Home › ENGINE · 3UR-FBE › STARTING › STARTER

STARTER > REMOVAL

for Preparation Click here



1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).



2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


3. REMOVE NO. 1 ENGINE UNDER COVER


    A150108
  1. Remove the 3 screws and 5 bolts.

  1. Unhook the engine under cover from the vehicle body as shown in the illustration.



4. REMOVE V-BANK COVER SUB-ASSEMBLY


    A165576E01
  1. Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.



5. REMOVE AIR CLEANER HOSE ASSEMBLY


    A162102E01
  1. Disconnect the vacuum hose and ventilation hose.

  1. Loosen the 2 clamps.

  1. Remove the air cleaner hose.



6. REMOVE AIR CLEANER ASSEMBLY


    A162105E01
  1. Remove the air cleaner cap.

    1. Disconnect the MAF meter connector.

    2. Using a clip remover, detach the wire harness clamp.

    3. Unfasten the 4 hook clamps and then remove the air cleaner cap.

  1. Remove the air cleaner element.



    A156197E01
  1. Remove the 2 bolts and air cleaner case.



7. REMOVE FAN AND GENERATOR V BELT


    A163770E01
  1. While turning the belt tensioner counterclockwise, align the service hole for the belt tensioner and the belt tensioner fixing position, and then insert a bar of φ 5 mm (0.197 in.) into the service hole to fix the belt tensioner in place.

    HINT:
    The pulley bolt for the belt tensioner has a left-hand thread.

  1. Remove the V belt.



8. REMOVE FRONT FENDER APRON SEAL RH
  1. Remove the 5 clips and apron seal.



9. DISCONNECT VANE PUMP ASSEMBLY


    A164433
  1. Detach the 2 clamps and disconnect the power steering oil pressure switch connector.



    A163289
  1. Remove the 2 bolts and disconnect the vane pump.



10. REMOVE GENERATOR ASSEMBLY


    A163292
  1. Disconnect the generator connector.

  1. Remove the terminal cap and nut, and disconnect the generator wire.



    A163290
  1. Remove the bolt and disconnect the wire harness bracket from the generator.



    A260951
  1. Remove the 3 bolts, nut and generator.



11. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE
  1. Remove the dipstick.



    A164432
  1. Remove the bolt and dipstick guide.

  1. Remove the O-ring from the dipstick guide.



12. REMOVE FRONT EXHAUST PIPE ASSEMBLY
  1. Disconnect the air fuel ratio sensor connector.

  1. Disconnect the heated oxygen sensor connector and detach the 2 clamps.

  1. Remove the 2 bolts.

  1. Remove the 3 nuts and front exhaust pipe.

  1. Remove the 2 gaskets.



13. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR


    A162752
  1. Remove the 3 bolts and heat insulator.



14. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH


    A162754
  1. Remove the 10 nuts, exhaust manifold and 2 gaskets.



15. REMOVE STARTER COVER


    A162756
  1. Remove the 3 bolts and starter cover.



16. REMOVE STARTER ASSEMBLY


    A258301
  1. Detach the 2 wire harness clamps.

  1. Disconnect the starter connector.

  1. Remove the nut and disconnect the starter wire.



    A258302
  1. Remove the 2 bolts and starter.



    A162758
  1. Remove the flywheel housing side cover.