REAR VIEW MONITOR SYSTEM (w/ Navigation System) > Display Signal Circuit between Navigation Receiver Assembly and Television Camera Assembly |


| 1.CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER - TELEVISION CAMERA) |
for DVD Navigation System:
Disconnect the K7 navigation receiver assembly connector.
Disconnect the X1 television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K7-22 (V+) - X1-1 (CV+) | Always | Below 1 Ω |
| K7-23 (V-) - X1-2 (CV-) | Always | Below 1 Ω |
| K7-21 (CGND) - X1-4 (CGND) | Always | Below 1 Ω |
| K7-24 (CA+) - X1-3 (CB+) | Always | Below 1 Ω |
| K7-22 (V+) - Body ground | Always | 10 kΩ or higher |
| K7-23 (V-) - Body ground | Always | 10 kΩ or higher |
| K7-21 (CGND) - Body ground | Always | 10 kΩ or higher |
| K7-24 (CA+) - Body ground | Always | 10 kΩ or higher |
for SD Navigation System:
Disconnect the K23 navigation receiver assembly connector.
Disconnect the X1 television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K23-11 (V+) - X1-1 (CV+) | Always | Below 1 Ω |
| K23-12 (V-) - X1-2 (CV-) | Always | Below 1 Ω |
| K23-14 (CGND) - X1-4 (CGND) | Always | Below 1 Ω |
| K23-13 (CA+) - X1-3 (CB+) | Always | Below 1 Ω |
| K23-11 (V+) - Body ground | Always | 10 kΩ or higher |
| K23-12 (V-) - Body ground | Always | 10 kΩ or higher |
| K23-14 (CGND) - Body ground | Always | 10 kΩ or higher |
| K23-13 (CA+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 2.CHECK NAVIGATION RECEIVER ASSEMBLY |
![]() |
for DVD Navigation System:
Disconnect the K7 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K7-21 (CGND) - Body ground | Always | Below 1 Ω |
| K7-23 (V-) - Body ground | Always | Below 1 Ω |
![]() |
for SD Navigation System:
Disconnect the K23 navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K23-12 (V-) - Body ground | Always | Below 1 Ω |
| K23-14 (CGND) - Body ground | Always | Below 1 Ω |
| *a | Component without harness connected (Navigation Receiver Assembly) |
| Result | Proceed to |
| OK | A |
| NG (for Column Shift Type) | B |
| NG (for Floor Shift Type) | C |
|
| ||||
|
| ||||
| A | |
| 3.CHECK NAVIGATION RECEIVER ASSEMBLY |
![]() |
Disconnect the X1 television camera assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| X1-3 (CB+) - X1-4 (CGND) | Ignition switch ON, shift lever in R | 5.5 to 7.05 V |
| *a | Front view of wire harness connector (to Television Camera Assembly) |
| Result | Proceed to |
| OK | A |
| NG (for Column Shift Type) | B |
| NG (for Floor Shift Type) | C |
|
| ||||
|
| ||||
| A | |
| 4.CHECK TELEVISION CAMERA ASSEMBLY |
for DVD Navigation System:
Using an oscilloscope, check the waveform.

| *a | Component with harness connected (Navigation Receiver Assembly) | *b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronized Signal |
| *e | Video Waveform | - | - |
| Item | Content |
| Terminal No. (Symbol) | K7-22 (V+) - K7-23 (V-) |
| Tool Setting | 0.2 V/DIV., 50 μs/DIV. |
| Condition |
|
for SD Navigation System:
Using an oscilloscope, check the waveform.

| *a | Component with harness connected (Navigation Receiver Assembly) | *b | Waveform 1 |
| *c | Waveform 2 | *d | Synchronized Signal |
| *e | Video Waveform | - | - |
| Item | Content |
| Terminal No. (Symbol) | K23-11 (V+) - K23-12 (V-) |
| Tool Setting | 0.2 V/DIV., 50 μs/DIV. |
| Condition |
|
|
| ||||
| OK | ||
| ||