Home › TRANSMISSION ยท AB60F AUTOMATIC TRANSMISSION › AUTOMATIC TRANSMISSION ASSEMBLY

AUTOMATIC TRANSMISSION ASSEMBLY > INSTALLATION

for Preparation Click here



1. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY


C203634E01
  1. Using a vernier caliper and straightedge, measure dimension A between the transmission fitting surface of the engine *1 and the converter fitting surface of the drive plate *2. (#)



    C150409E01
  1. Aligning the matchmarks on the transmission case and torque converter, and then engage the splines of the input shaft and turbine runner.



    C150410E01
  1. Engage the splines of the stator shaft and stator while turning the torque converter.

    HINT:
    Turn the torque converter approximately 180°.



    C150411E01
  1. Turn the torque converter and align the matchmarks on the torque converter and transmission case to engage the key of the oil pump drive gear into the slot on the torque converter.

    NOTICE:
    Do not push on the torque converter when aligning the matchmarks.



    C193839E02
  1. Using a vernier caliper and a straightedge, measure dimension B shown in the illustration and check that B is greater than A measured in the first step.

    Standard distance:
    B = A + 1 mm (0.0394 in.) or more



2. INSTALL TRANSMISSION CONTROL CABLE BRACKET
  1. Install the bracket with the 2 bolts.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }



3. INSTALL WIRE HARNESS CLAMP BRACKET
  1. Install the front bracket LH with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Install the rear bracket LH with the bolt.

    Torque:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }

  1. Install the rear engine bracket with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }



4. INSTALL PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY
  1. Install the bracket with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



5. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/o Trailer Towing System)


C161367E01
  1. Coat 4 new O-rings with ATF.

  1. Install the 4 O-rings, transmission oil cooler spacer and transmission oil cooler to the automatic transmission assembly with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



6. INSTALL TRANSMISSION OIL COOLER ASSEMBLY (w/ Trailer Towing System)


C161366E01
  1. Coat 4 new O-rings with ATF.

  1. Install the 4 O-rings, transmission oil thermostat and transmission oil cooler to the automatic transmission assembly with the 3 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }



7. INSTALL AUTOMATIC TRANSMISSION ASSEMBLY


C196694E01
  1. Apply clutch spline grease to the surface of the torque converter centerpiece that contacts the crankshaft.

    Clutch spline grease:
    Toyota Genuine Clutch Spline Grease or equivalent
    Maximum grease amount:
    Approximately 1 g (0.0353 oz.) Centerpiece



    C212462E01
  1. Confirm that the 2 knock pins are on the transaxle contact surface of the engine block before transaxle installation.

  1. Install the transmission with the 10 bolts.

    Torque:
    for 17 mm head bolt A:
    71 N*m{ 724 kgf*cm , 52 ft.*lbf }
    for 14 mm head bolt B:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



8. CONNECT NO. 2 WATER BY-PASS PIPE (w/o Towing Hitch)


C162140E01
  1. Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    Make sure the pinching portion of each clip is facing the direction shown in the illustration.



9. CONNECT NO. 2 WATER BY-PASS PIPE (w/ Towing Hitch)


C162129E01
  1. Connect the 2 oil cooler hoses to the transmission oil cooler.

    NOTICE:
    1. Make sure the pinching portion of each clip is facing the direction shown in the illustration.
    2. Make sure the paint portion of each hose is facing outward.



    C161362E01
  1. Connect the 2 water by-pass hoses with the 2 clips and install the water by-pass pipe with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

    NOTICE:
    Pinching portion of clip shall be directed as shown in the illustration.



10. CONNECT BREATHER PLUG HOSE
  1. Connect the 3 breather plug hoses to the harness clamp bracket.



11. CONNECT WIRE HARNESS AND CONNECTOR


    C161361E02
  1. Connect the park/neutral start switch connector, 2 transmission wire connectors and 2 speed sensor connectors.

    HINT:
    Push up the lever until the claw of the transmission wire connector makes a connection sound.

  1. Connect the harness clamp with the bolt.

    Torque:
    8.2 N*m{ 84 kgf*cm , 73 in.*lbf }

  1. Connect the 3 connector clamps and 7 harness clamps.

  1. Tilt up the automatic transmission.

  1. Connect the ground cable with the bolt.

    Torque:
    5.5 N*m{ 56 kgf*cm , 49 in.*lbf }



12. INSTALL REAR NO. 1 ENGINE MOUNTING INSULATOR
  1. Install the rear engine mounting insulator to the transmission with the 4 bolts.

    Torque:
    40 N*m{ 407 kgf*cm , 30 ft.*lbf }



13. INSTALL NO. 3 FRAME CROSSMEMBER SUB-ASSEMBLY
  1. Install the frame crossmember to the rear engine mounting insulator with the 4 bolts.

    Torque:
    21 N*m{ 214 kgf*cm , 15 ft.*lbf }

  1. Install the frame crossmember with the 4 bolts, 4 washers and 4 nuts.

    Torque:
    110 N*m{ 1122 kgf*cm , 81 ft.*lbf }



14. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT
  1. Turn the crankshaft to gain access to the 6 bolts and install the bolts while holding the crankshaft pulley set bolt with a wrench.

    Torque:
    53 N*m{ 535 kgf*cm , 39 ft.*lbf }

    NOTICE:
    First install the black colored bolt and then the remaining 5 bolts.



15. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY


C162141E01
  1. Connect the control cable with a new clip and the nut.

    Torque:
    13 N*m{ 133 kgf*cm , 10 ft.*lbf }

    NOTICE:
    When connecting the cable to the transmission control shaft lever, make sure the cable's L bracket faces the outside of the vehicle.



16. INSTALL STARTER ASSEMBLY
(Click here)


17. INSTALL PROPELLER SHAFT ASSEMBLY
(Click here)


18. INSTALL FRONT PROPELLER SHAFT ASSEMBLY
(Click here)


19. INSTALL FRONT EXHAUST PIPE ASSEMBLY
  1. for Regular Cab Standard Deck:
    (Click here).

  1. except Regular Cab Standard Deck:
    (Click here).



20. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL


21. ADD AUTOMATIC TRANSMISSION FLUID
(Click here)


22. ADD ENGINE COOLANT
  1. Add engine coolant.
    Standard capacity: 
    Item
    Specified Condition
    w/ Trailer Towing System
    13.0 liters (13.7 US qts, 11.4 Imp. qts)
    w/o Trailer Towing System
    12.1 liters (12.8 US qts, 10.6 Imp. qts)

    NOTICE:
    Do not substitute plain water for engine coolant.

    HINT:
    1. TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).
    2. Please contact your Toyota dealer for further details.



    A151850E05
  1. Slowly pour coolant into the radiator reservoir until it reaches the FULL line.

  1. Install the reservoir cap.

  1. Press the inlet and outlet radiator hoses several times by hand, and then check the coolant level. If the coolant level is low, add coolant.

  1. Install the radiator cap.

  1. Start the engine and warm it up until the thermostat opens.

    HINT:
    The thermostat opening timing can be confirmed by pressing the radiator inlet hose by hand, and checking when the engine coolant starts to flow inside the hose.

  1. Maintain the engine speed at 2000 to 2500 rpm.

    NOTICE:
    1. Make sure that the radiator reservoir still has some coolant in it.
    2. Pay attention to the needle of the water temperature meter. Make sure that the needle does not show an abnormally high temperature.
    3. If there is not enough coolant, the engine may burn out or overheat.
    4. Immediately after starting the engine, if the radiator reservoir does not have any coolant, perform the following: 1) stop the engine, 2) wait until the coolant has cooled down, and 3) add coolant until the coolant is filled to the FULL line.
    5. Run the engine at 2000 rpm until the coolant level has stabilized.

  1. Press the inlet and outlet radiator hoses several times by hand to bleed air.

    CAUTION:
    1. Wear protective gloves.
    2. Be careful as the radiator hoses are hot.
    3. Keep your hands away from the fan.

  1. Stop the engine, and wait until the engine coolant cools down to ambient temperature.

    CAUTION:
    Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.



    A161780E01
  1. Check that the coolant level is between the FULL and LOW lines.
    If the coolant level is below the LOW line, repeat all of the procedures above.
    If the coolant level is above the FULL line, drain coolant so that the coolant level is between the FULL and LOW lines.



23. INSPECT FOR ENGINE COOLANT LEAK


A161766

CAUTION:
Do not remove the radiator cap while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.

  1. Fill the radiator with coolant and attach a radiator cap tester.

  1. Warm up the engine.

  1. Using the radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf/cm2, 17 psi), and check that the pressure does not drop.
    If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and head.



24. ADJUST SHIFT LEVER POSITION
  1. Move the shift lever to the N position.



    C155901E01
  1. Fold back the transmission control cable adjust case cover. Then while sliding the slider toward the cable end side, press the lock piece from the back side to release the lock.



    C155902E01
  1. Check that the adjust case's spring is applying enough tension to the shift control cable. Then press the lock piece to set the lock.

    NOTICE:
    1. Use your hand to push the lock piece. Do not use any tools.
    2. Securely push the lock piece so that the slider's protrusion is above the lock piece.

  1. Return the cover of the adjust case to its original position.

  1. Inspect the operation after the adjustment.



25. INSPECT SHIFT LEVER POSITION
  1. When moving the shift lever from the N position to other positions, check that the lever can be shifted smoothly and accurately to each position and that the position indicator comes on in accordance with the shift lever position.
    If the indicator and shift lever position do not match, carry out the following adjustment procedures.



26. INSPECT FOR EXHAUST GAS LEAK
If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.


27. INSTALL NO. 1 ENGINE UNDER COVER


    A150108
  1. Hook the engine under cover to the vehicle body as shown in the illustration.

  1. Install the 3 screws and 5 bolts.

    Torque:
    for bolt:
    29 N*m{ 296 kgf*cm , 21 ft.*lbf }
    for screw:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }



28. RESET MEMORY
(Click here)