Home › DRIVE LINE › JF1A TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > DISASSEMBLY

for Preparation Click here



1. REMOVE PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY


    C180866
  1. Remove the bolt and propeller shaft heat insulator bracket sub-assembly.



2. REMOVE TRANSFER OIL PUMP PLATE


    C159613
  1. Remove the 4 bolts and transfer oil pump plate.

    NOTICE:
    Do not drop the transfer oil pump drive rotor and transfer oil pump driven rotor.



    C180851
  1. Remove the transfer oil seal ring from the transfer input shaft.



    C180850E02
  1. Remove the transfer oil pump drive rotor and transfer oil pump driven rotor.
    Text in Illustration 
    *1
    Transfer Oil Pump Drive Rotor
    *2
    Transfer Oil Pump Driven Rotor



    C180856
  1. Remove the O-ring from the transfer oil pump plate.



3. REMOVE TRANSFER CASE STRAIGHT PIN


    C162213E02
  1. Remove the 2 transfer case straight pins.

    NOTICE:
    Do not drop the transfer case straight pin.



4. REMOVE TRANSFER CASE PLUG


    C270581E01
  1. Using a 10 mm hexagon wrench, remove the transfer case plug, compression spring, ball and relief valve seat from the transfer oil pump plate.
    Text in Illustration 
    *1
    Transfer Case Plug
    *2
    Compression Spring
    *3
    Ball
    *4
    Relief Valve Seat



5. REMOVE TRANSFER OIL PUMP PLATE OIL SEAL


    C180855E01
  1. Using a screwdriver and hammer, tap out the transfer oil pump plate oil seal from the transfer oil pump plate.
    Text in Illustration 
    *1
    Protective Tape

    NOTICE:
    Be careful not to damage the transfer oil pump plate contact surfaces.



6. REMOVE FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    C180857E02
  1. Using SST and a hammer, loosen the staked part of the transfer output shaft nut.

    SST
    09930-00010  

    NOTICE:
    1. Be sure to use SST with the tapered surface facing the shaft.
    2. Do not grind the tip of SST with a grinder or other device.
    3. Completely loosen the staked part of the transfer output shaft nut when removing it.
    4. Do not damage the threads of the driven sprocket.



    C270547E01
  1. Using SST, hold the front output shaft companion flange sub-assembly.

    SST
    09330-00021  

  1. Using a 32 mm socket wrench, remove the transfer output shaft nut.
    Text in Illustration 
    *a
    Hold
    *b
    Turn



    C180859
  1. Remove the O-ring.



    C270548E01
  1. Using SST, remove the front output shaft companion flange sub-assembly.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)
    Text in Illustration 
    *a
    Hold
    *b
    Turn



7. REMOVE TRANSFER CASE FRONT OIL SEAL


    C180928E02
  1. Using SST, remove the transfer case front oil seal from the front transfer case.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the front transfer case contact surfaces.



8. REMOVE REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY


    C180861E02
  1. Using SST and a hammer, loosen the staked part of the transfer output shaft nut.

    SST
    09930-00010  

    NOTICE:
    1. Be sure to use SST with the tapered surface facing the shaft.
    2. Do not grind the tip of SST with a grinder or other device.
    3. Completely loosen the staked part of the transfer output shaft nut when removing it.
    4. Do not damage the threads of the rear transfer output shaft.



    C270549E01
  1. Using SST, hold the rear output shaft companion flange sub-assembly.

    SST
    09330-00021  

  1. Using a 32 mm socket wrench, remove the transfer output shaft nut.
    Text in Illustration 
    *a
    Hold
    *b
    Turn



    C180863
  1. Remove the O-ring.



    C270550E01
  1. Using SST, remove the rear output shaft companion flange sub-assembly.

    SST
    09950-40011   (09951-04020, 09952-04010, 09953-04030, 09954-04010, 09955-04051, 09957-04010, 09958-04011)
    Text in Illustration 
    *a
    Hold
    *b
    Turn



9. REMOVE TRANSFER CASE REAR OIL SEAL


    C180929E02
  1. Using SST, remove the transfer case rear oil seal from the rear transfer case.

    SST
    09308-00010  

    NOTICE:
    Be careful not to damage the rear transfer case contact surfaces.



10. REMOVE NO. 1 TRANSFER CASE PLUG


    C162211E01
  1. Remove the No. 1 transfer case plug, compression spring and pin.
    Text in Illustration 
    *1
    No. 1 Transfer Case Plug
    *2
    Compression Spring
    *3
    Pin



11. REMOVE TRANSFER CASE PLUG


    C180867
  1. Using a 6 mm hexagon wrench, remove the transfer case plug.



12. REMOVE REAR TRANSFER CASE


    C270584
  1. Remove the 14 bolts.

  1. Remove the rear transfer case.

    HINT:
    If necessary, tap the rear transfer case with a plastic-faced hammer to remove it.



13. REMOVE FRONT TRANSFER OUTPUT SHAFT NEEDLE ROLLER BEARING


    C270558
  1. Remove the front transfer output shaft needle roller bearing from the rear output shaft assembly.



14. REMOVE NO. 2 TRANSFER GEAR SHIFT FORK


    C159623
  1. Using 2 screwdrivers and a hammer, tap out the 3 transfer gear shift fork shaft snap rings.



    C159621E01
  1. Remove the bolt. Then remove the No. 2 transfer gear shift fork together with the transfer high and low clutch sleeve from the transfer shift actuator assembly.
    Text in Illustration 
    *1
    No. 2 Transfer Gear Shift Fork
    *2
    Transfer High and Low Clutch Sleeve

    NOTICE:
    Do not drop the transfer high and low clutch sleeve.



15. REMOVE NO. 1 TRANSFER GEAR SHIFT FORK


    C159622E01
  1. Remove the bolt. Then remove the No. 1 transfer gear shift fork together with the front drive clutch sleeve from the transfer shift actuator assembly.
    Text in Illustration 
    *1
    No. 1 Transfer Gear Shift Fork
    *2
    Front Drive Clutch Sleeve

    NOTICE:
    Do not drop the front drive clutch sleeve.



16. REMOVE TRANSFER SHIFT ACTUATOR ASSEMBLY


    C270585
  1. Remove the 3 bolts and transfer shift actuator assembly from the rear transfer case.



    C160356
  1. Remove the O-ring from the transfer shift actuator assembly.



17. REMOVE REAR OUTPUT SHAFT ASSEMBLY


    C173484
  1. Using a snap ring expander, expand the rear transfer output shaft snap ring.



    C271443
  1. Using a plastic-faced hammer, carefully tap the rear transfer case, and remove the rear output shaft assembly together with the drive chain and driven sprocket.

    NOTICE:
    1. When using a vise, place aluminum plates between the part and vise.
    2. When using a vise, do not overtighten it.

  1. Remove the rear output shaft assembly and driven sprocket from the drive chain.

    NOTICE:
    Do not drop the output washer.

  1. Using a snap ring expander, remove the rear transfer output shaft snap ring.



18. REMOVE SIDE GEAR SHAFT HOLDER BEARING


    C273275E01
  1. Using SST and a press, remove the side gear shaft holder bearing.

    SST
    09950-00020  
    09950-60010   (09951-00380)
    09950-70010   (09951-07150)



19. REMOVE TRANSFER OIL SEPARATOR SUB-ASSEMBLY


    C159718
  1. Remove the 3 bolts and transfer oil separator sub-assembly.



    C180885
  1. Remove the O-ring from the transfer oil separator sub-assembly.



20. REMOVE TRANSFER CASE MAGNET


21. REMOVE INPUT SHAFT ASSEMBLY


    C159719
  1. Using a 14 mm hexagon wrench, remove the 2 transfer case plugs from the front transfer case.



    C160522
  1. Expand the transfer input shaft hole snap ring. Then remove the input shaft assembly from the front transfer case.



22. REMOVE TRANSFER LOW PLANETARY RING GEAR


    F043456
  1. Using a screwdriver, remove the transfer low planetary ring gear hole snap ring. Then remove the transfer low planetary ring gear from the front transfer case.



    C180891
  1. Using a screwdriver, remove the transfer input shaft hole snap ring from the front transfer case.



23. REMOVE TRANSFER DRIVEN SPROCKET BEARING
  1. Remove the transfer driven sprocket bearing from the front transfer case.



24. REMOVE NO. 1 TRANSFER INPUT SHAFT SEAL RING


    C162486
  1. Remove the No. 1 transfer input shaft seal ring from the transfer input shaft.



25. REMOVE TRANSFER INPUT SHAFT BEARING


    C159629
  1. Using a snap ring expander, remove the transfer input shaft snap ring.



    C270552E01
  1. Using SST and a press, press out the transfer input shaft bearing.

    SST
    09555-55010  

    NOTICE:
    Be careful not to drop or damage the transfer low planetary gear assembly.



26. REMOVE TRANSFER LOW PLANETARY GEAR ASSEMBLY


    C159709
  1. Using a screwdriver, remove the transfer low planetary gear bearing shaft snap ring.

  1. Remove the transfer low planetary gear assembly, 2 transfer low planetary gear bearings and transfer low planetary gear spline piece from the transfer input shaft.



27. REMOVE TRANSFER INPUT SHAFT PLUG


    C270587E01
  1. Using SST and a hammer, tap out the transfer input shaft plug.

    SST
    09950-60010   (09951-00300)
    09950-70010   (09951-07200)



28. REMOVE NO. 1 TRANSFER OUTPUT SHAFT SPACER


    C270553
  1. Using 2 screwdrivers, tap out the transfer clutch hub shaft snap ring.

  1. Remove the No. 1 transfer output shaft spacer, transfer low planetary gear bearing and transfer output spacer from the rear transfer output shaft.



    C173604E01
  1. Remove the transfer oil seal ring from the No. 1 transfer output shaft spacer.
    Text in Illustration 
    *1
    Transfer Oil Seal Ring
    *2
    No. 1 Transfer Output Shaft Spacer



29. REMOVE TRANSFER CLUTCH HUB
  1. Using a snap ring expander, remove the transfer clutch hub shaft snap ring.



    C159714E01
  1. Using SST and a press, press out the transfer clutch hub.

    SST
    09527-10011  

    NOTICE:
    Be careful not to drop or damage the rear transfer output shaft.



30. REMOVE REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING
  1. Remove the 2 output washers.



    C270555E01
  1. Using SST and a press, press out the rear transfer output shaft radial ball bearing.

    SST
    09555-55010  

    NOTICE:
    Be careful not to drop or damage the rear transfer output shaft.

  1. Remove the transfer drive sprocket sub-assembly and transfer drive sprocket bearing.

  1. Remove the transfer synchronizer ring set.



31. REMOVE TRANSFER DRIVE CLUTCH HUB


    C159715
  1. Using 2 screwdrivers, tap out the transfer clutch hub shaft snap ring.



    C159717E01
  1. Using SST and a press, press out the transfer drive clutch hub.

    SST
    09527-10011  



    D030010E04
  1. Remove the 2 No. 1 transfer synchromesh shifting key springs and 3 No. 1 transfer synchromesh shifting keys from the transfer drive clutch hub.
    Text in Illustration 
    *1
    No. 1 Transfer Synchromesh Shifting Key Spring
    *2
    No. 1 Transfer Synchromesh Shifting Key