Home › STEERING › POWER STEERING › VANE PUMP (for 1UR-FE)

VANE PUMP (for 1UR-FE) > INSPECTION

for Preparation Click here



1. INSPECT VANE PUMP SHAFT AND BUSH IN VANE PUMP FRONT HOUSING


    C202404E02
  1. Using a micrometer, measure the diameter (a) of the vane pump shaft with vane pump pulley.

  1. Using a caliper gauge, measure the inside diameter (b) of the vane pump front housing.

  1. Subtract (a) from (b) to calculate the oil clearance.

    Maximum clearance:
    0.07 mm (0.00276 in.)

    If it is greater than the maximum, replace the vane pump shaft with vane pump pulley.



2. INSPECT VANE PUMP ROTOR AND VANE PUMP PLATE


  1. Inspect the vane pump rotor groove and vane pump plate clearance.



      R010282E03
    1. Using a feeler gauge, measure the clearance between the side face of the vane pump rotor groove and the vane pump plates.

      Maximum clearance:
      0.03 mm (0.00118 in.)



    2. C220821E01
    3. If the clearance is more than the maximum, replace the vane pump plates, vane pump rotor and vane pump cam ring.

      NOTICE:
      1. Check the marks on the vane pump rotor and vane pump cam ring.
      2. Refer to the following table to select an appropriate combination of vane pump rotor, vane pump cam ring and vane pump plates.

        Combination of vane pump rotor, vane pump cam ring and vane pump plates:

        Vane Pump Rotor Mark
        (Part No.)
        Vane Pump Cam Ring Mark
        (Part No.)
        Vane Pump Plate Part No.
        Vane Pump Plate Length
        0
        (44313-60010)
        0
        (44325-0C160)
        44345-0C010
        18.505 to 18.503 mm
        (0.72854 to 0.72846 in.)
        1
        (44313-60020)
        1
        (44325-0C170)
        44345-0C020
        18.502 to 18.501 mm
        (0.72842 to 0.72838 in.)
        2
        (44313-60030)
        2
        (44325-0C180)
        44345-0C030
        18.500 to 18.499 mm
        (0.72835 to 0.72831 in.)
        3
        (44313-60040)
        3
        (44325-0C190)
        44345-0C040
        18.498 to 18.497 mm
        (0.72827 to 0.72823 in.)
        4
        (44313-60050)
        4
        (44325-0C200)
        44345-0C050
        18.496 to 18.495 mm
        (0.72819 to 0.72815 in.)



  1. Inspect the vane pump plate.



      N000372E01
    1. Using a micrometer, measure the thickness of the vane pump plates.

      Standard thickness:
      1.405 to 1.411 mm (0.05531 to 0.05555 in.)

    2. If the thickness is not within the specified range, replace the vane pump plates.



3. INSPECT TOTAL PRELOAD
  1. Check that the pump rotates smoothly without abnormal noise.

  1. Temporarily install the service bolt.

    Recommended service bolt:
    Thread diameter
    Thread pitch
    Bolt length
    10 mm (0.394 in.)
    1.25 mm (0.0492 in.)
    50 mm (1.97 in.)



    C053369E10
  1. Using a torque wrench, measure the pumps rotating torque.

    Standard rotating torque:
    0.3 N*m (3 kgf*cm, 2 in.*lbf) or less

    If the rotating torque is not as specified, check the vane pump housing oil seal.