Home › DRIVE LINE › DIFFERENTIAL › DIFFERENTIAL CARRIER ASSEMBLY (for 1GR-FE, 1UR-FE)

DIFFERENTIAL CARRIER ASSEMBLY (for 1GR-FE, 1UR-FE) > REASSEMBLY

for Preparation Click here



1. INSTALL REAR DIFFERENTIAL DYNAMIC DAMPER (for Regular Cab Standard Deck)


    C160325
  1. Install the dynamic and washer damper with the bolt.

    Torque:
    17 N*m{ 168 kgf*cm , 12 ft.*lbf }



2. INSTALL REAR DIFFERENTIAL DUST DEFLECTOR


    C124176E01
  1. Using SST, a press and steel plate, press in the dust deflector.

    SST
    09523-36010  

    NOTICE:
    Be careful not to damage the dust deflector.



3. INSTALL DIFFERENTIAL CASE ASSEMBLY


    C124142
  1. Install the 2 side gear thrust washers to the side gears.

  1. Install the 2 side gears with the thrust washers, 2 pinion gears, 2 pinion gear thrust washers and pinion shaft.

    HINT:
    1. Align the holes for the straight pin in the differential case and pinion shaft.
    2. Apply hypoid gear oil to each sliding surface and rotating part.



    C124143
  1. Using a dial indicator, measure the side gear backlash while holding one pinion gear toward the differential case.

    Standard backlash:
    0.05 to 0.20 mm (0.00197 to 0.00788 in.)

    If the backlash is not within the specified value, replace the side gear thrust washer with an appropriate thickness.

    HINT:
    Refer to the following table to select thrust washers which will ensure that the backlash is within the specified value.


    Washer thickness:

    Thickness
    Thickness
    1.53 to 1.57 mm (0.0602 to 0.0618 in.)
    1.78 to 1.82 mm (0.0701 to 0.0171 in.)
    1.58 to 1.62 mm (0.0622 to 0.0638 in.)
    1.83 to 1.87 mm (0.0720 to 0.0736 in.)
    1.63 to 1.67 mm (0.0642 to 0.0657 in.)
    1.88 to 1.92 mm (0.0740 to 0.0756 in.)
    1.68 to 1.72 mm (0.0661 to 0.0677 in.)
    1.93 to 1.97 mm (0.0760 to 0.0776 in.)
    1.73 to 1.77 mm (0.0681 to 0.0697 in.)
    -



    C124144
  1. Using a pin punch and hammer, tap the straight pin through the holes in the differential case and pinion shaft.

  1. Using a chisel and hammer, stake the outside of the differential case pin hole.



4. INSTALL REAR DIFFERENTIAL CASE BEARING


    C186902E01
  1. Using SST and a press, press in the 2 bearings.

    SST
    09710-30050  
    09950-60010   (09951-00480)
    09950-70010   (09951-07150)



5. INSTALL DIFFERENTIAL RING GEAR


    SA01143E06
  1. Clean the contact surfaces of the differential case and ring gear.

  1. Heat the ring gear to approximately 100°C (212°F) in boiling water.

  1. Carefully take the ring gear out of the boiling water.



    C159774E01
  1. After the moisture on the ring gear has completely evaporated, quickly set the ring gear onto the differential case.

    HINT:
    Align the matchmarks on the ring gear and differential case.

  1. After the ring gear cools down sufficiently, apply adhesive to the bolts and install them.

    Adhesive:
    Toyota Genuine Adhesive 1360K, Three Bond 1360K or equivalent

    Torque:
    137 N*m{ 1397 kgf*cm , 101 ft.*lbf }



6. INSPECT DIFFERENTIAL RING GEAR RUNOUT


    C159775
  1. Install the differential case onto the carrier, and install the 2 adjusting nuts so that there is no play in the bearing.

  1. Install the 2 bearing caps with the 4 bolts.

  1. Install the 2 adjusting nut locks with the 2 bolts.

  1. Using a dial indicator, measure the runout of the ring gear.

    Maximum runout:
    0.05 mm (0.00197 in.)

    If the runout is greater than the maximum, replace the ring gear.

  1. Remove the 2 bolts and adjusting nut locks.

  1. Remove the 2 bearing caps, 2 adjusting nuts and differential case assembly.



7. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C091048E03
  1. Using SST and a press, press in the bearing (outer race).

    SST
    09950-60020   (09951-00710)
    09950-70010   (09951-07150)



8. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    C186903E01
  1. Using SST and a press, press in the bearing (outer race).

    SST
    09950-60020   (09951-00890)
    09950-70010   (09951-07150)



9. INSTALL REAR DRIVE PINION REAR TAPERED ROLLER BEARING


    SA03102E05
  1. Install the plate washer onto the drive pinion.

    HINT:
    First fit a washer with the same thickness as the removed washer, and then check the tooth contact pattern. Replace the washer with one of a different thickness if necessary.

  1. Using SST and a press, press in the rear bearing (inner race).

    SST
    09506-35010  



10. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


    C028218
  1. Install the drive pinion, front bearing (inner race) and oil slinger.

    HINT:
    Assemble the spacer and oil seal after adjusting the gear contact pattern.



    C187382E01
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09956-03050)
    09955-03050  



    ZK09978E03
  1. Using SST to hold the companion flange.

    SST
    09330-00021   (09330-00030)

  1. Coat the threads of the nut with hypoid gear oil.

  1. Install the nut by tightening it until the standard preload is reached.

    Torque:
    441 N*m{ 4497 kgf*cm , 325 ft.*lbf } or less

    NOTICE:
    As there is no spacer, tighten the nut a little at a time, being careful not to overtighten it.



    C003092
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Standard preload (at starting):
    Bearing
    Specified Condition
    New
    1.04 to 1.69 N*m (11 to 17 kgf*cm, 10 to 14 in.*lbf)
    Reused
    0.85 to 1.37 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf)

    HINT:
    Measure the total preload after first turning the bearing clockwise and counterclockwise several times to make the bearing smooth.



11. INSTALL REAR DIFFERENTIAL CASE ASSEMBLY


    C028220
  1. Place the 2 bearing outer races on their respective bearings.

    NOTICE:
    Do not interchange the right and left race.



12. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT


    C028221E01
  1. Install the 2 adjusting nuts onto the carrier, making sure the nuts are threaded properly.



13. INSPECT AND ADJUST DIFFERENTIAL RING GEAR AND DIFFERENTIAL DRIVE PINION BACKLASH


    C159776E01
  1. Align the matchmarks on the bearing cap and carrier.



    SA02474E01
  1. Install the right and left bearing caps with the 4 bolts.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }

    1. If the bearing cap does not fit tightly on the carrier, the adjusting nuts are not threaded properly. Reinstall the adjusting nuts if necessary.



    C159778E01
  1. Loosen the 4 bearing cap bolts to the point where the adjusting nuts can be turned using SST.

    SST
    09504-00011  

  1. Using SST, tighten the adjusting nut on the ring gear side until the ring has a backlash of about 0.2 mm (0.00788 in.).



    Z006917E04
  1. While turning the ring gear, use SST to tighten the adjusting nut on the drive pinion side. After the bearings have settled, loosen the adjusting nut on the drive pinion side.

    SST
    09504-00011  

  1. Using SST, tighten the adjusting nut 1 to 1.5 notches from the 0 preload position.



    C159778E01
  1. Using a dial indicator, adjust the ring gear backlash until it is within the specification.

    SST
    09504-00011  

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00788 in.)

    HINT:
    1. The backlash is adjusted by turning the left and right adjusting nuts an equal amount. For example, loosen the nut on the right side one notch and loosen the nut on the left side one notch.

    1. Perform the measurement at 3 or more positions around the circumference of the ring gear.



    C159776E01
  1. Tighten the bearing cap bolts.

    Torque:
    103 N*m{ 1050 kgf*cm , 76 ft.*lbf }



14. INSPECT TOTAL PRELOAD


    C003092
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard total preload (at starting):
    Standard drive pinion preload plus 0.24 to 0.46 N*m (3 to 4 kgf*cm, 3 to 4 in.*lbf)



15. INSPECT TOOTH CONTACT BETWEEN RING GEAR AND DRIVE PINION


C159779
  1. Coat 3 or 4 teeth at 3 different positions on the ring gear with Prussian blue.



  1. Turn the companion flange in both directions to inspect the ring gear for proper tooth contact.


    C116070E01


    1. C116071E01
      If the teeth are not contacting properly, use the following table to select a proper washer for correction.

      Washer thickness:

      Thickness
      Thickness
      1.04 to 1.06 mm (0.0409 to 0.0417 in.)
      1.315 to 1.335 mm (0.0518 to 0.0526 in.)
      1.065 to 1.085 mm (0.0420 to 0.0427 in.)
      1.34 to 1.36 mm (0.0528 to 0.0535 in.)
      1.09 to 1.11 mm (0.0419 to 0.0437 in.)
      1.365 to 1.385 mm (0.0537 to 0.0545 in.)
      1.115 to 1.135 mm (0.0439 to 0.0447 in.)
      1.39 to 1.41 mm (0.0547 to 0.0555 in.)
      1.14 to 1.16 mm (0.0449 to 0.0457 in.)
      1.415 to 1.435 mm (0.0558 to 0.0565 in.)
      1.165 to 1.185 mm (0.0459 to 0.0467 in.)
      1.44 to 1.46 mm (0.0567 to 0.0575 in.)
      1.19 to 1.21 mm (0.0469 to 0.0476 in.)
      1.465 to 1.485 mm (0.0577 to 0.0585 in.)
      1.215 to 1.235 mm (0.0478 to 0.0486 in.)
      1.49 to 1.51 mm (0.0587 to 0.0595 in.)
      1.24 to 1.26 mm (0.0488 to 0.0496 in.)
      1.515 to 1.535 mm (0.0597 to 0.0605 in.)
      1.265 to 1.285 mm (0.0498 to 0.0506 in.)
      1.54 to 1.56 mm (0.0607 to 0.0615 in.)
      1.29 to 1.31 mm (0.0508 to 0.0516 in.)
      -



16. REMOVE REAR DRIVE PINION NUT


    C124130E01
  1. Using SST to hold the companion flange, remove the nut.

    SST
    09330-00021   (09330-00030)



17. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C186905E01
  1. Using SST, remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09956-03030)
    09955-03050  



18. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


19. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C124133E01
  1. Using SST, remove the bearing (inner race).

    SST
    09556-22010  



20. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


    C159780
  1. Install a new spacer onto the drive pinion.



21. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    C028218
  1. Install the drive pinion, front bearing (inner race) and oil slinger.



    C187382E01
  1. Using SST and the companion flange, install the bearing (inner race) and then remove the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09956-03050)
    09955-03050  



22. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL


    C162201E01
  1. Using SST and a plastic-faced hammer, tap in a new oil seal until its surface is flush with the differential carrier end.

    SST
    09316-12010  
    09649-17010  

    Standard oil seal depth:
    0.05 to 0.95 mm (0.00197 to 0.0374 in.)

    HINT:
    Connect 2 SST with vinyl tape.

  1. Coat the lip of the oil seal with MP grease.



23. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C187382E01
  1. Using SST, install the companion flange.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09956-03030)
    09955-03050  



24. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD
  1. Coat the threads of a new nut with hypoid gear oil.



    ZK09978E03
  1. Using SST to hold the companion flange.

    SST
    09330-00021   (09330-00030)

  1. Tighten the nut until the standard preload is reached.

    Torque:
    441 N*m{ 4497 kgf*cm , 325 ft.*lbf } or less



    SA02352E01
  1. Using a torque wrench, measure the preload of the backlash between the drive pinion and ring gear.

    Standard preload (at starting):
    Bearing
    Specified Condition
    New
    1.04 to 1.69 N*m (11 to 17 kgf*cm, 10 to 14 in.*lbf)
    Reused
    0.85 to 1.37 N*m (9 to 13 kgf*cm, 8 to 12 in.*lbf)

    1. If the preload is greater than the maximum, replace the bearing spacer.
    1. If the preload is less than the minimum, retighten the nut with 13 N*m (130 kgf*cm, 9 ft.*lbf) of torque at a time until the specified preload is reached.

    Torque:
    441 N*m{ 4497 kgf*cm , 325 ft.*lbf } or less

    1. If the maximum torque is exceeded while retightening the nut, replace the bearing spacer and repeat the preload adjusting procedure.

    HINT:
    Do not loosen the pinion nut to reduce the preload.



25. INSPECT TOTAL PRELOAD


    C003092
  1. Using a torque wrench, measure the preload with the teeth of the drive pinion and ring gear in contact.

    Standard total preload (at starting):
    Standard drive pinion preload plus 0.24 to 0.46 N*m (3 to 4 kgf*cm, 3 to 4 in.*lbf)



26. INSPECT DIFFERENTIAL RING GEAR BACKLASH


C028211E01
  1. Using a dial indicator, check the backlash of the ring gear.

    Standard backlash:
    0.10 to 0.20 mm (0.00394 to 0.00788 in.)

    1. If the backlash is not as specified, adjust the side bearing preload or repair as necessary.

      HINT:
      Perform the measurements at 3 or more positions around the circumference of the ring gear.



27. INSPECT RUNOUT OF REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


F001237E09
  1. Using a dial indicator, measure the runout of the companion flange vertically and laterally.

    Maximum runout:
    Runout
    Specified Condition
    Vertical runout
    0.09 mm (0.00355 in.)
    Lateral runout
    0.09 mm (0.00355 in.)

    1. If the runout is greater than the maximum, replace the companion flange.



28. STAKE REAR DRIVE PINION NUT


ZK07449E01
  1. Using a chisel and hammer, stake the nut.



29. INSTALL REAR DIFFERENTIAL BEARING ADJUSTING NUT LOCK


C159769
  1. Install 2 new adjusting locks onto the bearing caps with the 2 bolts.

    Torque:
    13 N*m{ 130 kgf*cm , 9 ft.*lbf }

  1. Bend the nut locks.