STARTER (for 2.0 kW Type) > INSPECTION |
| 1. INSPECT STARTER ASSEMBLY |
Mount the starter in a vise between aluminum plates.
Perform a pull-in test.
Remove the nut and disconnect the field coil wire from terminal C.
![]() |
Connect the battery to the magnet starter switch as shown in the illustration. Then check that the clutch pinion gear moves outward.
If the clutch pinion gear does not move outward, replace the magnet starter switch assembly.
Perform a holding test.
![]() |
Disconnect the negative (-) lead from terminal C with the condition specified in the pull-in test above being maintained. Check that the pinion gear remains out.
If the clutch pinion gear moves inward, replace the magnet starter switch assembly.
Inspect clutch pinion gear return.
![]() |
Disconnect the negative (-) lead from the starter body. Check that the clutch pinion gear moves inward.
If the clutch pinion gear does not move inward, replace the magnet starter switch assembly.
Perform an operation test without load.
![]() |
Connect the field coil wire to terminal C with the nut.
Connect the battery and an ammeter to the starter as shown in the illustration.
Check that the starter rotates smoothly and steadily while the pinion gear is moving outward. Then measure the current.
| 2. INSPECT STARTER ARMATURE ASSEMBLY |
Check the surface of the commutator for dirt and burns.
If the surface is dirty or burnt, correct it with sandpaper (No. 400) or a lathe.
If necessary, replace the starter armature assembly.
Inspect the commutator for an open circuit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Segment - Segment | Always | Below 1 Ω |
Inspect the commutator for a short circuit.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Segment - Coil core | Always | 10 kΩ or higher |
![]() |
Using a vernier caliper, measure the commutator diameter.
Check the commutator runout.
Place the armature shaft on V-blocks.
![]() |
Using a dial indicator, measure the circle runout.
![]() |
Using a vernier caliper, measure the undercut depth of the commutator.
| 3. INSPECT STARTER BRUSH HOLDER ASSEMBLY |
![]() |
Using a vernier caliper, measure the brush length.
Inspect the load of the brush spring.
![]() |
Take a pull scale reading immediately after the brush spring separates from the brush.
| 4. INSPECT STARTER CENTER BEARING CLUTCH SUB-ASSEMBLY |
Check the gear teeth of the planetary gears and starter center bearing clutch for wear or damage.
If any planetary gear is damaged, replace the planetary gear assembly. If any teeth of the starter center bearing clutch are damaged, replace the starter center bearing clutch sub-assembly.
Check the movement of the clutch pinion gear.
![]() |
Rotate the clutch pinion gear clockwise, and check that it turns freely.
Try to rotate the clutch pinion gear counterclockwise, and check that it locks.
If the clutch pinion gear cannot be turned clockwise smoothly, or does not lock in the counterclockwise direction, replace the starter center bearing clutch sub-assembly.
| 5. INSPECT MAGNET STARTER SWITCH ASSEMBLY |
Inspect the pull-in coil.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Terminal 50 - Terminal C | Always | Below 1 Ω |
Inspect the holding coil.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Terminal 50 - Switch body | Always | Below 2 Ω |