Home › ENGINE · 1GR-FE › STARTING › STARTER (for 1.6 kW Type)

STARTER (for 1.6 kW Type) > INSPECTION

for Preparation Click here


CAUTION:
As a large electric current passes through the cable during this inspection, a thick cable must be used. If not, the cable may become hot and cause injury.

NOTICE:
The following tests must each be performed within 3 to 5 seconds to prevent the coil from burning out.



1. INSPECT STARTER ASSEMBLY


  1. Perform a pull-in test.

    1. Remove the nut and disconnect the lead wire from terminal C.



    2. A075962E03
    3. Connect the battery to the starter as shown in the illustration. Then check that the clutch pinion gear moves outward.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      If the result is not as specified, replace the repair service starter kit.



  1. Perform holding test.



      A075963E03
    1. With the battery connected as above with the clutch pinion gear out, disconnect the negative (-) terminal lead from terminal C. Check that the pinion gear remains out.
      Text in Illustration 
      *1
      Terminal C
      V100135
      Disconnect
      If the result is not as specified, replace the repair service starter kit.



    2. A075964E03
    3. Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear returns inward.
      Text in Illustration 
      *1
      Terminal 50
      V100135
      Disconnect
      If the result is not as specified, replace the repair service starter kit.



  1. Perform an operation test without load.

    1. Connect the lead wire to terminal C.

      Torque:
      10 N*m{ 102 kgf*cm , 7 ft.*lbf }

    2. Mount the starter in a vise between aluminum plates.



    3. A075965E03
    4. Connect the battery and an ammeter to the starter as shown in the illustration.
      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal 30

    5. Check that the starter rotates smoothly and steadily while the pinion gear is moving out. Then measure the current.

      Standard current:
      90 A or less at 11.5 V

      If the result is not as specified, replace the starter assembly.



2. INSPECT STARTER ARMATURE ASSEMBLY
  1. Check the commutator for dirt and/or burns on the surface.
    If the surface is dirty and/or burnt, correct it with sandpaper (No. 400) or lathe. If necessary, replace the starter armature assembly.



  1. Inspect the commutator for an open circuit.



      A073983E15
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Segment
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Segment
      If the result is not as specified, replace the starter armature assembly.



  1. Inspect the commutator for a short circuit.



      A073984E14
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Segment - Coil core
      Always
      10 kΩ or higher

      Text in Illustration 
      *1
      Segment
      *2
      Coil Core
      If the result is not as specified, replace the armature assembly.



    A058584E20
  1. Using a vernier caliper, measure the protrusion length.

    Standard length:
    3.1 mm (0.122 in.)

    Maximum length:
    3.8 mm (0.150 in.)

    Text in Illustration 
    *1
    Depth
    If the length is more than the maximum, replace the starter armature assembly.



3. INSPECT STARTER COMMUTATOR END FRAME ASSEMBLY


  1. Check the brush length.



      A076677E16
    1. Using a vernier caliper, measure the brush length.

      Standard length:
      9.0 mm (0.354 in.)

      Minimum length:
      4.0 mm (0.157 in.)

      Text in Illustration 
      *1
      Length
      If the length is less than the minimum, replace the starter commutator end frame assembly.



  1. Inspect the insulation.



      A076436E02
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Positive (+) brush - Negative (-) brush
      Always
      10 kΩ or higher

      If the result is not as specified, repair or replace the commutator end frame assembly.



4. INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY
  1. Check the gear teeth on the planetary gear, internal gear and starter clutch for wear or damage.
    If any of the gears is damaged, replace the starter center bearing clutch sub-assembly.



  1. Check the starter clutch pinion gear.



      A221357
    1. Hold the starter clutch and rotate the pinion gear clockwise, and check that it turns freely. Try to rotate the pinion gear counterclockwise and check that it locks.
      Text in Illustration 
      V100135
      Free
      V100136
      Lock
      If necessary, replace the center bearing clutch sub-assembly.



5. INSPECT REPAIR SERVICE STARTER KIT


  1. Check the plunger.



      A058586E01
    1. Push in the plunger, and check that it returns quickly to it is original position.
      If the result is not as specified, replace the repair service starter kit.



  1. Inspect the pull-in coil.



      A076126E03
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminals 50 - Terminal C
      Always
      Below 1 Ω

      Text in Illustration 
      *1
      Terminal 50
      *2
      Terminal C
      If the result is not as specified, replace the repair service starter kit.



  1. Inspect the holding coil.



      A076129E03
    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      Terminal 50 - Switch body
      Always
      Below 2 Ω

      Text in Illustration 
      *1
      Terminal 50
      *2
      Switch Body
      If the result is not as specified, replace the repair service starter kit.