FUEL SYSTEM > PRECAUTION |
| 1.DISCHARGE FUEL SYSTEM PRESSURE |
Disconnect the cable from the negative (-) battery terminal.
Disconnect the fuel pump ECU connector .
Connect the cable to the negative (-) battery terminal.
Start the engine. After the engine has stopped on its own, turn the ignition switch off.
Crank the engine again and check that the engine does not start.
Loosen the fuel tank cap to discharge the pressure in the fuel tank completely.
Connect the fuel pump ECU connector .
| 2.FUEL SYSTEM |
When disconnecting a high pressure fuel line, a large amount of gasoline will spill out. Follow these procedures.
Disconnect the fuel pump tube.
Drain any fuel remaining inside the fuel pump tube.
To protect the disconnected fuel pump tube from damage and contamination, cover it with a plastic bag.
Put a container under the connection.
![]() |
Observe these precautions when removing and installing the injectors.
| *a | OK |
| *b | NG |
Never reuse the O-ring.
When installing a new O-ring to the injector, do not damage it.
Coat new O-rings with spindle oil or gasoline before installing them. Do not use engine oil, gear oil or brake oil.
![]() |
Install the injector to the delivery pipe and lower intake manifold as shown in the illustration.
| *1 | O-Ring |
Observe these precautions when disconnecting the fuel tube connector (for quick type).
![]() |
For fuel pipe clamp type:
| *1 | Fuel Pipe Clamp |
![]() |
For fuel hose connector cover type:
| *1 | Fuel Hose Connector Cover |
Check for dirt or mud on the pipe and around the connector before disconnection. Clean if necessary.
![]() |
If the connector and pipe are stuck together, pinch the connector, and then push and pull the pipe to disconnect the pipe and pull it out.
| *1 | Retainer |
![]() | Pinch |
![]() | Pull |
![]() |
| *1 | Retainer |
| *2 | Nylon Tube |
| *3 | Pipe |
| *4 | O-Ring |
| *5 | Fuel Tube Connector |
Check for dirt or mud on the seal surface of the disconnected pipe. Clean if necessary.
To protect the disconnected pipe and connector from damage and contamination, cover them with a plastic bag.
![]() |
Observe these precautions when connecting the fuel tube connector (for quick type).
Check that there is no damage or contamination in the connecting part of the pipe.
Align the axis of the connector with the axis of the pipe. Push the pipe into the connector until the connector makes a "click" sound. If the connection is tight, apply a small amount of fresh engine oil to the tip of the pipe.
![]() | Push |
![]() |
After connecting the pipe and connector, check that they are securely connected by trying to pull them apart.
![]() | Pull |
For fuel hose connector cover type:
Attach the lock claws to the connector by pushing down on the cover.
For fuel pipe clamp type:
Install the fuel pipe clamp to the connector.
Check for any fuel leaks.
![]() |
Observe these precautions when disconnecting the fuel tank breather tube connector.
| *1 | Fuel Tank Breather Tube Connector |
| *2 | Pipe |
![]() | Push |
![]() | Pinch |
Pinch the retainer and pull out the fuel tank breather tube connector with the fuel tank breather tube connector pushed toward the pipe to disconnect the fuel tank breather tube from the pipe.
![]() |
| *1 | Fuel Tank Breather Tube Connector |
| *2 | Pipe |
| *3 | Nylon Tube |
| *4 | O-Ring |
![]() |
Observe these precautions when connecting the fuel tank breather tube connector.
Align the fuel tank breather tube connector with the pipe, and then push in the fuel tank breather tube connector until the retainer makes a "click" sound to connect the fuel tank breather tube to the pipe.
![]() | Push |
![]() |
After connecting the pipe and the connector, check that they are securely connected by trying to pull them apart.
![]() | Pull |
Check for any fuel leaks.
| 3.INSPECT FOR FUEL LEAK |