LIN COMMUNICATION SYSTEM > TERMINALS OF ECU |
| CHECK MAIN BODY ECU (DRIVER SIDE JUNCTION BLOCK) |

Disconnect the DA and DD main body ECU (driver side junction block) connectors.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| DA-1 (ACC) - Body ground | B - Body ground | ACC power supply | Always | 11 to 14 V |
| DA-1 (IG) - Body ground | B - Body ground | IG power supply | Always | 11 to 14 V |
| DD-62 (GND1) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
| DD-62 (GND2) - Body ground | W-B - Body ground | Body ground | Always | Below 1 Ω |
| CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY (for Power Window Control System [w/ Jam Protection Function]) |

Disconnect the N2 power window regulator master switch assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| N2-3 (B) - N2-1 (E) | L - W-B | Battery power supply | Always | 11 to 14 V |
| N2-1 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (for Power Window Control System [w/ Jam Protection Function]) |

Disconnect the N12 front power window regulator motor assembly LH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| N12-2 (B) - N12-1 (GND) | G - W-B | Battery power supply | Always | 11 to 14 V |
| N12-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| CHECK FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (for Power Window Control System [w/ Jam Protection Function]) |

Disconnect the M11 front power window regulator motor assembly RH connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| M11-2 (B) - M11-1 (GND) | V - W-B | Battery power supply | Always | 11 to 14 V |
| M11-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| CHECK SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (w/ Sliding Roof System) |

Disconnect the W3 sliding roof drive gear sub-assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| W3-9 (IG) - Body ground | SB - Body ground | IG power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch OFF | Below 1 V | |||
| W3-10 (B) - Body ground | L - Body ground | +B power supply | Always | 11 to 14 V |
| W3-8 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY (A/C ECU) |

Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| J19-1 (IG+) - J19-14 (GND) | P - W-B | Ignition power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch OFF | Below 1 V | |||
| J19-21 (B) - J19-14 (GND) | R - W-B | Battery power source | Always | 11 to 14 V |
| J19-14 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| CHECK INTEGRATION CONTROL AND PANEL ASSEMBLY |

Disconnect the J37 integration control and panel assembly connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Terminal No. (Symbols) | Wiring Color | Terminal Description | Condition | Specified Condition |
| J37-16 (IG+) - J37-1 (GND) | P - W-B | Ignition power supply | Ignition switch ON | 11 to 14 V |
| Ignition switch OFF | Below 1 V | |||
| J37-1 (GND) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |