Home › BODY ELECTRICAL › PARK ASSIST / MONITORING › ULTRASONIC SENSOR (for Rear Side)

ULTRASONIC SENSOR (for Rear Side) > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent airbag and seat belt pretensioner activation.



3. REMOVE LICENSE PLATE LIGHT ASSEMBLY LH (for Resin Type Bumper)


B166101
  1. Remove the screw.

  1. Detach the claw and remove the license plate light.



4. REMOVE LICENSE PLATE LIGHT ASSEMBLY LH (for Steel Type Bumper)


B166101
  1. Remove the screw.

  1. Detach the claw and remove the license plate light.



5. REMOVE LICENSE PLATE LIGHT ASSEMBLY RH (for Resin Type Bumper)

HINT:
Use the same procedures described for the LH side.



6. REMOVE LICENSE PLATE LIGHT ASSEMBLY RH (for Steel Type Bumper)

HINT:
Use the same procedures described for the LH side.



7. REMOVE REAR BUMPER PAD SUB-ASSEMBLY (for Steel Type Bumper)
  1. Remove the clip.



  1. Detach the 14 clips and remove the rear bumper pad.

    HINT:
    Detach the clips from the backside of the rear bumper.



    B166111



8. REMOVE REAR BUMPER PLATE LH (for Steel Type Bumper)


B166112
  1. Detach the 4 clips and remove the rear bumper plate.

    HINT:
    Detach the clips from the backside of the rear bumper.



9. REMOVE REAR BUMPER PLATE RH (for Steel Type Bumper)

HINT:
Use the same procedures described for the LH side.



10. REMOVE REAR BUMPER COVER (for Resin Type Bumper)


  1. w/ Intuitive Parking Assist System:
    Disconnect the connectors and clamps shown in illustration.


    B166117

  1. Remove the 2 clips and 4 screws.

  1. Remove the 4 bolts and 2 nuts.



  1. Detach the 4 claws and remove the rear bumper cover.


    B166102



11. REMOVE REAR BUMPER BAR (for Steel Type Bumper)


  1. w/ Intuitive Parking Assist System:
    Disconnect the connectors and clamps shown in the illustration.


    B166116

  1. Remove the 4 bolts and 2 bumper bar reinforcements.



  1. Remove the 6 bolts and bumper bar.


    B166113E01



12. REMOVE NO. 1 ULTRASONIC SENSOR


    E146470
  1. While pushing down on the lever with a finger to release the one claw, detach the claw on the other side to remove the ultrasonic sensor.

    HINT:
    The type of claw on the top and bottom of the sensor are different. Observe the claws carefully before removing the sensor.



13. REMOVE NO. 1 ULTRASONIC SENSOR RETAINER


    E146469
  1. Detach the 2 claws and remove the sensor retainer from the rear bumper.



14. REMOVE NO. 2 ULTRASONIC SENSOR


    E146468
  1. While pushing down on the lever with a finger to release the one claw, detach the claw on the other side to remove the ultrasonic sensor.

    HINT:
    The type of claw on the top and bottom of the sensor are different. Observe the claws carefully before removing the sensor.



15. REMOVE NO. 2 ULTRASONIC SENSOR RETAINER


    E146469
  1. Detach the 2 claws and remove the sensor retainer from the rear bumper.