Home › ENGINE ยท 1UR-FE › ENGINE CONTROL SYSTEM › POWER STEERING OIL PRESSURE SWITCH

POWER STEERING OIL PRESSURE SWITCH > INSTALLATION

for Preparation Click here



1. INSTALL POWER STEERING OIL PRESSURE SWITCH
  1. Install a new O-ring to the power steering oil pressure switch.

  1. Apply a light coat of engine oil to the O-ring of the power steering oil pressure switch.

    NOTICE:
    1. When reusing the power steering oil pressure switch, inspect the O-ring.
    2. If the O-ring has scratches or cuts, replace the power steering oil pressure switch.



    A217901E01
  1. Using SST, install the power steering oil pressure switch.

    SST
    09922-10010  

    Torque:
    without SST:
    21 N*m{ 210 kgf*cm , 15 ft.*lbf }
    with SST:
    15 N*m{ 148 kgf*cm , 11 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 30 cm (11.8 in.). When using a torque wrench with a fulcrum length that is not 30 cm (11.8 in.), calculate the torque specification for the torque wrench and SST based on the "without SST" torque specification (Click here).
    2. Make sure SST and the torque wrench are connected in a straight line.

  1. Connect the oil pressure switch connector.



2. INSTALL FAN AND GENERATOR V BELT
  1. Install the fan and generator V belt (Click here).



3. ADD POWER STEERING FLUID


4. BLEED POWER STEERING FLUID
  1. Check the fluid level.

  1. Jack up the front of the vehicle and support it with stands.

  1. Turn the steering wheel.

    1. With the engine stopped, turn the wheel slowly from lock to lock several times.

  1. Lower the vehicle.

  1. Start the engine.

  1. Run the engine at idle for a few minutes.

  1. Turn the steering wheel.

    1. With the engine idling, turn the wheel left or right to the full lock position and keep it there for 2 to 3 seconds, and then turn the wheel to the opposite full lock position and keep it there for 2 to 3 seconds.*1

    2. Repeat *1 several times.

  1. Stop the engine.



    C124274E02
  1. Check for foaming or emulsification.
    If the system has to be bled twice because of foaming or emulsification, check for fluid leaks in the system.

  1. Check the fluid level.



5. INSPECT FOR POWER STEERING FLUID LEAK


6. CHECK FLUID LEVEL


    C158723E01
  1. Keep the vehicle horizontal.

  1. With the engine stopped, check the fluid level in the reservoir.
    If necessary, add fluid.

    Fluid:
    ATF DEXRON II or III

    HINT:
    If the fluid is hot, check that the fluid level is within the HOT range. If the fluid is cold, check that the fluid level is within the COLD range.

  1. Start the engine and run it at idle.

  1. Turn the steering wheel from lock to lock several times to raise the fluid temperature.

    Fluid temperature:
    80°C (176°F)



    C124274E02
  1. Check for foaming or emulsification.
    If foaming or emulsification is identified, bleed the power steering system.



    C124276E03
  1. With the engine idling, measure the fluid level in the reservoir.

  1. Stop the engine.

  1. Wait a few minutes and remeasure the fluid level in the reservoir.

    Maximum fluid level rise:
    5.0 mm (0.197 in.)

    If the fluid level rise is more than the maximum, bleed the power steering system.

  1. Check the fluid level.



7. INSTALL FRONT FENDER APRON SEAL RH
  1. Install the fender apron seal with the 6 clips.



8. INSTALL FRONT WHEEL

Torque:
for Aluminum Wheel:
131 N*m{ 1336 kgf*cm , 97 ft.*lbf }
for Steel Wheel:
209 N*m{ 2131 kgf*cm , 154 ft.*lbf }