Home › ENGINE ยท 3UR-FBE › FUEL › FUEL SYSTEM

FUEL SYSTEM > PRECAUTION

for Preparation Click here


CAUTION:
  1. Before working on the fuel system, disconnect the cable from the negative (-) battery terminal.
  2. Do not smoke or be near an open flame when working on the fuel system.
  3. Keep gasoline away from rubber and leather parts.

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


1.DISCHARGE FUEL SYSTEM PRESSURE

CAUTION:
  1. Do not disconnect any part of the fuel system until you have discharged the fuel system pressure.
  2. After discharging the fuel pressure, place a cloth or equivalent over fittings as you separate them to reduce the risk of fuel spray on yourself or in the engine compartment.

  1. Disconnect the cable from the negative (-) battery terminal.



  2. A194647
  3. Disconnect the 2 fuel pump ECU connectors.

  4. Connect the cable to the negative (-) battery terminal.

  5. Start the engine. After the engine has stopped on its own, turn the ignition switch off.

    HINT:
    DTC P0171/0174 (system too lean) may be stored.

  6. Crank the engine again, and check that the engine does not start.

  7. Loosen the fuel tank cap, then discharge the pressure in the fuel tank completely.

  8. Connect the 2 fuel pump ECU connectors.


2.FUEL SYSTEM


  1. When disconnecting the high fuel pressure line, a large amount of gasoline will spill out. Follow these procedures.

    1. Perform the "DISCHARGE FUEL SYSTEM PRESSURE" procedures above.



    2. A133694
    3. Put a container under the connecting part of the pressure line.

    4. Slowly loosen the connection.

    5. Disconnect the connection.

    6. Plug the connection with a rubber plug.



  2. A163532E01
  3. Observe these precautions when removing and installing the injectors:

    1. Never reuse the O-ring.
    2. When installing a new O-ring to the injector, do not damage it.
    3. Coat a new O-ring with spindle oil or gasoline before installing it. Do not use engine oil, gear oil or brake oil.



  4. A163533E01
  5. Install the injector to the delivery pipe and cylinder head as shown in the illustration.

    NOTICE:
    Before installing the injector, apply spindle oil or gasoline to the surface where the delivery pipe contacts the O-ring of the injector.



  6. Observe these precautions when disconnecting the fuel tube connector (for quick type).



      A157617E01
    1. for Fuel Hose Connector Cover Type:
      Detach the lock claws by lifting up the cover, as shown in the illustration.



    2. C157056E01
    3. for Fuel Pipe Clamp Type:
      Remove the fuel pipe clamp from the fuel tube connector.

    4. Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.



    5. A088336E04
    6. Pinch the connector and disconnect the connector and pipe.
      If the connector and the pipe are stuck together, pinch the connector, push and pull the pipe to disconnect the pipe.

      NOTICE:
      Do not use any tools.

    7. Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.



    8. A099427E05
    9. To protect the disconnected pipe and connector from damage and contamination, cover them with plastic bags.



  7. A130944E01
  8. Observe these precautions when connecting the fuel tube connector (for quick type).

    1. Check that there is no damage or contamination in the connected part of the pipe.

    2. Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh spindle oil or gasoline on the tip of the pipe.



    3. A130945E02
    4. After connecting the pipe and connector, try to pull apart the pipe and the connector to confirm that they are securely connected.



    5. C157056E01
    6. for Fuel Pipe Clamp Type:
      Install the fuel pipe clamp to the connector.



    7. A157616E01
    8. for Fuel Hose Connector Cover Type:
      Attach the lock claws to the connector by pushing down on the cover, as shown in the illustration.

    9. Check that there is no fuel leakage.


3.CHECK FOR FUEL LEAK
  1. Check that there are no fuel leaks after performing maintenance anywhere on the fuel system .