DTC P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input |
DTC P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0107 | The manifold absolute pressure sensor voltage is below 0.5 V for 0.5 seconds. (1 trip detection logic) |
|
| P0108 | The manifold absolute pressure sensor voltage is higher than 4.5 V for 0.5 seconds. (1 trip detection logic) |
|
| MAP | Malfunction |
| Approximately 0 kPa |
|
| 130 kPa or higher |
|
| Related DTCs | P0107: Manifold Absolute Pressure (MAP) sensor range check (Low voltage) P0108: Manifold Absolute Pressure (MAP) sensor range check (High voltage) |
| Required Sensors/Components (Main) | Manifold absolute pressure sensor |
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Continuous |
| Duration | 0.5 seconds |
| MIL Operation | Immediate |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs not present | None |
| Starter | Off |
| Time after starter ON to OFF | 2 seconds or more |
| MAP sensor voltage | Below 0.5 V |
| MAP sensor voltage | Higher than 4.5 V |

| Tester Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING TECHSTREAM (MANIFOLD ABSOLUTE PRESSURE) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / MAP.
Read the MAP value.
|
| ||||
| OK | ||
| ||
| 2.CHECK MANIFOLD ABSOLUTE PRESSURE SENSOR (TERMINAL VOLTAGE) |
![]() |
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| D80-3 (VC) - D80-2 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| D80-1 (PIM) - D80-2 (E2) | Ignition switch ON | 3.0 to 5.0 V |
|
| ||||
| OK | |
| 3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
Replace the manifold absolute pressure sensor (Click here).
| NEXT | |
| 4.CHECK WHETHER DTC OUTPUT RECURS |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and wait for 2 seconds.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC output) | Proceed to |
| No DTC output | A |
| DTC P0107 and/or P0108 output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM) |
![]() |
Disconnect the manifold absolute pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D80-1 (PIM) - D74-97 (PIM) | Always | Below 1 Ω |
| D80-3 (VC) - D74-66 (VCV2) | Always | Below 1 Ω |
| D80-2 (E2) - D74-98 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| D80-1 (PIM) or D74-97 (PIM) - Body ground | Always | 10 kΩ or higher |
| D80-3 (VC) or D74-66 (VCV2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||