Home › ENGINE ยท 1UR-FE › EXHAUST › EXHAUST PIPE (except Regular Cab Standard Deck)

EXHAUST PIPE (except Regular Cab Standard Deck) > REMOVAL

for Preparation Click here


CAUTION:
  1. Wear protective gloves when removing the exhaust pipe.
  2. The exhaust pipe is extremely hot immediately after the engine has stopped.
  3. Confirm that the exhaust pipe has cooled down before removing it.



1. REMOVE TAILPIPE ASSEMBLY


    A215356
  1. Remove the bolt, clamp and gasket.

  1. Disconnect the tailpipe from the exhaust pipe support.



2. REMOVE CENTER EXHAUST PIPE ASSEMBLY


    A215354
  1. Remove the 4 bolts.

  1. Disconnect the center exhaust pipe from the 3 exhaust pipe supports.

  1. Remove the center exhaust pipe from the front exhaust pipe and front No. 2 exhaust pipe.

  1. Remove the 2 gaskets from the front exhaust pipes.



3. REMOVE PROPELLER SHAFT HEAT INSULATOR (for 4WD)


C158452
  1. Remove the 2 bolts and heat insulator from the heat insulator bracket.



4. REMOVE HEATED OXYGEN SENSOR (for Bank 1 Sensor 2)
  1. Disconnect the sensor connector.



    A215444E01
  1. Using SST, remove the sensor.

    SST
    09224-00010  



5. REMOVE FRONT NO. 2 EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.



    A215357
  1. Remove the 3 nuts.

  1. Disconnect the front No. 2 exhaust pipe from the exhaust pipe support to remove it.

  1. Remove the gasket.



6. REMOVE HEATED OXYGEN SENSOR (for Bank 2 Sensor 2)


    A215447E01
  1. Disconnect the heated oxygen sensor connector and 2 clamps.

  1. Using SST, remove the sensor.

    SST
    09224-00010  



7. REMOVE FRONT EXHAUST PIPE ASSEMBLY


    A215358
  1. Disconnect the air fuel ratio sensor connector.

  1. Remove the 3 nuts and the front exhaust pipe from the exhaust manifold RH.

  1. Remove the gasket.



8. REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)


    A215438E01
  1. Using SST, remove the sensor.

    SST
    09224-00010  



9. REMOVE AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)


    A215441E01
  1. Using SST, remove the sensor.

    SST
    09224-00010  



10. REMOVE MONOLITHIC CONVERTER PROTECTOR (for Bank 1)


A217263
  1. Remove the 4 bolts, 4 nuts, lower monolithic converter protector, upper monolithic converter protector, 2 No. 1 converter protector stays and 2 No. 2 converter protector stays.



11. REMOVE NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 1)


A217264
  1. Remove the 4 bolts, 4 nuts, lower No. 1 monolithic converter protector, upper No. 1 monolithic converter protector and 4 No. 1 converter protector stays.



12. REMOVE MONOLITHIC CONVERTER PROTECTOR (for Bank 2)


A217261
  1. Remove the 4 bolts, 4 nuts, lower monolithic converter protector, upper monolithic converter protector, 2 No. 1 converter protector stays and 2 No. 2 converter protector stays.



13. REMOVE NO. 1 MONOLITHIC CONVERTER PROTECTOR (for Bank 2)


A217262
  1. Remove the 4 bolts, 4 nuts, lower No. 1 monolithic converter protector, upper No. 1 monolithic converter protector and 4 No. 1 converter protector stays.