Home › ENGINE ยท 1GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0111    Intake Air Temperature Sensor Gradient Too High

for Preparation Click here


DESCRIPTION

A067628E24
  1. The intake air temperature sensor, mounted on the mass air flow meter, monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor with a resistance that varies according to the temperature of the intake air. When the intake air temperature is low, the resistance of the thermistor increases. When the temperature is high, the resistance drops. These variations in resistance are transmitted to the ECM as voltage changes (See Fig. 1).
  2. The intake air temperature sensor is powered by a 5 V supply from the THA terminal of the ECM, via resistor R.
  3. Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes according to changes in the intake air temperature, the voltage at terminal THA also varies. Based on this signal, the ECM increases the fuel injection volume when the engine is cold to improve driveability.

DTC No.
DTC Detection Condition
Trouble Area
P0111
Either condition is met (2 trip detection logic):
  1. In duration between engine warmed up and next engine start, change in Intake Air Temperature (IAT) sensor output below threshold
  2. During engine warming up after cold engine starts, change in IAT sensor output below threshold
Mass air flow meter

MONITOR DESCRIPTION

The ECM performs OBD II monitoring based on the values from the intake air temperature sensor. If there is no change of the sensor value within the normal range, the ECM will not be able to perform OBD II monitoring or will misdiagnose that there is a malfunction in the sensor. The ECM detects when the intake air temperature sensor value is stuck by performing monitoring after the ignition switch is turned off or the engine is started (short soak or long soak).

MONITOR STRATEGY


Related DTCs
P0111: Intake air temperature sensor rationality (After engine stop)
P0111: Intake air temperature sensor rationality (After cold engine start)
Required Sensors/Components (Main)
Intake air temperature sensor
Required Sensors/Components (Related)
-
Frequency of Operation
Once per driving cycle
Duration
-
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
Monitor runs whenever following DTCs are not stored
P0112, P0113 (Intake Air Temperature Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0102, P0103 (Mass Air Flow Sensor)
P2610 (Soak Timer)

After Engine Stop 
Time after engine start
10 seconds or more
Battery voltage
10.5 V or higher
Engine coolant temperature when ECM started by soak timer
-40°C (-40°F) or higher
Accumulated mass airflow amount before engine stop
3828 g or more
Key-off duration
30 minutes

After Cold Engine Start 
Key-off duration
5 hours
Time after engine start
10 seconds or more
Engine coolant temperature
70°C (158°F) or higher
Accumulated mass airflow amount
3828 g or more
Either of the following conditions is met:
-
1. Duration while engine load is low
120 seconds or more
2. Duration while engine load is high
10 seconds or more

TYPICAL MALFUNCTION THRESHOLDS


After Engine Stop 
Intake air temperature change
Less than 1°C (1.8°F)

After Cold Engine Start 
Intake air temperature change
Less than 1°C (1.8°F)

CONFIRMATION DRIVING PATTERN


A198822E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].
  7. Idle the engine for 5 minutes or more [C].

    HINT:
    During steps [A] through [C], if the change in the intake air temperature is less than 1°C (1.8°F), the intake air temperature sensor (mass air flow meter) is malfunctioning. It is not necessary to continue this procedure.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0111.
  12. Check the DTC judgment result.

    Techstream Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. If the judgment result shows ABNORMAL, the system has a malfunction.
    2. If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F].

  13. Drive the vehicle at 40 km/h (25 mph) or more for a total of 5 minutes or more [E].
  14. Check the DTC judgment result again [F].

    HINT:
    If the judgment result shows INCOMPLETE or N/A, perform steps [E] and [F] again.

  15. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


INSPECTION PROCEDURE

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0111)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result 
    Result
    Proceed to
    P0111 and other DTCs are output
    A
    P0111 is output
    B

    HINT:
    1. If any DTCs other than P0111 are output, troubleshoot those DTCs first.
    2. Perform "Inspection After Repair" after replacing the mass air flow meter (Click here).



B
REPLACE MASS AIR FLOW METER (Click here)
A

GO TO DTC CHART (Click here)