Home › ENGINE ยท 1UR-FE › EXHAUST › EXHAUST PIPE (for Regular Cab Standard Deck)

EXHAUST PIPE (for Regular Cab Standard Deck) > REMOVAL

for Preparation Click here


CAUTION:
  1. Wear protective gloves when removing the exhaust pipe.
  2. The exhaust pipe is extremely hot immediately after the engine has stopped.
  3. Confirm that the exhaust pipe has cooled down before removing it.



1. REMOVE TAILPIPE ASSEMBLY


    A215356
  1. Remove the bolt, clamp and gasket.

  1. Disconnect the tailpipe from the exhaust pipe support.



2. REMOVE CENTER EXHAUST PIPE ASSEMBLY


    A215354
  1. Remove the 4 bolts.

  1. Disconnect the center exhaust pipe from the 3 exhaust pipe supports.

  1. Remove the center exhaust pipe from the front exhaust pipe and front No. 3 exhaust pipe.

  1. Remove the 2 gaskets from the front exhaust pipes.



3. REMOVE PROPELLER SHAFT HEAT INSULATOR (for 4WD)


C158452
  1. Remove the 2 bolts and heat insulator from the heat insulator bracket.



4. REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
  1. Disconnect the sensor connector.



    A215444E01
  1. Using SST, remove the sensor.

    SST
    09224-00010  



5. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY


    A215355
  1. Remove the 2 bolts and 2 nuts.

  1. Disconnect the front No. 3 exhaust pipe from the exhaust pipe support.

  1. Remove the front No. 3 exhaust pipe from the front No. 2 exhaust pipe.

  1. Disconnect the air fuel ratio sensor connector.



    A215357
  1. Remove the 3 nuts, front No. 2 exhaust pipe and 2 gaskets from the exhaust manifold LH.



6. REMOVE HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)


    A215447E01
  1. Disconnect the heated oxygen sensor connector and 2 clamps.

  1. Using SST, remove the sensor.

    SST
    09224-00010  



7. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.



    A215358
  1. Remove the 3 nuts, front exhaust pipe and gasket from the exhaust manifold RH.



8. REMOVE AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)


    A215441E01
  1. Using SST, remove the sensor.

    SST
    09224-00010  



9. REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)


    A215438E01
  1. Using SST, remove the sensor.

    SST
    09224-00010  



10. REMOVE MONOLITHIC CONVERTER PROTECTOR (for Bank 1)


A217263
  1. Remove the 4 bolts, 4 nuts, lower monolithic converter protector, upper monolithic converter protector, 2 No. 1 converter protector stays and 2 No. 2 converter protector stays.



11. REMOVE NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 1)


A217264
  1. Remove the 4 bolts, 4 nuts, lower No. 1 monolithic converter protector, upper No. 1 monolithic converter protector and 4 No. 1 converter protector stays.



12. REMOVE MONOLITHIC CONVERTER PROTECTOR (for Bank 2)


A217261
  1. Remove the 4 bolts, 4 nuts, lower monolithic converter protector, upper monolithic converter protector, 2 No. 1 converter protector stays and 2 No. 2 converter protector stays.



13. REMOVE NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 2)


A217262
  1. Remove the 4 bolts, 4 nuts, lower No. 1 monolithic converter protector, upper No. 1 monolithic converter protector and 4 No. 1 converter protector stays.