.



  1. Attach the 2 claws to install the 2 assist grip plugs.


    B165706



25. INSTALL FRONT PILLAR GARNISH RH

HINT:
Use the same procedures described for the LH side.



26. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP LH


27. INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH


28. INSTALL COWL TOP VENTILATOR LOUVER SUB-ASSEMBLY


    E146307
  1. Push the ventilator louver in the direction indicated by the arrow in the illustration to attach 8 claws and 2 clips, and install the ventilator louver.



29. INSTALL FRONT FENDER TO COWL SIDE SEAL LH
  1. Attach the claw to install the cowl side seal.



30. INSTALL FRONT FENDER TO COWL SIDE SEAL RH

HINT:
Use the same procedures described for the LH side.



31. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY LH


    E146308E01
  1. Stop the wiper motor at the automatic stop position.

  1. Clean the wiper arm serration with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.



    E146317E01
  1. Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

    Standard measurement:
    Position
    Specified Condition
    A
    23.9 mm (0.941 in.)
    B
    35.5 mm (1.40 in.)

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.



32. INSTALL FRONT WIPER ARM AND BLADE ASSEMBLY RH


    E146308E01
  1. Stop the wiper motor at the automatic stop position.

  1. Clean the wiper arm serration with a round file or equivalent.

  1. Clean the wiper pivot serration with a wire brush.



    E146310E01
  1. Install the wiper arm and blade with the nut. Make sure that the wiper arm and blade comes to the position shown in the illustration.

    Standard measurement:
    Position
    Specified Condition
    A
    11.5 mm (0.453 in.)
    B
    29.8 mm (1.17 in.)

    Torque:
    25 N*m{ 255 kgf*cm , 18 ft.*lbf }

    HINT:
    Hold down the wiper arm hinge with your hand while tightening the nut.

  1. Operate the front wipers while spraying washer fluid on the windshield glass. Make sure that the front wipers function properly and there is no interference with the vehicle body.