FRONT DIFFERENTIAL CARRIER ASSEMBLY (for 4WD) > INSTALLATION |
| 1. INSTALL FRONT DIFFERENTIAL CARRIER ASSEMBLY |
![]() |
Install the differential support with the F and G bolts.
Using a jack, slowly raise the front differential carrier assembly to its installation position.
Temporarily install the A, B, C, D and E bolts.
Tighten the A bolt.
Tighten the B and C bolts.
Tighten the D and E bolts.
Connect the automatic disconnecting differential actuator hose.
Connect the automatic disconnecting differential actuator connector.
| 2. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
Install the front drive shaft (Click here).
| 3. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
| 4. INSTALL FRONT PROPELLER SHAFT ASSEMBLY |
Install the front propeller shaft (Click here).
| 5. ADD DIFFERENTIAL OIL |
![]() |
Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.
| Item | Oil type and viscosity |
| Front differential | Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent. |
| Rear differential |
| Specified Condition | |
| 2.00 to 2.10 liters (2.12 to 2.21 US qts., 1.76 to 1.84 Imp. qts.) |
| Engine type | Wheelbase type | Cab type | Drive type | Specified Condition |
| 3UR-FE. 3UR-FBE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 3.45 to 3.55 liters (3.65 to 3.75 US qts., 3.04 to 3.12 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | Regular | 2WD | 3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.) | |
| 4WD | ||||
| Double | 2WD | |||
| 4WD | ||||
| CrewMax | 2WD | 3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.) | ||
| 4WD | 3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.) | |||
| 4180 mm (13 ft. 8.6 in.) | Double | 2WD | 3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.) | |
| 4WD | ||||
| 1GR-FE and 1UR-FE | 3220 mm (10 ft. 6.8 in.) | Regular | 2WD | 4.00 to 4.10 liters (4.23 to 4.33 US qts., 3.52 to 3.60 Imp. qts.) |
| 4WD | ||||
| 3700 mm (12 ft. 1.7 in.) | ALL | 2WD | 4.55 to 4.65 liters (4.81 to 4.91 US qts., 4.01 to 4.09 Imp. qts.) | |
| 4WD | ||||
| 4180 mm (13 ft. 8.6 in.) | 2WD | |||
| 4WD |
for Rear Differential:
Install a new gasket and the filler plug.
for Front Differential:
Using a 10 mm hexagon wrench, install a new gasket and the filler plug.
| 6. INSTALL NO. 1 ENGINE UNDER COVER |
![]() |
Hook the engine under cover to the vehicle body as shown in the illustration.
Install the 3 screws and 5 bolts.
| 7. INSTALL FRONT WHEEL |
Install the front wheels.
| 8. INSPECT AUTOMATIC DISCONNECTING DIFFERENTIAL ACTUATOR |
Inspect the automatic disconnecting differential actuator (Click here).