Home › DRIVE LINE › JF1A TRANSFER › TRANSFER ASSEMBLY

TRANSFER ASSEMBLY > REASSEMBLY

for Preparation Click here


HINT:
Coat all of the sliding and rotating surfaces with gear oil before reassembly.



1. INSTALL TRANSFER DRIVE CLUTCH HUB


    C159738E01
  1. Using SST and a press, press in the transfer drive clutch hub.

    SST
    09513-36040  

  1. Using a snap ring expander, install the transfer clutch hub shaft snap ring.



2. INSTALL FRONT DRIVE CLUTCH SLEEVE
  1. Apply gear oil to the connecting areas of the front drive clutch sleeve and transfer drive clutch hub.



    C270588E01
  1. Install the front drive clutch sleeve onto the rear transfer output shaft.
    Text in Illustration 
    *a
    Rear Side

    NOTICE:
    Make sure that the front drive clutch sleeve is installed facing the correct direction.



    D030010E04
  1. Install the 3 No. 1 transfer synchromesh shifting keys and 2 No. 1 transfer synchromesh shifting key springs.
    Text in Illustration 
    *1
    No. 1 Transfer Synchromesh Shifting Key Spring
    *2
    No. 1 Transfer Synchromesh Shifting Key

    NOTICE:
    Install the No. 1 transfer synchromesh shifting key springs so that their end gaps are not aligned.



3. INSTALL TRANSFER SYNCHRONIZER RING SET
  1. Apply transfer oil to the transfer synchronizer ring set.



    C159810
  1. Install the transfer synchronizer ring set (outer synchronizer ring) onto the rear transfer output shaft.

    NOTICE:
    Align the slots of the transfer synchronizer ring set (outer synchronizer ring) with the No. 1 transfer synchromesh shifting keys.



    C159811
  1. Install the transfer synchronizer ring set (center synchronizer ring) onto the rear transfer output shaft.



    C159812
  1. Install the transfer synchronizer ring set (inner synchronizer ring) onto the rear transfer output shaft.

    NOTICE:
    Align the slots of the transfer synchronizer ring set (outer synchronizer ring) with those of the transfer synchronizer ring set (inner synchronizer ring).



4. INSTALL TRANSFER DRIVE SPROCKET SUB-ASSEMBLY


    C159813
  1. Install a new transfer drive sprocket bearing.



    C159814
  1. Install the transfer drive sprocket sub-assembly.

    NOTICE:
    Align the cutouts in the transfer drive sprocket sub-assembly with the protrusions on the transfer synchronizer ring set (center synchronizer ring).



5. INSTALL REAR TRANSFER OUTPUT SHAFT RADIAL BALL BEARING


    C270586E01
  1. Using SST and a press, press in a new rear transfer output shaft radial ball bearing.

    SST
    09316-60011   (09316-00011)

    NOTICE:
    Make sure the rear transfer output shaft radial ball bearing is installed in the correct direction.

    Text in Illustration 
    *a
    Rear Side



6. INSPECT TRANSFER DRIVE SPROCKET SUB-ASSEMBLY


    C159816
  1. Using a feeler gauge, measure the transfer drive sprocket sub-assembly thrust clearance.

    Standard clearance:
    0.10 to 0.26 mm (0.00394 to 0.0102 in.)

    Maximum clearance:
    0.26 mm (0.0102 in.)

    If the clearance is more than the maximum, replace the transfer drive sprocket sub-assembly.



7. INSTALL TRANSFER CLUTCH HUB


    C159817E01
  1. Using SST and a press, press in the transfer clutch hub.

    SST
    09316-60011   (09316-00011)



    C159818
  1. Select a transfer clutch hub shaft snap ring that allows for minimum axial play and install it to the rear transfer output shaft.

    Snap Ring Thickness:
    Mark
    Thickness
    B
    2.12 to 2.17 mm (0.0835 to 0.0854 in.)
    C
    2.17 to 2.22 mm (0.0855 to 0.0874 in.)
    D
    2.22 to 2.27 mm (0.0875 to 0.0893 in.)
    E
    2.27 to 2.32 mm (0.0894 to 0.0913 in.)
    F
    2.32 to 2.37 mm (0.0914 to 0.0933 in.)
    G
    2.37 to 2.42 mm (0.0934 to 0.0952 in.)
    H
    2.42 to 2.47 mm (0.0953 to 0.0972 in.)
    J
    2.47 to 2.52 mm (0.0973 to 0.0992 in.)
    K
    2.52 to 2.57 mm (0.0993 to 0.1011 in.)

  1. Using a snap ring expander, install the transfer clutch hub shaft snap ring.

    NOTICE:
    Make sure that the transfer clutch hub shaft snap ring is firmly installed to the groove.



8. INSTALL NO. 1 TRANSFER OUTPUT SHAFT SPACER
  1. Apply transfer oil to a new transfer oil seal ring and transfer low planetary gear bearing.



    C173604E01
  1. Install the transfer oil seal ring to the No. 1 transfer output shaft spacer.
    Text in Illustration 
    *1
    Transfer Oil Seal Ring
    *2
    No. 1 Transfer Output Shaft Spacer

  1. Apply transfer oil to the transfer low planetary gear bearing.



    C270556E01
  1. Install the transfer output spacer, transfer low planetary gear bearing and No. 1 transfer output shaft spacer to the rear transfer output shaft.
    Text in Illustration 
    *1
    Transfer Output Spacer
    *2
    Transfer Low Planetary Gear Bearing
    *3
    No. 1 Transfer Output Shaft Spacer



    C270557
  1. Using a snap ring expander, install the transfer clutch hub shaft snap ring.

    NOTICE:
    Make sure that the transfer clutch hub shaft snap ring is firmly installed to the groove.



9. INSTALL TRANSFER CASE FRONT OIL SEAL


    C159805E02
  1. Using SST and a hammer, tap in a new transfer case front oil seal as shown in the illustration.

    SST
    09316-60011   (09316-00011)

    Drive in depth (A):
    1.0 to 1.5 mm (0.0394 to 0.0590 in.)

    NOTICE:
    Be careful not to damage the front transfer case.



10. INSTALL TRANSFER DRIVEN SPROCKET BEARING


    C162208E01
  1. Install a new transfer driven sprocket bearing to the front transfer case in the direction shown in the illustration.

    NOTICE:
    Make sure the transfer driven sprocket bearing is installed in the correct direction.

    Text in Illustration 
    *a
    Front Side



11. INSTALL TRANSFER LOW PLANETARY RING GEAR


    F043457E07
  1. Install the transfer low planetary ring gear to the transfer front case.
    Text in Illustration 
    *a
    Front Side

    NOTICE:
    Make sure to install the transfer low planetary ring gear in the correct direction.



    F043456
  1. Using a screwdriver, install the transfer low planetary ring gear hole snap ring.

    NOTICE:
    Make sure that the transfer low planetary ring gear hole snap ring is firmly installed to the groove.



12. INSTALL TRANSFER INPUT SHAFT PLUG


    C271430E01
  1. Using SST and a hammer, tap in a new transfer input shaft plug as shown in the illustration.

    SST
    09950-60010   (09951-00400)
    09950-70010   (09951-07200)

    Drive in depth (A):
    1.0 to 1.8 mm (0.0394 to 0.0708 in.)

    NOTICE:
    Be careful not to damage or deform the transfer input shaft plug when tapping it.



13. INSTALL TRANSFER LOW PLANETARY GEAR ASSEMBLY


    C160521E02
  1. Install the transfer low planetary gear bearing and transfer low planetary gear assembly to the transfer input shaft.

    NOTICE:
    Make sure the transfer low planetary gear bearing is installed in the correct direction.

    Text in Illustration 
    *1
    Transfer Low Planetary Gear Bearing
    *2
    Transfer Low Planetary Gear Assembly
    *3
    Transfer Input Shaft
    *a
    Temper Color Side

  1. Install the transfer low planetary gear spline piece.



    C159709
  1. Using a screwdriver, install the transfer low planetary gear bearing shaft snap ring.

    NOTICE:
    Make sure that the end gap of the transfer low planetary gear bearing shaft snap ring is not aligned with the cutout of the planetary carrier.



14. INSTALL TRANSFER INPUT SHAFT BEARING


    C173498E03
  1. Install the transfer low planetary gear bearing and a new transfer input shaft bearing to the transfer input shaft.
    Text in Illustration 
    *1
    Transfer Low Planetary Gear Bearing
    *2
    Transfer Input Shaft Bearing
    *a
    Temper Color Side

    NOTICE:
    1. Make sure that the transfer input shaft bearing is installed in the correct direction.
    2. Make sure that the transfer low planetary gear bearing is installed in the correct direction.
    3. Make sure that the temper color side of the transfer low planetary gear bearing faces downward.



    C159710E01
  1. Using SST and a press, press in the transfer input shaft bearing.

    SST
    09513-36040  

    NOTICE:
    After press-fitting the transfer input shaft bearing to the transfer input shaft, check that the transfer input shaft bearing moves smoothly.



    C160525
  1. Select a transfer input shaft snap ring that allows for minimum axial play and install it to the transfer input shaft.

    Snap Ring Thickness:
    Mark
    Thickness
    C
    2.13 to 2.18 mm (0.0839 to 0.0858 in.)
    D
    2.18 to 2.23 mm (0.0859 to 0.0877 in.)
    E
    2.23 to 2.28 mm (0.0878 to 0.0897 in.)
    F
    2.28 to 2.33 mm (0.0898 to 0.0917 in.)
    G
    2.33 to 2.38 mm (0.0918 to 0.0937 in.)
    H
    2.38 to 2.43 mm (0.0938 to 0.0956 in.)
    J
    2.43 to 2.48 mm (0.0957 to 0.0976 in.)

  1. Using a snap ring expander, install the transfer input shaft snap ring.

    NOTICE:
    Make sure that the transfer input shaft snap ring is firmly installed to the groove.



15. INSTALL NO. 1 TRANSFER INPUT SHAFT SEAL RING


    C162486
  1. Install a new No. 1 transfer input shaft seal ring to the transfer input shaft.



16. INSTALL TRANSFER OIL SEAL RING
  1. Apply transfer oil to a new transfer oil seal ring.



    C162471
  1. Install the transfer oil seal ring to the transfer input shaft.



17. INSTALL INPUT SHAFT ASSEMBLY


    C160354
  1. Install the transfer input shaft hole snap ring to the front transfer case.



    C160522
  1. While expanding the transfer input shaft hole snap ring, install the input shaft assembly to the front transfer case.



    C159719
  1. Clean the threads of the 2 transfer case plugs and the front transfer case with non-residue solvent.

  1. Apply adhesive to the threads of the 2 transfer case plugs.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the transfer case plug within 3 minutes of application.

  1. Using a 14 mm hexagon wrench, install the 2 transfer case plugs.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }



18. INSTALL TRANSFER CASE MAGNET


19. INSTALL TRANSFER OIL SEPARATOR SUB-ASSEMBLY


    C180885E01
  1. Install a new O-ring.



    C159718
  1. Install the transfer oil separator sub-assembly with the 3 bolts.

    Torque:
    18 N*m{ 178 kgf*cm , 13 ft.*lbf }



20. INSTALL TRANSFER CASE REAR OIL SEAL


    C271431E01
  1. Using SST and a hammer, tap in a new transfer case rear oil seal as shown in the illustration.

    SST
    09316-60011   (09316-00011)

    Drive in depth (A):
    62.2 to 62.7 mm (2.45 to 2.46 in.)

    NOTICE:
    Be careful not to damage the rear transfer case.



21. INSTALL SIDE GEAR SHAFT HOLDER BEARING


    C273276E01
  1. Using SST and a press, install a new side gear shaft holder bearing.

    SST
    09214-60010  

    NOTICE:
    Press in the side gear shaft holder bearing until they fit to the edge.



22. INSTALL REAR OUTPUT SHAFT


    C180880
  1. Install the rear transfer output shaft snap ring to the rear transfer case.

  1. Fix the rear transfer case in a vise between aluminum plates.

    NOTICE:
    Do not overtighten the vise.



    C162212
  1. Install the 2 output washers to the rear output shaft assembly.



    C160360
  1. Install the rear output shaft assembly, front drive chain and driven sprocket to the rear transfer case.

    NOTICE:
    Do not drop the front drive clutch sleeve or shifting key.



    C173484
  1. Using a snap ring expander, install the rear transfer output shaft snap ring to the rear output shaft assembly.

    NOTICE:
    Make sure that the rear transfer output shaft snap ring is firmly installed to the groove.



23. INSTALL TRANSFER HIGH AND LOW CLUTCH SLEEVE


    C160351E02
  1. Install the transfer high and low clutch sleeve to the rear output shaft assembly.
    Text in Illustration 
    *1
    Transfer High and Low Clutch Sleeve
    *2
    Transfer Clutch Hub
    *a
    Front Side

    NOTICE:
    Make sure that the transfer high and low clutch sleeve is installed facing the correct direction.



24. INSTALL TRANSFER SHIFT ACTUATOR ASSEMBLY


    C160356
  1. Install a new O-ring to the transfer shift actuator assembly.



    C270585
  1. Set the No. 1 transfer gear shift fork and No. 2 transfer gear shift fork to the rear output shaft assembly. Then install the transfer shift actuator assembly to the rear transfer case with the 3 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }



25. INSTALL NO. 1 TRANSFER GEAR SHIFT FORK


    C159622
  1. Install the No. 1 transfer gear shift fork to the transfer shift actuator assembly with the bolt.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }



26. INSTALL NO. 2 TRANSFER GEAR SHIFT FORK


    C159621
  1. Install the No. 2 transfer gear shift fork to the transfer shift actuator assembly with the bolt.

    Torque:
    24 N*m{ 245 kgf*cm , 18 ft.*lbf }



    C160524
  1. Using a screwdriver and hammer, tap the 3 transfer gear shift fork shaft snap rings into the transfer shift actuator assembly.



27. INSTALL REAR TRANSFER CASE
  1. Apply transfer oil to the front transfer output shaft needle roller bearing.



    C270558
  1. Install the front transfer output shaft needle roller bearing to the rear output shaft assembly.



    C160517E03
  1. Apply seal packing to the rear transfer case as shown in the illustration.

    Seal packing:
    Toyota Genuine Seal Packing 1281, Three Bond 1281 or equivalent

    Text in Illustration 
    *1
    Seal Packing

    NOTICE:
    If the removed rear transfer case will be reused: After removing the rear transfer case, be sure to perform the following before reinstalling it: 1) using a knife, cut off any old FIPG on the rear transfer case's contact surface, 2) clean off any remaining old FIPG from the rear transfer case's contact surface, and 3) reapply seal packing to the rear transfer case.



    C270584
  1. Install the rear transfer case with the 14 bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

    NOTICE:
    Tighten the bolts of the rear transfer case within 10 minutes of applying the seal packing. The seal packing will dry very quickly.



28. INSTALL TRANSFER CASE PLUG


    C180867
  1. Clean the threads of the transfer case plug and the front transfer case with non-residue solvent.

  1. Apply adhesive to the threads of the transfer case plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the transfer case plug within 3 minutes of application.

  1. Using a 6 mm hexagon wrench, install the transfer case plug.

    Torque:
    39 N*m{ 400 kgf*cm , 29 ft.*lbf }



29. INSTALL NO. 1 TRANSFER CASE PLUG
  1. Clean the threads of the No. 1 transfer case plug and the front transfer case with non-residue solvent.

  1. Apply adhesive to the threads of the No. 1 transfer case plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the No. 1 transfer case plug within 3 minutes of application.



    C162211E01
  1. Install the pin, compression spring and No. 1 transfer case plug to the front transfer case.

    Torque:
    19 N*m{ 190 kgf*cm , 14 ft.*lbf }

    Text in Illustration 
    *1
    No. 1 Transfer Case Plug
    *2
    Compression Spring
    *3
    Pin



30. INSTALL FRONT OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Install the front output shaft companion flange sub-assembly onto the driven sprocket.



    C270559E01
  1. Using SST to hold the front output shaft companion flange sub-assembly, install a new companion flange lock nut.

    SST
    09330-00021  

  1. Using a 32 mm socket wrench, install a new O-ring and a new transfer output shaft nut.

    Torque:
    127 N*m{ 1299 kgf*cm , 94 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    *b
    Turn



    F050151E04
  1. Using a chisel and hammer, stake the transfer output shaft nut.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect



31. INSTALL REAR OUTPUT SHAFT COMPANION FLANGE SUB-ASSEMBLY
  1. Install the rear output shaft companion flange sub-assembly onto the rear transfer output shaft.



    C270560E01
  1. Using SST, hold the rear output shaft companion flange sub-assembly.

    SST
    09330-00021  

  1. Using a 32 mm socket wrench, install a new O-ring and a new transfer output shaft nut.

    Torque:
    127 N*m{ 1299 kgf*cm , 94 ft.*lbf }

    Text in Illustration 
    *a
    Hold
    *b
    Turn



    F050151E04
  1. Using a chisel and hammer, stake the transfer output shaft nut.
    Text in Illustration 
    *a
    Correct
    *b
    Incorrect



32. INSTALL TRANSFER OIL PUMP PLATE OIL SEAL


    C159806E03
  1. Using SST and a hammer, tap in a new transfer oil pump plate oil seal as shown in the illustration.

    SST
    09950-60010   (09951-00680)
    09950-70010   (09951-07100)

    Drive in depth (A):
    0.5 mm or less (0.0196 in. or less)

    NOTICE:
    Be careful not to damage the transfer oil pump plate.



33. INSTALL TRANSFER CASE PLUG


    C270581E01
  1. Install the relief valve seat, ball and compression spring to the transfer oil pump plate.
    Text in Illustration 
    *1
    Transfer Case Plug
    *2
    Compression Spring
    *3
    Ball
    *4
    Relief Valve Seat

  1. Clean the threads of the transfer case plug and the transfer oil pump plate with non-residue solvent.

  1. Apply adhesive to the threads of the transfer case plug.

    Adhesive:
    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

    NOTICE:
    Install the transfer case plug within 3 minutes of application.

  1. Using a 10 mm hexagon wrench, install the transfer case plug.

    Torque:
    29 N*m{ 300 kgf*cm , 22 ft.*lbf }



34. INSTALL TRANSFER CASE STRAIGHT PIN


    C162213E02
  1. Install the 2 transfer case straight pins to the transfer input shaft.



35. INSTALL TRANSFER OIL PUMP PLATE
  1. Apply transfer oil to a new O-ring, transfer oil pump drive rotor and transfer oil pump driven rotor.



    C180856
  1. Install the O-ring.



    C180850E03
  1. Install the transfer oil pump drive rotor and transfer oil pump driven rotor.
    Text in Illustration 
    *1
    Transfer Oil Pump Drive Rotor
    *2
    Transfer Oil Pump Driven Rotor



    C159613
  1. Install the transfer oil pump plate with the 4 bolts.

    Torque:
    12 N*m{ 117 kgf*cm , 8 ft.*lbf }



36. INSTALL PROPELLER SHAFT HEAT INSULATOR BRACKET SUB-ASSEMBLY


    C180866
  1. Install the propeller shaft heat insulator bracket sub-assembly with the bolt.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }