Home › ENGINE ยท 1GR-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > INSPECTION

for Preparation Click here



1. INSPECT CYLINDER HEAD SET BOLT


A224657E01
  1. Using a vernier caliper, measure the length of the cylinder head set bolt from the seat to the end.
    Text in Illustration 
    *a
    Measurement Length

    Standard length:
    141.3 to 142.7 mm (5.56 to 5.62 in.)

    Maximum length:
    143.7 mm (5.66 in.)

    If the length is more than the maximum, replace the cylinder head set bolt.



    A226002
  1. Using a vernier caliper, measure the diameter of the elongated thread at the narrowest visible area.

    Standard diameter:
    10.73 to 10.97 mm (0.422 to 0.432 in.)

    Minimum diameter:
    10.70 mm (0.421 in.)

    If the diameter is less than the minimum, replace the cylinder head set bolt.

    HINT:
    If a visual check reveals no excessively thin areas, check the center of the bolt (refer to illustration) and find the area that has the smallest diameter.



2. INSPECT NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY
  1. Turn the roller by hand to check that it turns smoothly.
    If the roller does not turn smoothly, replace the No. 1 valve rocker arm sub-assembly.



3. INSPECT VALVE LASH ADJUSTER ASSEMBLY

NOTICE:
  1. Keep the lash adjuster free from dirt and foreign objects.
  2. Only use clean engine oil.



    A101354E03
  1. Place the lash adjuster into a container full of new engine oil.
    Text in Illustration 
    *1
    Taper Part
    *2
    Plunger
    *3
    Low Pressure Chamber
    *4
    Check Ball
    *5
    High Pressure Chamber
    *a
    CORRECT
    *b
    INCORRECT

  1. Insert the tip of SST into the lash adjuster plunger and use the tip to press down on the check ball inside the plunger.

    SST
    09276-75010  

  1. Squeeze SST and the lash adjuster together to move the plunger up and down 5 to 6 times.

  1. Check the movement of the plunger and bleed air.

    OK:
    Plunger moves up and down.

    NOTICE:
    When bleeding high-pressure air from the compression chamber, make sure that the tip of SST is actually pressing the check ball as shown in the illustration. If the check ball is not pressed, air will not bleed.

  1. After bleeding the air, remove SST. Then try to quickly and firmly press the plunger with your fingers.

    OK:
    Plunger can be pressed 3 times.

    If the plunger can still be compressed after pressing it 3 times, replace the valve lash adjuster with a new one.



4. INSPECT CAMSHAFT
  1. Inspect the camshaft runout.

    1. Place the camshaft on V-blocks.

    2. Using a dial indicator, measure the circle runout at the center journal.

      Maximum runout:
      0.04 mm (0.00157 in.)

      If the runout is more than the maximum, replace the camshaft.

      HINT:
      Check the oil clearance after replacing the camshaft.

  1. Using a micrometer, measure the cam lobe height.

    Standard Cam Lobe Height:
    Item
    Specified Condition
    Intake camshaft
    43.890 to 43.990 mm (1.728 to 1.732 in.)
    Exhaust camshaft
    44.262 to 44.362 mm (1.743 to 1.747 in.)

    Minimum Cam Lobe Height:
    Item
    Specified Condition
    Intake camshaft
    43.840 mm (1.726 in.)
    Exhaust camshaft
    44.212 mm (1.741 in.)

  1. Using a micrometer, measure the journal diameter.

    Standard Journal Diameter:
    Item
    Specified Condition
    No. 1 journal
    35.946 to 35.960 mm (1.4152 to 1.4157 in.)
    Other journals
    25.959 to 25.975 mm (1.0221 to 1.0226 in.)

    If the journal diameter is not as specified, check the oil clearance.



5. INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.



    A229667E01
  1. Put the camshaft timing gear assembly and camshaft together by aligning the pin hole and straight pin.
    Text in Illustration 
    *1
    Pin Hole
    *2
    Straight Pin

  1. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

    NOTICE:
    Be sure not to turn the camshaft timing gear assembly in the retard direction.

  1. Check that there is no clearance between the camshaft timing gear assembly flange and camshaft.



    A229666
  1. Tighten the flange bolt while holding the camshaft.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Check the lock of the camshaft timing gear assembly.

    1. Fix the camshaft in place and confirm that the camshaft timing gear assembly is locked.

      NOTICE:
      Be careful not to damage the camshaft.



    A229672E01
  1. Release the lock pin.

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Open
      *4
      Close
      V100144
      Rubber
      V100145
      Vinyl Tape

      HINT:
      The 2 advance side paths are located in the camshaft groove. Plug one of the paths with a rubber piece.

    2. Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path, as shown in the illustration.



    3. A229673E01
    4. Apply air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path

      CAUTION:
      Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



    5. A229674E01
    6. Check that the camshaft timing gear assembly rotates in the advance direction when reducing the air pressure applied to the retard side path.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Hold Pressure
      *4
      Decompress

      HINT:
      This operation releases the lock pin at the most retarded position.

    7. When the camshaft timing gear assembly reaches the most advanced position, release the air pressure first from the retard side path and next from the advance side path.

      NOTICE:
      Do not release the air pressure from the advance side path first. The gear may abruptly shift in the retard direction and break the lock pin.

  1. Check for smooth rotation.

    1. Turn the camshaft timing gear assembly within its movable range (21°) 2 or 3 times, but do not turn it to the most retarded position. Make sure that the gear turns smoothly.

      NOTICE:
      Do not use air pressure to perform the smooth operation check.

  1. Check the lock in the most retarded position.

    1. Confirm that the camshaft timing gear assembly locks at the most retarded position.



    A227959E01
  1. Remove the flange bolt and camshaft timing gear assembly.
    Text in Illustration 
    *1
    Do not remove
    *2
    Straight Pin
    *3
    Flange Bolt

    NOTICE:
    1. Do not remove the other 3 bolts.
    2. If planning to reuse the camshaft timing gear, be sure to release the straight pin lock before installing the camshaft timing gear.



6. INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Fix the camshaft in place.

    NOTICE:
    Be careful not to damage the camshaft.



    A227956E01
  1. Put the camshaft timing exhaust gear assembly and camshaft together by aligning the pin hole and straight pin.
    Text in Illustration 
    *1
    Pin Hole
    *2
    Straight Pin

  1. Lightly press and turn the camshaft timing gear assembly against the camshaft, and press harder after the pin enters the hole.

    NOTICE:
    Be sure not to turn the camshaft timing exhaust gear in the advanced direction.

  1. Check that there is no clearance between the gear flange and camshaft.



    A229668
  1. Tighten the flange bolt while holding the camshaft.

    Torque:
    100 N*m{ 1020 kgf*cm , 74 ft.*lbf }

  1. Check the camshaft timing exhaust gear lock.

    1. Make sure that the camshaft timing exhaust gear assembly locks.



    A229675E01
  1. Release the lock pin.

    1. Cover the 4 oil paths of the cam journal with vinyl tape as shown in the illustration.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Open
      *4
      Close
      V100144
      Rubber
      V100145
      Vinyl Tape

      HINT:
      The 2 advance side paths are located in the camshaft groove. Plug one of the paths with a rubber piece.

    2. Break through the tape on the advance side path and the retard side path on the opposite side of the hole of the advance side path, as shown in the illustration.



    3. A229676E01
    4. Apply air at approximately 200 kPa (2.0 kgf/cm2, 28 psi) to the 2 open paths (the advance side path and retard side path).
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path

      CAUTION:
      Cover the paths with a piece of cloth when applying pressure to prevent oil from spraying.



    5. A229677E01
    6. Make sure that the camshaft timing exhaust gear assembly rotates in the retard direction when reducing the air pressure applied to the advance side path.
      Text in Illustration 
      *1
      Advance Side Path
      *2
      Retard Side Path
      *3
      Hold Pressure
      *4
      Decompress

      HINT:
      The lock pin is released and the camshaft timing exhaust gear assembly turns in the retard direction.

    7. When the camshaft timing exhaust gear assembly moves to the most retarded position, release the air pressure first from the advance side path, and then release the air pressure from the retard side path.

      NOTICE:
      Be sure to release the air pressure from the advance side path first. If the air pressure of the retard side path is released first, the camshaft timing exhaust gear assembly may abruptly shift in the advance direction and break the lock pin or other parts.

  1. Check for smooth rotation.

    1. Turn the camshaft timing exhaust gear assembly within its movable range (18.5°) 2 or 3 times, but do not turn it to the most advanced position. Make sure that the gear assembly turns smoothly.

      NOTICE:
      When the air pressure is released from the advance side path and then from the retard side path, the gear assembly automatically returns to the most advanced position due to the advance assist spring operation and locks. Gradually release the air pressure from the retard side path before performing the smooth rotation check.

  1. Check the lock at the most advanced position.

    1. Make sure that the camshaft timing exhaust gear assembly locks at the most advanced position.



    A227960E01
  1. Remove the flange bolt and camshaft timing exhaust gear assembly.
    Text in Illustration 
    *1
    Do not remove
    *2
    Straight Pin
    *3
    Flange Bolt

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.



7. INSPECT NO. 1 CHAIN SUB-ASSEMBLY


    A139523E07
  1. Using a spring scale, pull the No. 1 chain with a force of 147 N (15 kgf, 33 lbf) and measure the length of the No. 1 chain using a vernier caliper.

    Maximum chain elongation:
    136.9 mm (5.39 in.)

    Text in Illustration 
    *a
    Measurement Area

    HINT:
    Perform the measurement at 3 random places.

    If a measurement is more than the maximum, replace the No. 1 chain.



8. INSPECT NO. 2 CHAIN SUB-ASSEMBLY
  1. Using a spring scale, pull the No. 2 chain with a force of 147 N (15 kgf, 33 lbf) and measure the length of the No. 2 chain using a vernier caliper.

    Maximum chain elongation:
    137.6 mm (5.42 in.)

    HINT:
    Perform the measurement at 3 random places.

    If a measurement is more than the maximum, replace the No. 2 chain.



9. INSPECT CRANKSHAFT TIMING SPROCKET


    A131945
  1. Wrap the No. 1 chain around the sprocket.

  1. Using a vernier caliper, measure the crankshaft timing sprocket diameter with the No. 1 chain.

    Minimum gear diameter (with chain):
    61.0 mm (2.40 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the No. 1 chain and crankshaft timing sprocket.



10. INSPECT NO. 1 IDLE GEAR


    A131946
  1. Wrap the No. 1 chain around the gear.

  1. Using a vernier caliper, measure the No. 1 idle gear diameter with the No. 1 chain.

    Minimum gear diameter (with chain):
    61.0 mm (2.40 in.)

    HINT:
    The vernier caliper must contact the chain rollers for the measurement.

    If the diameter is less than the minimum, replace the No. 1 chain and No. 1 idle gear.



11. INSPECT NO. 1 IDLE GEAR SHAFT OIL CLEARANCE
  1. Using a micrometer, measure the No. 1 idle gear shaft diameter.

    Standard idle gear shaft diameter:
    22.987 to 23.000 mm (0.905 to 0.906 in.)

  1. Using a caliper gauge, measure the inside diameter of the idle gear.

    Standard idle gear inside diameter:
    23.02 to 23.03 mm (0.906 to 0.907 in.)

  1. Subtract the idle gear shaft diameter measurement from the idle gear inside diameter measurement.

    Standard oil clearance:
    0.020 to 0.043 mm (0.000787 to 0.00169 in.)

    Maximum oil clearance:
    0.093 mm (0.00366 in.)

    If the shaft oil clearance is more than the maximum, replace the idle gear shaft and idle gear.



12. INSPECT NO. 1 CHAIN TENSIONER ASSEMBLY


    A120674E03
  1. Move the stopper plate upward to release the lock. Push the plunger and check that it moves smoothly.
    Text in Illustration 
    *1
    Plunger
    *2
    Stopper Plate
    *a
    Moves Smoothly
    If necessary, replace the No. 1 chain tensioner.



13. INSPECT NO. 2 CHAIN TENSIONER ASSEMBLY


    A131966E03
  1. Check that the plunger moves smoothly.
    Text in Illustration 
    *a
    Depth
    *b
    Moves Smoothly

  1. Measure the depth of wear of the chain tensioner.

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the No. 2 chain tensioner.



14. INSPECT NO. 3 CHAIN TENSIONER ASSEMBLY


    A131967E03
  1. Check that the plunger moves smoothly.
    Text in Illustration 
    *a
    Depth
    *b
    Moves Smoothly

  1. Measure the depth of wear of the chain tensioner.

    Maximum depth:
    1.0 mm (0.0394 in.)

    If the depth is more than the maximum, replace the No. 3 chain tensioner.



15. INSPECT CHAIN TENSIONER SLIPPER


    A222118E01
  1. Measure the depth of wear of the chain tensioner slipper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *a
    Depth
    If the depth is more than the maximum, replace the chain tensioner slipper.



16. INSPECT NO. 1 CHAIN VIBRATION DAMPER


    A222119E01
  1. Measure the depth of wear of the No. 1 chain vibration damper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *a
    Depth
    If the depth is more than the maximum, replace the No. 1 chain vibration damper.



17. INSPECT NO. 2 CHAIN VIBRATION DAMPER


    A222120E01
  1. Measure the depth of wear of the No. 2 chain vibration damper.

    Maximum depth:
    1.0 mm (0.0394 in.)

    Text in Illustration 
    *a
    Depth
    If the depth is more than the maximum, replace the No. 2 chain vibration damper.



18. INSPECT CAMSHAFT THRUST CLEARANCE


    A223707
  1. Install the camshafts .

  1. Using a dial indicator, measure the thrust clearance while moving the camshaft back and forth.

    Standard thrust clearance:
    0.08 to 0.13 mm (0.00315 to 0.00512 in.)

    Maximum thrust clearance:
    0.15 mm (0.00591 in.)

    If the thrust clearance is more than the maximum, replace the camshaft housing. If the thrust surface is damaged, replace the camshaft.

  1. Perform the inspection above for each camshaft.



19. INSPECT CAMSHAFT OIL CLEARANCE
  1. Clean the camshaft bearing caps, camshaft housing and camshaft journals.

  1. Place the camshafts on the camshaft housing.



    A120715E04
  1. Lay a strip of Plastigage across each camshaft journal.
    Text in Illustration 
    *1
    Plastigage

  1. Install the camshaft bearing caps .

    NOTICE:
    Do not turn the camshaft.

  1. Remove the camshaft bearing caps .



    A221389E01
  1. Measure the Plastigage at its widest point.

    Standard Oil Clearance:
    Item
    Specified Condition
    No. 1 journal
    0.032 to 0.063 mm (0.00126 to 0.00248 in.)
    Other journals
    0.025 to 0.062 mm (0.000984 to 0.00244 in.)

    Maximum Oil Clearance:
    Item
    Specified Condition
    No. 1 journal
    0.10 mm (0.00394 in.)
    Other journals
    0.09 mm (0.00354 in.)

    Text in Illustration 
    *1
    Plastigage
    *2
    No. 1 Journal
    *3
    Other Journals
    If the oil clearance is more than the maximum, replace the camshaft. If necessary, replace the camshaft housing.



20. INSPECT EXHAUST MANIFOLD SUB-ASSEMBLY


    A222170
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surface which contacts the cylinder head.

    Maximum warpage:
    0.70 mm (0.0276 in.)

    If the warpage is more than the maximum, replace the exhaust manifold.



21. INSPECT INTAKE MANIFOLD FOR FLATNESS


    A222115E01
  1. Using a precision straightedge and feeler gauge, measure the warpage of the surfaces which contact the cylinder head and intake air surge tank.

    Maximum Warpage:
    Item
    Specified Condition
    Intake air surge tank side
    0.80 mm (0.0315 in.)
    Cylinder head side
    0.20 mm (0.00787 in.)

    Text in Illustration 
    *A
    Intake Air Surge Tank Side
    *B
    Cylinder Head Side
    If the warpage is more than the maximum, replace the intake manifold.