Home › DRIVE LINE › DIFFERENTIAL › FRONT DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL (for 4WD)

FRONT DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL (for 4WD) > REPLACEMENT

for Preparation Click here


HINT:
The procedure described below is for the LH side. Use the same procedure for both the RH and LH sides, unless otherwise specified.



1. DRAIN DIFFERENTIAL OIL
  1. Stop the vehicle on a level place.

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, remove the filler plug and gasket.

    2. Using a 10 mm hexagon wrench, remove the drain plug and gasket, and drain the oil.

    3. Using a 10 mm hexagon wrench, install a new gasket and the drain plug.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }

  1. for Rear Differential:

    1. Remove the filler plug and gasket.

    2. Remove the drain plug and gasket, and drain the oil.

    3. Install a new gasket and the drain plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }



2. REMOVE FRONT DRIVE SHAFT ASSEMBLY LH
  1. Remove the front drive shaft (Click here).



3. REMOVE DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


C097017E03
  1. Using SST, tap out the 2 oil seals.

    SST
    09308-10010  



4. INSTALL DIFFERENTIAL SIDE GEAR SHAFT OIL SEAL


B084278E02
  1. Apply MP grease to 2 new oil seals.

  1. Using SST and a hammer, tap in the 2 oil seals.

    SST
    09550-00032  
    09950-70010   (09951-07100)

    NOTICE:
    Make sure the LH and RH oil seals are installed in the proper locations.

    Standard oil seal depth:
    Side
    Specified Condition
    LH
    -0.45 to 0.45 mm (-0.0177 to 0.0177 in.)
    RH
    4.8 to 5.8 mm (0.189 to 0.228 in.)



5. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH
  1. Install the front drive shaft (Click here).



6. ADD DIFFERENTIAL OIL


    D025304E27
  1. Add differential oil so that the oil level is between 0 to 5 mm (0 to 0.197 in.) from the bottom lip of the differential filler plug hole.

    NOTICE:
    1. Too much or too little oil will lead to differential problems.
    2. After changing the oil, drive the vehicle and then check the oil level again.

    Oil type:
    Item
    Oil type and viscosity
    Front differential
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent.
    Rear differential

    Front differential capacity:
    Specified Condition
    2.00 to 2.10 liters (2.12 to 2.21 US qts., 1.76 to 1.84 Imp. qts.)


    Rear differential capacity:

    Engine type
    Wheelbase type
    Cab type
    Drive type
    Specified Condition
    3UR-FE. 3UR-FBE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    3.45 to 3.55 liters (3.65 to 3.75 US qts., 3.04 to 3.12 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    Regular
    2WD
    3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.)
    4WD
    Double
    2WD
    4WD
    CrewMax
    2WD
    3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.)
    4WD
    3.55 to 3.65 liters (3.76 to 3.85 US qts., 3.13 to 3.21 Imp. qts.)
    4180 mm (13 ft. 8.6 in.)
    Double
    2WD
    3.70 to 3.80 liters (3.91 to 4.01 US qts., 3.26 to 3.34 Imp. qts.)
    4WD
    1GR-FE and 1UR-FE
    3220 mm (10 ft. 6.8 in.)
    Regular
    2WD
    4.00 to 4.10 liters (4.23 to 4.33 US qts., 3.52 to 3.60 Imp. qts.)
    4WD
    3700 mm (12 ft. 1.7 in.)
    ALL
    2WD
    4.55 to 4.65 liters (4.81 to 4.91 US qts., 4.01 to 4.09 Imp. qts.)
    4WD
    4180 mm (13 ft. 8.6 in.)
    2WD
    4WD

  1. for Rear Differential:

    1. Install a new gasket and the filler plug.

      Torque:
      49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. for Front Differential:

    1. Using a 10 mm hexagon wrench, install a new gasket and the filler plug.

      Torque:
      39 N*m{ 398 kgf*cm , 29 ft.*lbf }